We are surrounded by various objects with movable, articulated parts, e.g., box, handle, door. An accurate and generalizable perception of articulated parts is essential to enhance robotic manipulation capabilities. Building on this need, recent efforts in articulated parts perception have followed two main directions: One line of work uses pose-based representation, which requires high manual cost; in parallel, affordance-based methods extract future object motion from point tracking without additional manual efforts, but suffer from low-quality data. In this paper, we propose a new representation of articulated parts, Geometric Primary Structure (GPS), an abstraction of the part geometry structure to balance scalability and quality. For efficient and scalable data collection, GPS is integrated with a portable Virtual Reality (VR) device and requires only one minute to annotate one object sequence. This direct human annotation provides higher quality than the estimated affordance. With this efficient VR-GPS system, we collect 41K frames for 234 objects across six part classes, and train a generalizable GPS model with a single RGB-D object image as input. For object manipulation, we deploy a heuristic policy based on GPS prediction. Without any in-domain fine-tuning, our method achieves an 73% success rate, covering 270 initial states for 9 objects. Our code, data and reusable tool are available at https://enlighten0707.github.io/gps.
Articulated object manipulation is a unique challenge for service robots. Existing methods employ end-to-end policy learning, visionmotion planning, and large-language/visual-language model (LLM/VLM), but often overlook the diversity of articulated objects and the complexity of interactions between end-effector and handle, leading to limited generalization and destructive collisions. To address this, we propose GSAM, a generalizable and safe robotic framework for articulated object manipulation. Specifically, a vision-based perceiver generates the kinematic parameters. Considering that pre-trained markers in perceiver yield raw estimations that may deviate from commonsense, we present a f ine-tuned VLM-based refiner, using chain-of-thought (COT) commonsense reasoning to refine perception. To prevent destructive collisions, we design an interaction constraint function generator, integrating articulated object, interaction pose, and obstacle avoidance knowledge into a base. LLM then functionalize these constraints and apply them to trajectory and posture planning. A kinematic-aware manipulation planner verifies reachability for trajectory and posture. Experiments on 50 hinge tasks across 5 object categories and 50 randomly initialized end-effectorhandle configurations show that GSAM reduces standard deviation by 3.1% and improves manipulation success rate by 36.0% compared to the best baseline, respectively demonstrating the superior object generalization and interaction safety of GSAM in practical scenarios.
Generalizing robotic manipulation to unseen objects remains challenging, as learning-based approaches require many demonstrations and fail in few-shot settings. Prior work transfers affordances through semantic retrieval, but semantics alone neglect geometric similarity, which is critical for manipulation. We propose GRAFT, a geometry-aware correspondence framework for zero-shot manipulation transfer using only one demonstration per object. Objects are represented as part-based graphs, where part-level descriptors support global instance retrieval and part correspondence, and vertex-level descriptors enable fine-grained contact point matching. For an unseen object, our method first retrieves the most functionally and geometrically similar instance from the demonstration buffer with aligned functional parts, and finally propagates the contact points through point-wise correspondence.
Replicating real-world environments into simulation by realistic visual representation like NeRF and 3D Gaussian Splatting (3DGS) has emerged as an effective strategy to reduce the sim-to-real gap in robot learning. However, implementing object articulation during the real-to-sim process is still a challenging task. Existing motion tracking or learning based articulation methods shows low success rates on complex kinematic structures having multiple joints. Furthermore, those methods require scan of dynamic motion of objects, which makes reconstruction process much complicated. In this work, we propose the first end-to-end pipeline that reconstructs simulation-ready assets with accurate articulation from a single static object video input through suggestion based human-in-the-loop process. Our approach exports a hybrid representation combining 3DGS for photorealistic rendering and mesh-based geometry for physical interaction. In the reconstruction process, our pipeline performs convex decomposition followed by user grouping for intuitive part segmentation, subsequently binding 3D Gaussians to the corresponding mesh parts. An Automatic Joint Suggestion Algorithm then calculates candidate joint axes from local boundary geometries and presents them to users for efficient articulated asset reconstruction. We have shown that our method achieves precise articulation results on partnet-mobility-v0 dataset and real objects. Additionally we presented a potential usage of our framework on robot learning, deploying the reconstructed assets in Unreal Engine and NVIDIA Isaac Sim, demonstrating real-time dexterous hand manipulation tasks.