TacClip: a clip-on sensor measures dynamic contact forces without covering the fingerpads

Human-centric data collection is emerging as a significant paradigm for robot skill acquisition, but seamlessly integrating low-cost, scalable tactile sensing systems that capture fine-grained fingertip interactions without compromising natural operation remains a key challenge. This reduces the reliability of human-to-robot transfer in contact-rich tasks. In this work, we present TacPrint, a wearable fingertip tactile sensor, where protrusions on the inner surface of the silicone skin are aligned one-to-one with 24 capacitive taxels to enable localized capacitive responses. A real-to-sim-to-real pipeline estimates a 35 $\times$ 26 contact-depth map from 24-channel capacitive signals. Against simulation-generated labels, the model achieved a contact-region RMSE of 0.223 $\pm$ 0.161 mm, a weighted-centroid error of 1.213 $\pm$ 2.379 pixels, and an IoU of 0.829 $\pm$ 0.169. With measured capacitive inputs, the network-predicted depth evaluated at the guide-calibrated contact center showed a mean absolute error of 0.085 $\pm$ 0.057 mm across all 40 controlled trials, while the mean contact-position error was 0.250 $\pm$ 0.208 mm across the 37 trials whose reference contact regions were not truncated by the sensing boundary. In human-to-robot replay, tactile-guided compensation increased grasping and wiping success rates from 0% to 91.67% and 90%, respectively. In closed-loop grasping, dense-depth feedback achieved success rates of 87.5% over all tested positions and 85% under edge-contact conditions, compared with 67.5% and 45% for raw-taxel feedback.

We present PinFT, a miniature five-axis capacitive force/torque sensor designed for direct tip-level integration into tweezer-like tools. The sensor employs a compact three-PCB stack with segmented plated through-hole electrodes and a silicone elastomer dielectric, enabling five-degree-of-freedom force and torque sensing ($F_x$, $F_y$, $F_z$, $T_x$, $T_y$) through displacement of a central 2,mm-diameter stainless steel pin. The fabricated prototype was calibrated using a higher-order polynomial mapping, yielding mean absolute errors of approximately 0.23,N for forces and 2.5,mN$\cdot$m for torques, with coefficients of determination ($R^2$) exceeding 0.97 across all axes. To demonstrate practical utility, a 3D-printed tweezer integrating PinFT sensors at both tips was mounted on a parallel-jaw gripper and evaluated across three representative manipulation tasks: grasping a sub-millimeter SMD capacitor, pulling a simulated hair from a silicone substrate, and tearing a compliant silicone specimen. In all cases, per-tip force sensing reliably captured characteristic force signatures that distinguish successful manipulation from failure events -- including slip and object ejection -- using gradient-based features derived from internal grasp force and net interaction force. These results demonstrate that direct, per-tip force sensing enables standard parallel-jaw grippers to monitor and interpret fine manipulation tasks performed through a handheld tweezer.

We present FlexiTac, a low-cost, open-source, and scalable piezoresistive tactile sensing solution designed for robotic end-effectors. FlexiTac is a practical "plug-in" module consisting of (i) thin, flexible tactile sensor pads that provide dense tactile signals and (ii) a compact multi-channel readout board that streams synchronized measurements for real-time control and large-scale data collection. FlexiTac pads adopt a sealed three-layer laminate stack (FPC-Velostat-FPC) with electrode patterns directly integrated into flexible printed circuits, substantially improving fabrication throughput and repeatability while maintaining mechanical compliance for deployment on both rigid and soft grippers. The readout electronics use widely available, low-cost components and stream tactile signals to a host computer at 100 Hz via serial communication. Across multiple configurations, including fingertip pads and larger tactile mats, FlexiTac can be mounted on diverse platforms without major mechanical redesign. We further show that FlexiTac supports modern tactile learning pipelines, including 3D visuo-tactile fusion for contact-aware decision making, cross-embodiment skill transfer, and real-to-sim-to-real fine-tuning with GPU-parallel tactile simulation. Our project page is available at https://flexitac.github.io/.