cs.RONov 12, 2026

Direct-Ink-Writing of Soft Thin Film Force-Sensitive Resistors with Velostat and Printed-Carbon Sensing Elements

Authors: Mostafa Mo. Massoud, Paulo H. T. F Alves, Timothy Kennedy, Jacqueline Libby

Organizations: Department of Mechanical Engineering, Stevens Institute of Technology, Hoboken, NJ 07030 USA

Abstract

Flexible resistive force sensors are useful for wearable, rehabilitation, and human--machine interfaces, but their performance depends on sensing-material architecture and fabrication. This work presents a parameterized Voltera NOVA-based direct-ink-writing workflow using printed silver electrodes with multilayer Velostat sensing elements on PET and TPU substrates, together with an exploratory fully printed carbon architecture. Velostat sensors containing 1, 2, 4, and 6 sensing layers exhibited strongly nonlinear force--voltage responses, with the greatest sensitivity at low forces. Best-fit straight-line R2R^2 values ranged from 0.475 to 0.641, area-based hysteresis from 3.90% to 7.47%, and 5-min voltage drift from 1.9% to 7.3%, with no consistent monotonic relationship between layer count and these metrics. Selected PET6 and TPU6 devices showed less than 0.05V change in peak output between the first and final 100 cycles of a 10,000-cycle test. Printed-carbon devices demonstrated the feasibility of a more fully printed architecture, but configurations with six or fewer layers saturated below approximately 0.5N or were nonfunctional, while the eight-layer device responded primarily below approximately 2~N. These results establish the feasibility of the printed-electrode Velostat workflow while identifying printed sensing materials as a key area for further development.

Figures & tables

Explore similar work

Mar 18, 2026

Multi-material Direct Ink Writing and Embroidery for Stretchable Wearable Sensors

The development of wearable sensing systems for sports performance tracking, rehabilitation, and injury prevention has driven growing demand for smart garments that combine comfort, durability, and accurate motion detection. This paper presents a textile-compatible fabrication workflow that integrates multi-material direct ink writing with automated embroidery to create stretchable strain sensors directly embedded into garments. The process combines sequential multi-material printing of a silicone-carbon grease-silicone stack with automated embroidery that provides both mechanical fixation and electrical interfacing in a single step. The resulting hybrid sensor demonstrates stretchability up to 120% strain while maintaining electrical continuity, with approximately linear behaviour up to 60% strain (R^2 = 0.99), a gauge factor of 31.4, and hysteresis of 22.9%. Repeated loading-unloading tests over 80 cycles show baseline and peak drift of 0.135% and 0.236% per cycle, respectively, indicating moderate cycle-to-cycle stability. Mechanical testing further confirms that the silicone-fabric interface remains intact under large deformation, with failure occurring in the textile rather than at the stitched boundary. As a preliminary proof of concept, the sensor was integrated into wearable elbow and knee sleeves for joint angle monitoring, showing a clear correlation between normalised resistance change and bending angle. By addressing both mechanical fixation and electrical interfacing through embroidery-based integration, this approach provides a reproducible and scalable pathway for incorporating printed stretchable electronics into textile systems for motion capture and soft robotic applications.
Aug 14, 2026

Effect of Twisted-Yarn Architecture on Pressure and Proximity Sensing Characteristics of Textile Capacitive Sensors for Robotic Skin

Textile-integrated capacitive sensors offer flexible and conformable tactile sensing for wearable electronics and human-robot interaction; however, the influence of yarn-level architecture on capacitive transduction characteristics remains insufficiently quantified. This work presents a textile capacitive sensing platform based on silver-coated yarns coated with polydimethylsiloxane and assembled into one-, two-, and four-layer twisted configurations. The influence of effective electrode overlap area and inter-fiber separation on the capacitive response is systematically investigated, enabling architecture-dependent tuning of pressure and proximity sensing characteristics. Pressure was calculated using the localized single-fiber contact area, corresponding to stresses of 0.4-3.9 MPa. Increasing the layer number improved mechanical strength and sensing performance: elongation at break increased from 37.5% to 62.5% and 85.0%, while the maximum load increased from 23.3 to 42.7 and 89.7 N. Sensitivity increased with layer number and frequency, reaching 0.1331 MPa−1^{-1} for the four-layer sensor at 100 kHz. The four-layer configuration also exhibited low hysteresis, minimal thermal drift from 25 to 90 ∘^\circC, and stable operation over 15,000 cycles. Proximity detection ranges of 60, 50, and 40 mm were obtained for the one-, two-, and four-layer sensors, respectively, revealing an architecture-dependent sensitivity-range trade-off. A 4×\times4 textile sensing array enabled spatial contact mapping, while robotic-arm integration demonstrated real-time touch and proximity detection with an end-to-end robotic system latency (from detection to robot reaction) of 403 ms. The results establish yarn architecture as a tunable design parameter governing the measurement characteristics of textile-integrated capacitive sensing systems.
Oct 22, 2026

VecTile: A Low-Cost Flexible Tactile Array for 3-DoF Force Sensing

Tactile sensing provides robots with contact information difficult to obtain from vision alone. Shear force is particularly important for understanding tangential contact, guiding corrective motions, and maintaining grasp stability, yet flexible and low-cost tactile arrays often measure only normal force. We introduce VecTile, a low-cost, 6 mm thin, flexible tactile array capable of three-axis force sensing. VecTile combines a piezoresistive layer with passive silicone nubs that convert normal and shear forces into distinguishable pressure patterns. The sensor can be fabricated in-house without specialized equipment. The complete system costs less than 35 USD for a 4x4 array. We validate the sensing mechanism through finite element analysis and hardware experiments. In controlled single-taxel tests over 1-5 N normal force and up to 1.5 N shear force, VecTile achieves root-mean-square errors of 0.39 N and 0.16 N for normal and shear forces. A VecTile calibrated while flat retains accuracy when curved, while a five-minute manual calibration is sufficient for practical use. Two applications demonstrate its utility. First, shear readings are sensitive enough to stop a sharp scalpel from puncturing a balloon after contact. Second, the sensor substantially improves Diffusion Policy-guided power-plug insertion. All designs and code will be released upon paper acceptance. Project website: https://jiannnh.github.io/VecTile/.