Organizations: Institute for Interdisciplinary Information Sciences, Tsinghua University; Beijing, China. · Pokebot Inc.; Beijing, China. · School of Electronic Information and Communications, Huazhong University of Science and Technology; Wuhan, China. · Shanghai Qi Zhi Institute; Shanghai, China.
Human touch depends on the integration of shape, stiffness, and friction, yet existing tactile displays cannot render these cues together as continuously tunable, high-fidelity signals for intuitive perception. We present ArrayTac, a closed-loop piezoelectric tactile display that simultaneously renders these three dimensions with continuous tunability on a 4 by 4 actuator array. Each unit integrates a three-stage micro-lever amplifier with end-effector Hall-effect feedback, enabling up to 5 mm displacement, greater than 500 Hz array refresh, and 123 Hz closed-loop bandwidth. In psychophysical experiments, naive participants identified three-dimensional shapes and distinguished multiple stiffness and friction levels through touch alone without training. We further demonstrate image-to-touch rendering from an RGB image and remote palpation of a medical-grade breast tumor phantom over 1,000 km, in which all 11 naive participants correctly identified tumor number and type with sub-centimeter localization error. These results establish ArrayTac as a platform for multidimensional haptic rendering and interaction.
We present FlexiTac, a low-cost, open-source, and scalable piezoresistive tactile sensing solution designed for robotic end-effectors. FlexiTac is a practical "plug-in" module consisting of (i) thin, flexible tactile sensor pads that provide dense tactile signals and (ii) a compact multi-channel readout board that streams synchronized measurements for real-time control and large-scale data collection. FlexiTac pads adopt a sealed three-layer laminate stack (FPC-Velostat-FPC) with electrode patterns directly integrated into flexible printed circuits, substantially improving fabrication throughput and repeatability while maintaining mechanical compliance for deployment on both rigid and soft grippers. The readout electronics use widely available, low-cost components and stream tactile signals to a host computer at 100 Hz via serial communication. Across multiple configurations, including fingertip pads and larger tactile mats, FlexiTac can be mounted on diverse platforms without major mechanical redesign. We further show that FlexiTac supports modern tactile learning pipelines, including 3D visuo-tactile fusion for contact-aware decision making, cross-embodiment skill transfer, and real-to-sim-to-real fine-tuning with GPU-parallel tactile simulation. Our project page is available at https://flexitac.github.io/.
Humanoid hands require tactile feedback across the whole finger, not just the fingertip, to grasp and manipulate objects properly. Vision and proprioception alone cannot reliably provide this information, particularly when the hand's own fingers occlude the camera's view of the grasp. We present a low-cost tactile array for a humanoid finger, made from Velostat and conductive tape. The fingertip carries seven contact points including a 2x3 matrix wrapped across its front, left, and right faces, and a separate contact point at the tip. The proximal and middle phalanges each carry a single front-facing contact line. We measure the sensor's hysteresis and recovery time after release, through repeated loading and press-release tests. We also test a compliant, 3D-printed contact structure with a gap and a bump, inspired by similar designs in prior work, and show it cuts recovery time by 74% compared to a flush-contact baseline. We then show the sensor can produce distinct activation patterns for different contact geometries (flat, edge, corner) at the fingertip, and that it registers contact across all three phalanges during a grip. Finally, we discuss the limits of our fabrication changes and point to software-based compensation as a promising way to more directly fix the remaining hysteresis in the future.
Neel Adwani, Muhaiminul Islam Akash, Rituja Bhattacharya +1
New Jersey Institute of Technology (NJIT), Electrical and Computer Engineering
Resistive pressure arrays are the cheapest and most widely shipped tactile sensors, yet tactile representation learning has concentrated on optical sensors that image a deforming gel. We present Tactus, an open model that answers text queries from pressure data alone: on the STAG benchmark (27 objects, held-out recordings), it reaches 0.771 +/- 0.062 top-1 over four runs (top-3 0.935), matching, and at best exceeding, the dataset's supervised closed-set CNN at 0.76, with no trained classifier head. The recipe is small-data: 187 training recordings, masked-autoencoder pretraining on 144k unlabeled same-sensor frames, and the sensor's own calibration affine, which recovered more accuracy than every architecture change combined. The released model's errors concentrate in a few contact-ambiguous classes, are uncorrelated with text-target geometry (Spearman rho <= 0.05 over 702 class pairs), and survive paraphrased and even bare-name queries within one point; two diverse frames recover 89% of eight-frame accuracy. Failures are reported with equal precision: cross-sensor pretraining pooling gave no gain, vision co-training degraded touch, and a mis-normalized input pipeline silently discarded 97% of the sensor's dynamic range while producing plausible intermediate results. Weights, code, and the memory layer the model plugs into are released openly.