RESCUE Jumper: A Centimeter-Scale Rolling and Jumping Robot for Search and Rescue
Authors: Kiran Marques, Shashwat Singh, Ben D'Ambrosia, Zeynep Temel, Melisa Orta Martinez
Organizations: Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213, USA. · The Robotics Institute, Carnegie Mellon University, Pittsburgh, PA 15213, USA. · University of Pittsburgh, PA 15260, USA.
Centimeter-scale robots are promising for urban search and rescue because they can enter confined spaces that are inaccessible or unsafe for humans. However, their small size limits obstacle traversal after deployment. This paper presents the RESCUE Jumper, a 125 g mobile robot with a 6.2 cm width and 6.2 cm diameter wheels that combines ground rolling with jumping to traverse steps and gaps that exceeds its rolling capability. The RESCUE Jumper uses its two actuators for both rolling mode and jumping by reversing the direction of wheel motion. Forward wheel motion enables rolling, while reverse wheel motion winds a spring steel tail to store elastic potential energy and release it for jumping. The RESCUE Jumper varies tail winding speed to control jump direction, transitioning from backward to forward jumps as winding speed increases from 0.75 rad/s to 8.73 rad/s. The launch angle of the jumps ranges from 45 degree to -11 degree with respect to the vertical axis, reaching a maximum height of 9.2 cm and a maximum lateral displacement of 11.2 cm. We model the winding speed-dependent jumping behavior in three phases: tail release to determine the contact point and robot orientation, tail straightening until liftoff, and ballistic flight to predict jump height and lateral displacement. Finally, qualitative tests highlight the robot's locomotion in cluttered, real-world environments. The model and experiments presented in this work can inform future designs of space-constrained jump mechanisms in centimeter-scale robots for search and rescue and inspection in unstructured environments.
Figures & tables
Fig. 1 : (A) The RESCUE Jumper measures 6.2cm wide with 6.2cm diameter wheels and is about the size of a tennis ball. It is able to jump (B) backward or (C) forward by varying the winding speed of the tail. Numbers 1, 2, and 3 indicate jump progress, and CR shows the center of rotation.
Fig. 2 : RESCUE Jumper system packaging. A 3D-printed inner body, chassis, and clamp support the tail, motors, and drivetrain. Two adjacent motors drive coaxial wheels, while three PCBs and two batteries are arranged around the core.
Fig. 3 : (A) The jumping mechanism consists of rods attached to the wheels and passive flexure gates on the spring-steel tail. (B) During forward drive, (1) the rods rotate with the wheels, (2) the flexure gates bend, and (3) the rods pass underneath the tail, allowing the robot to advance. (C) During reverse drive, (1) the robot rolls into the pre-jump orientation, (2) the wheel rods catch the tail after passing over the flexure gates, (3) the rods wind the spring-steel tail to store elastic energy, and (4) the end of the tail reaches the rods, releasing the tail and generating the jump.
Symbol
Description
Units
E
Spring steel elastic modulus
Pa
L
Tail length
m
w
Tail width
m
d
Tail thickness
m
Itail
Tail area moment of inertia
m 4
λ
Linear density of tail
kg/m
TABLE I : System parameters
Fig. 4 : A) Initial configuration. The center of rotation (CR), center of gravity (CG), and anchor point A are on the inner body of the robot. The rod is attached to the wheel. Initial position vectors are panchor , prod , and pCG . B) Winding configuration with robot orientation, ϕ , and constant rod offset, ϕrod . The tail length, L , is the sum of the length wrapped around the inner body, Lwrapped , a constant length from the wrapped portion to the rods, Lconst , and a remaining length past the rods, Lrem .
Fig. 5 : A) The inner body rotates at ωwind with respect to the wheels, causing displacement θinner . B) After the CG passes the negative vertical axis, it applies a CCW torque to the system, causing displacement θouter . The rod is at prod2 . The wrapped portion of tail meets the free portion at pt .
