BiPathCPG: A Novel Load-Sharing Design Architecture for Compound Planetary Gearboxes
Organizations: Dept. of Cyber-Physical Systems, Indian Institute of Science, Bengaluru, India. · Dept. of Physics, Indian Institute of Technology Roorkee, India.
Abstract
Quasi-Direct Drive (QDD) actuators are widely used in legged robots due to their low reflected inertia, high backdrivability, and high torque density, commonly employing planetary or cycloidal gearboxes. Single-stage planetary gearboxes offer high efficiency but limited torque density; multi-stage designs improve torque density at the cost of efficiency; and cycloidal gearboxes provide high stiffness but suffer from torque ripple. Compound Planetary Gearboxes (CPG) offer a compromise, but conventional designs result in increased actuator width, mass, and reduced torsional stiffness in 3D-printed actuators. This paper proposes the BiPath Compound Planetary Gearbox (BiPathCPG), a novel architecture that introduces an idle second-stage sun gear and load-sharing second-stage planets within the otherwise unused space of a conventional CPG to simultaneously improve stiffness, reduce actuator width, and reduce mass. An optimization framework computes BiPathCPG parameters for a given motor and target gear ratio. The architecture is validated through a 3D-printed proof-of-concept actuator design, benchmarked against a conventional CPG using custom-built test rigs. The BiPathCPG achieves a torsional stiffness of 1394 Nm/rad, a 1.70x improvement over the conventional CPG, with a 32% reduction in backlash, 25 g lower mass, and approximately 6.4 mm reduction in axial width, while achieving a peak stall torque of 36.49 Nm.
Figures & tables
| Parameter | CPG | BiPathCPG |
| 14.00 | 14.00 | |
| (mm) | 0.6 | 0.6 |
| 18/66/33/117/– | 18/66/33/117/ 51 | |
| 3 | 3 | |
| is2/ip2 (mm) | 11.2/11.2/16.4/ 16.4/–/– | 11.2/11.2/ 10.2/ 10.2/10.2/8.2 † |
| (mm) | 87.10 | 80.94 |
| Actuator | Motor (Peak Torque) | Gearbox-type (gear material) | Ratio | Stiffness (N m/rad) | Backlash ¶ ( ∘ ) | Mass (g) | D L (Lg) (mm) | Exp. Peak Torque (N m) | Pred. Peak Torque ∗ (N m) |
| Roozing Cycloidal [ 20 ] | MN8012 (3.82 N m) | Cycloidal (PLA) | 11 | 633 | 0.35 | 809 | 42.02 | ||
| Roozing (Non-Pinwheel) [ 19 ] | MN8012 (3.82 N m) | Cycloidal (PA6-CF) | 11 | 1468 | 0.25 | 797 | 36.4 | 42.02 | |
| Roozing Anti-backlash [ 5 ] | RO100 (12 N m) | Cycloidal (PA6-CF) | 13 | 300 § | 0.647 § | 1350 | 156 | 156 | |
| Berkeley Humanoid Lite [ 3 ] | M6C12 (2.64 N m) | Cycloidal (PLA) | 15 | 319 | — | — | 39.60 | ||
| CY30 [ 7 ] | Maxon EC90 Flat (5.03 N m) | Cycloidal (PLA) | 30 | 641.4 | 942 † | — | 150.90 | ||
| COMPAct SSPG [ 23 ] | MN8014 (4.97 N m) | Planetary (single stage) (PLA) | 7.2 | 242.7 | 0.6 | 838 | — | 35.78 |
Robotics
Robotics studies the design and control of machines that perceive, move, and act in physical environments.
See all 801 papers