Organizations: Department of Mechanical Engineering, City University of Hong Kong, Hong Kong, China
Abstract
Artificial dynamic tactile sensing requires sensitivity, robustness, and compliance, yet existing technologies face trade-offs when scaling to large-area arrays, compounded by wiring complexity and cost. Here, we report a passive distributed paradigm using deep sub-wavelength acoustic waveguides that decouples performance from structural flexibility. Elastic-membrane-capped Helmholtz resonators interconnected by spring-reinforced microtubes form an enclosed network with invariant acoustic transmission under macroscopic bending. By sparsely embedding microphones, the system achieves real-time localization (4 mm highest spatial resolution; >99% accuracy in a 4 microphones 64-node sensing array) and waveform reconstruction of low-frequency signals (<100 Hz). Fast Continuous Wavelet Transform and a lightweight neural network enable inference within 5.5 ms. We demonstrate conformable prototypes-fingertip arrays, a tactile glove, and large-area skins-detecting stimuli from single-hair contact to 5-mg particle impacts, arterial pulse waves, feather touches, and finger contact. This establishes a scalable, flexible, low-cost paradigm for next-generation human-machine interfaces.
Tactile sensing is central to how robotic systems interact with the real world, yet current solutions face a tradeoff between sensing area and system complexity. This work investigates metallic ultrasound waveguides as distributed tactile sensors fully interrogated from a single proximal transducer. Using cylindrical indenters, we characterized the acoustic response to single and multi-point contacts with varying forces and contact materials. For single point indentation, the applied force was well captured by a linear relationship with the ratio of the reflection to transmission coefficients (F = a * R/T) across all nine tested materials (R2 >= 0.95). The calibration slope, a, correlated strongly with the material's effective contact modulus (log--log Pearson r=-0.98). The reflected energy partition was found to be a load-independent parameter related to the contacting material's properties, enabling material classification independent of force. For the two-indenter experiment, both contact forces were recovered from the waveguide signal and were in close agreement with reference load cell measurements (contact 1, R2 = 0.97; contact 2, R2=0.95). The approach was extended to two-dimensional metallic sheets, confirming both contact localization and material-dependent effects. Overall, these results validate metallic waveguides as a robust platform for distributed tactile sensing, providing contact localization, force estimation, and material-class discrimination for the contacting body.
We present FlexiTac, a low-cost, open-source, and scalable piezoresistive tactile sensing solution designed for robotic end-effectors. FlexiTac is a practical "plug-in" module consisting of (i) thin, flexible tactile sensor pads that provide dense tactile signals and (ii) a compact multi-channel readout board that streams synchronized measurements for real-time control and large-scale data collection. FlexiTac pads adopt a sealed three-layer laminate stack (FPC-Velostat-FPC) with electrode patterns directly integrated into flexible printed circuits, substantially improving fabrication throughput and repeatability while maintaining mechanical compliance for deployment on both rigid and soft grippers. The readout electronics use widely available, low-cost components and stream tactile signals to a host computer at 100 Hz via serial communication. Across multiple configurations, including fingertip pads and larger tactile mats, FlexiTac can be mounted on diverse platforms without major mechanical redesign. We further show that FlexiTac supports modern tactile learning pipelines, including 3D visuo-tactile fusion for contact-aware decision making, cross-embodiment skill transfer, and real-to-sim-to-real fine-tuning with GPU-parallel tactile simulation. Our project page is available at https://flexitac.github.io/.
We address the challenge of engineering distributed haptic displays capable of reproducing multiple localized, independently addressable vibrations -- representing virtual tactile pixels -- at arbitrary locations on a surface. Our technique is based on the focusing of mechanical waves in a flexural plate using a sparse set of actuators. At tactile frequencies, wave diffraction prevents the formation of localized virtual tactile pixels at spatial scales relevant for multi-digit touch interactions. We overcome this limitation by augmenting the plate with a lattice of mechanical resonators, forming a locally resonant metamaterial plate. Coupling between the plate's dynamic modes and those of the resonators alters the dispersion relation governing wave transmission, introducing a slow-wave branch that enables focusing beyond the diffraction limit imposed by the unmodified plate. We use numerical simulations to engineer the dispersion relation of the metamaterial system for high-resolution focusing at tactile frequencies. We then fabricate a metamaterial tactile display and experimentally demonstrate virtual pixels that are far more localized than those generated on an otherwise identical plate without resonators, resulting in a tenfold reduction in virtual-pixel area. In behavioral experiments, we show that this system can deliver perceptually localized single- and multi-point tactile feedback and moving tactile sources while maintaining independent control over temporal waveforms at multiple display locations. The methods reported here can enable high-resolution haptic displays for widespread applications using a small number of actuated degrees of freedom.