This paper presents Delta6, a low-cost, six-degree-of-freedom (6-DOF) force/torque end-effector that combines antagonistic springs with magnetic encoders to deliver accurate wrench sensing while remaining as simple to assemble as flat-pack furniture. A fully 3D-printed prototype, assembled entirely from off-the-shelf parts, withstands peak forces above +/-14.4 N and torques of +/-0.33 N.m per axis; these limits can be further extended by leveraging the proposed parametric analytical model. Without calibration, Delta6 attains a 99th-percentile error of 7% full scale (FS). With lightweight sequence models, the error is reduced to 3.8% FS by the best-performing network. Benchmarks on multiple computing platforms confirm that the device's bandwidth is adjustable, enabling balanced trade-offs among update rate, accuracy, and cost, while durability, thermal drift, and zero-calibration tests confirm its robustness. With Delta6 mounted on a robot arm governed by a force-impedance controller, the system successfully performs two contact-rich tasks: buffing curved surfaces and tight assemblies. Experiments validate the design, showing that Delta6 is a robust, low-cost alternative to existing 6-DOF force sensing solutions. Open-source site: https://wings-robotics.github.io/delta6 .
Existing bilateral teleoperation platforms still rely on costly rigid six-axis force/torque sensors, tightly coupled leader-follower hardware, and kilohertz control loops. We present a Cartesian bilateral framework built on the hardware-agnostic WinGs Operating Studio (WOS) middleware, in which a low-cost compliant 6-DOF pose-and-force sensing end-effector, Delta6, is mounted on both sides so that each manipulator behaves as an end-effector 6-DOF series elastic actuator (SEA). The leader runs a damping-only admittance loop with a 6-D biquad notch filter; the follower realizes a stiffness-damping impedance through a position-based outer loop with a PID wrench-to-pose mapping. Three time scales (hardware I/O, mid-rate impedance/admittance, low-rate teleoperation messages) are explicitly decoupled, enabling the same application to drive heterogeneous arms. On a Lite6/FR3 testbed at 150 Hz, the system tracks stably under delays up to 120±40 ms and 1% packet loss, matches the prescribed virtual stiffness in contact, and shows a favorable cumulative energy signature in passivity-style tests.
Yue Feng, Weicheng Huang, I-Ming Chen
Robotics Research Centre Nanyang Technological University Singapore · WinGs Robotic USA
We introduce CoinFT, a capacitive 6-axis force/torque (F/T) sensor that is compact, light, low-cost, and robust with an average root-mean-squared error of 0.16 N for force and 1.08 mN m for moment when the input ranges from 0-14 N and 0-5 N in normal and shear directions, respectively. CoinFT is a stack of two rigid PCBs with comb-shaped electrodes connected by an array of silicone rubber pillars. A microcontroller interrogates the electrodes in different subsets in order to enhance sensitivity for measuring 6-axis F/T. The combination of features of CoinFT enables various contact-rich robot interactions across different embodiment domains including drones, robot end-effectors, and wearable haptic devices. We demonstrate the utility of CoinFT through two representative applications: a multi-axial contact-probing experiment in which a CoinFT mounted beneath a hemispherical fingertip measures 6-axis force and torque representative of manipulation scenarios, and a force-control task on a drone. The design, fabrication, and firmware of CoinFT are open-sourced at https://coin-ft.github.io/.
Hojung Choi, Jun En Low, Tae Myung Huh +7
Stanford University, CA, USA. · University of California Santa Cruz, CA, USA. · Reality Labs Research, Meta Platforms Inc, WA, USA.
Tactile sensing provides robots with contact information difficult to obtain from vision alone. Shear force is particularly important for understanding tangential contact, guiding corrective motions, and maintaining grasp stability, yet flexible and low-cost tactile arrays often measure only normal force. We introduce VecTile, a low-cost, 6 mm thin, flexible tactile array capable of three-axis force sensing. VecTile combines a piezoresistive layer with passive silicone nubs that convert normal and shear forces into distinguishable pressure patterns. The sensor can be fabricated in-house without specialized equipment. The complete system costs less than 35 USD for a 4x4 array. We validate the sensing mechanism through finite element analysis and hardware experiments. In controlled single-taxel tests over 1-5 N normal force and up to 1.5 N shear force, VecTile achieves root-mean-square errors of 0.39 N and 0.16 N for normal and shear forces. A VecTile calibrated while flat retains accuracy when curved, while a five-minute manual calibration is sufficient for practical use. Two applications demonstrate its utility. First, shear readings are sensitive enough to stop a sharp scalpel from puncturing a balloon after contact. Second, the sensor substantially improves Diffusion Policy-guided power-plug insertion. All designs and code will be released upon paper acceptance. Project website: https://jiannnh.github.io/VecTile/.
Jian Hou, Xin Zhou, Adam J. Spiers
All authors are with the Manipulation and Touch Lab, Dept. Electrical and Electronic Engineering, Imperial College London.