Enhancing Balance and Posture in Material Handling Tasks with a Wearable Robotic Tail
Authors: Eisa Anwar, Sajeeva Abeywardena, Stuart C. Miller, Ildar Farkhatdinov
Organizations: Faculty of Natural, Mathematical and Engineering Sciences, King’s College London, London, UK. · School of Electronic Engineering and Computer Science, Queen Mary University of London, London, UK. · School of Mechanical Engineering Sciences, University of Surrey, UK. · William Harvey Research Institute, Queen Mary University of London, London, UK. · School of Biomedical Engineering and Imaging Sciences, King’s College London, London, UK
Frequent heavy lifting is linked to musculoskeletal strain, with lower back pain affecting up to 40% of manual labourers. Inspired by animals using tails for balance, we developed a wearable robotic tail as a dynamic counterbalance. Ten participants performed an imitated shelf loading/unloading task across three conditions: active tail, passive tail, and no tail. Kinematics, centre of pressure, and muscle activation (gastrocnemius, erector spinae, tibialis anterior, biceps brachii) were measured. Compared with no tail, the active tail achieved >20 mm reduction in centre of pressure peak displacement, 4.3 degree reduction in trunk motion, and >9% and >20% reductions in erector spinae and gastrocnemius activity, respectively. The passive tail produced smaller reductions, suggesting passive counterbalancing helps while active movement augments it further. Biceps brachii activation increased with the active versus passive tail. The ankle kinematics and tibialis anterior activation were unchanged. These findings support wearable robotic tails for improving balance during material handling.
Figures & tables
Figure 1: Robotic tail The custom built wearable robot tail worn by a user during object handling task.
Figure 2: Centre of Pressure (CoP) Analysis. ( A ) CoP change for one participant for the placement and retrieval trials for all conditions of the experiment. The blue, green, and orange lines represent the active tail (ACT), passive tail (PAS), and without tail (WOUT) conditions respectively, while the static standing (STND) trial is shown in yellow. The grey lines at the top and bottom of the figure mark the boundaries of the BoS (i.e., the front and back of the feet). ( B ) Peak displacement and RoM of the sagittal CoP for all participants. Each participant is represented by a single colour, and each point represents the average of all their repetitions for a single condition. The percentage changes of the statistically significant results are stated, and asterisks indicate the significance level: *( p<0.05 ), **( p<0.01 ), ***( p<0.001 ).
Figure 3: Trunk and ankle inclination (i.e. flexion/extension). ( A ) Single participant for the placement and retrieval trials for all conditions of the experiment. The single yellow line represents the static standing baseline result and the three other colours with multiple repetitions represent the three different conditions. ( B ) Trunk and ankle inclination for all participants. Each participant is represented by a single colour, and each point represents the average of all their repetitions for a single condition. Dotted lines link a single participant across their experimental conditions. The percentage values of the statistically significant results are shown under respective graphs.
Figure 4: Muscle Activity Data. ( A ) Muscle activity of one participant for all conditions and repetitions. The left four graphs are for each of the four recorded muscles for the placement task and the right four graphs are for the retrieval task. ( B ) Muscle activity for all participants for all conditions. Each condition’s repetitions are averaged for each individual point. The data is split into four rows with two columns. The left graphs are for placement and the right graphs are for retrieval tasks. Each row corresponds to one of the four muscles tested: biceps brachii (BB), erector spinae (ES), gastrocnemius (GS) and tibialis anterior (TA). Each section of the three graphs consists of peak activity, average activity and iEMG result.
Figure 5: Experimental Setup. ( A ) The setup of the experiment and the sensors used. The light blue circles are motion tracking markers, the darker blue rectangles are electromyography sensors (EMG), and the dark blue line the figure is standing on is a force plate. ( B ) The experimental procedure consisting of two tasks. ( C ) The experiment was carried out in three conditions: with the tail powered and active (ACT), with the tail unpowered and passive (PAS), and without the tail (WOUT).