Fig. 6 : Tail straightening ( ωwind= 2.16 rad/s) from (A) the moment ptail contacts the ground to (C) liftoff can be modeled using (D) an elastica beam for the tail adapted from Timoshenko and Gere [ 18 ] to include both Px , Py , and θtarget=0 .
State
Governing Equation
O
A
x
dx/ds
=cos(θ)
0
xa
y
dy/ds
=sin(θ)
0
ya
θ
dθ/ds
=M/(EI)
NK
ϕ−π
M
dM/ds
=−Pxsin(θ)+Pycos(θ)
0
NK
Px
dPx/ds
=0
NK
NK
Py
dPy/ds
=0
NK
NK
TABLE II : State variables, governing equations, and boundary constraints for the tail with O pinned and A fixed.
Fig. 7 : Damping parameters mag and ratio affect Py on the robot. Low damping (left) (mag = 0 , ratio = 0 ) reaches liftoff ( Py=0 ) prematurely. Moderate damping (middle) (mag = 6.2 , ratio = 2.4 ) best matches the experimentally observed motion of the robot. High damping (right) (mag = 12.4 , ratio = 4.8 ) causes oscillations in Py=0 that never reach liftoff.
Fig. 8 : Robot jumps onto a 5cm step from gravel after failing to traverse it by rolling. (A) The robot starts from its initial position, (B) reorients and winds the tail, (C) jumps onto the step, (D) lands on the ledge, and (E) continues rolling forward.
Fig. 9 : Phase 1, Phase 2, Phase 3 outputs evaluate the model per phase. The overall model pipeline from a given input ωwind predicts a jump described by [liftoff direction, ypeak , xend ] with RMSE = [ 21.2\SIUnitSymbolDegree , 13.5mm , 57.2mm ].
We present a rolling and jumping underactuated monopedal robot designed to explore multimodal locomotion on low-gravity bodies. It uses only two reaction wheels to control its spatial orientation with two controllers: a balancing controller which can aim the robot's jump direction on the ground, and an aerial reorientation controller which can aim the robot's leg for landing after flight. We demonstrate rolling, targeted jumping and landing, and self-righting using only three actuators total, keeping system size to 0.33m and 1.25kg. Simple switching between locomotion modes enables the system to deal with differing landscapes and environmental conditions.
Neil R. Wagner, Justin K. Yim
Department of Mechanical Science and Engineering, University of Illinois Urbana-Champaign
Quadrupedal wheeled-legged robots combine the advantages of legged and wheeled locomotion to achieve superior mobility, but executing dynamic jumps remains a significant challenge due to the additional degrees of freedom introduced by wheeled legs. This paper develops a mini-sized wheeled-legged robot for agile motion and presents a novel motion control framework that integrates the Nonlinear Model Predictive Control (NMPC) for locomotion and the Differential Evolution (DE) based trajectory optimization for jumping in quadrupedal wheeled-legged robots. The proposed controller utilizes wheel motion and locomotion to enhance jumping performance, achieving versatile maneuvers such as vertical jumping, forward jumping, and backflips. Extensive simulations and real-world experiments validate the effectiveness of the framework, demonstrating a forward jump over a 0.12 m obstacle and a vertical jump reaching 0.5 m.
Xuanqi Zeng, Lingwei Zhang, Linzhu Yue +4
Department of Mechanical and Automation Engineering, The Chinese University of Hong Kong
We demonstrate a jumping robot that reaches high (7.6 m) and fast (190 ms stance time) jumps from a single long leg driven by a direct-drive transmission, without elastic energy storage. At 281 g, it achieves the highest jump yet reported for an electrically actuated, spring-free system. The leg uses a new fabric-wrap transmission that provides a variable mechanical advantage, keeping a small electric motor near its peak power output through the stroke while bracing the long, lightweight leg against buckling. A balancing module at the top of the leg uses small propellers to control the leg's orientation on the ground and in the air, where the long leg provides a large moment arm for the control torques. The robot is validated outdoors with vertical jumps, attitude control on the ground and in flight, and tilted jumps.
Gihyeok Na, Justin K. Yim
Department of Mechanical Science and Engineering, University of Illinois Urbana-Champaign, IL 61801 USA