Electric joint systems are significant elements of an underwater manipulator for its actuation, drive, and control. Working in an underwater environment, the joints suffer huge ambient pressure. To withstand it, the pressure compensation method is usually deployed, whereas the pressurized oil introduces sealing problems as well as parametric uncertainties and unknown disturbances for the dynamic model of the joint. To tackle these issues, this study proposes a design framework for the underwater oil-filled electric joint. The dynamics of the pressure compensation module is analyzed and the structure of the joint is optimized to seal the internal hydraulic oil. An uncertainty dynamic model of the oil-filled joint is established and a robust position controller is designed based on the structured singular value synthesis (mu-synthesis). Experimental results validate the feasibility of the proposed methods.
Robot sensors and electronic equipment are prone to failure in harsh environments. With water hydraulic drive, thin and long tubes enable remote operation without actuator-side sensors. Furthermore, the elasticity of the tubes reduces the impedance of the joints (actuators), benefiting robot tasks involving unexpected contact with the environment or vibrations. However, owing to the low impedance and limited camera visibility, accurately positioning the joint (or end effector) to the target location under varying load conditions is challenging. This study proposes a novel method that employs water-filled flexible tubes to enable the transmission of driving power and actuator-side information to and from the actuator, respectively, without actuator-side sensors. By modeling volumetric loss during transmission based on pressure fluctuations and incorporating minor air entrapment, simultaneous power transmission and position estimation is achieved through a tube up to 50 m. Thus, it becomes possible to use a feedback control framework that was previously difficult to implement in sensorless systems. Experimental validation confirms stable position control of a sensorless water hydraulic cylinder under varying loads. Furthermore, a field parameter-identification method accounts for tube and air entrainment variability without requiring actuator-side sensors. These contributions promote reliable remote control of robots in harsh environments.
Underwater robots are widely deployed for ocean exploration and manipulation. Underactuated mechanisms are advantageous in aquatic environments because reducing actuator count lowers motor-leakage risk while introducing inherent mechanical compliance. However, accurate modeling of underwater underactuated and soft robotic systems remains challenging, as it requires identifying high-dimensional structural and hydrodynamic parameters. In this work, we propose a trajectory-driven global optimization framework for unified structural-hydrodynamic modeling of underwater multibody systems. Inspired by the Covariance Matrix Adaptation Evolution Strategy (CMA-ES), the proposed approach simultaneously identifies coupled elastic, damping, and distributed hydrodynamic parameters through trajectory-level matching between simulated and experimental motion. This enables high-fidelity reproduction of underactuated mechanisms and compliant soft robotic systems in underwater environments, using as little as a single video recording. We first validate the framework on a link-by-link underactuated multibody mechanism, demonstrating accurate identification of distributed hydrodynamic coefficients, with normalized end-effector position error below 5% across multiple trajectories, initial conditions, and both active-passive and fully passive configurations. The modeling strategy is further validated on an asymmetric octopus-inspired soft arm, confirming its effectiveness for compliant soft robotic systems. Finally, eight identified arms are assembled into a swimming octopus robot, where the unified parameter set enables realistic whole-body behavior without additional retuning. These results demonstrate the scalability and transferability of the proposed structural-hydrodynamic modeling framework across underwater underactuated and soft robotic systems.
Continuum manipulators mounted on multi-rotor UAVs enable compliant aerial manipulation, but payloads and propeller downwash amplify out-of-plane bending and twisting that degrade end-effector pose accuracy. To address this problem, we present a universal-joint-based continuum manipulator designed to improve resistance to out-of-plane deformation during aerial manipulation. The proposed design uses a tubular backbone with spring-reinforced universal joints and an integrated conduit for internal routing and fluid delivery. We evaluate the design in still air and under peak propeller downwash across varying payloads, and benchmark it against a prior Nitinol-backbone CM. Bench tests show improved resistance to out-of-plane deformation across all conditions. Under peak downwash, the proposed design reduces mean error by 2.5-4x in yaw, 2-45x in y-axis, and up to 5x in roll compared to the NiTi-backbone design. We further analyze hover stability through in-flight coupled-disturbance tests over varying payloads and actuation speeds, and demonstrate the system in water sampling, spot spraying, and object transport.