At the water-land interface, amphibious fishes encounter wet flowable substrates made of granular solid-water mixtures, which can stay solid or flow like a fluid. As these substrates become wetter or drier, their yield strength (at which solid-fluid transition occurs) and cohesion (how sticky they are) both change, challenging locomotion. Despite substantial understanding of tetrapod locomotion on flowable substrates (mostly dry sand), we know little about how amphibious fishes cope with wet flowable substrates of various wetness. Here, we studied mudskippers on clay mud of controlled, variable wetness over the range where solid-fluid transition occurs. As mud became wetter, its strength decreased by 100-fold, leading the animal to sink deeper, with larger areas of body and fins contacting mud. By contrast, mud stuck most easily at intermediate wetness. The increased sinkage and contact and stickiness change caused more mud to stick to and pull against the animal on wetter mud. We also tested dry mud, which stuck to animal fins as its mucus dried. Despite these challenges, the mudskipper predominately used a conserved crutching gait on all except the wettest mud tested, with a modest performance reduction. When normal crutching became less effective, the animal assisted it with tail thrusting, by bending and straightening it to push downward and backward to generate additional thrust and lift, or even thrusting the tail to jump. These observations suggest that mudskipper's crutching motor program is well adapted to its native muddy substrates but inflexible, with most novelty in tail use.
Animals and robots encounter mud at the water-land interface. Like sand, mud can stay solid or flow like a fluid. Unlike sand, the yield strength of mud at which solid-fluid transitions occur depends on not only the amount of solid relative to fluid (water in mud, air in dry sand), but also how much coarse grains and fine clay are within the solid. Despite understanding of locomotion on/within dry sand dominated by coarse grains with repulsive normal forces and friction, little is known for mud dominated by fine clay with strong cohesion. Here, we developed methods to prepare uniform mud of controlled, variable yield strength and characterize and track its drift from water evaporation. Compared to other flowable substrates, mud strength measured by upward force during penetration is weaker and can vary more, and mud sticks more during extraction to pull downward, making it more challenging for locomotion.
Low-friction surfaces challenge bipedal locomotion by limiting the contact forces available during stepping. Inspired by penguin waddling, we investigate how lateral torso motion and center of mass (COM) placement affect locomotion as surface friction changes. Using a five-actuator biped, we compare an upright-gait strategy with a penguin-inspired torso-over-stance-leg strategy across multiple COM placements in simulation and hardware. In the 3-D simulator MuJoCo, we sweep through sinusoidal leg and hip actuation parameters across four friction coefficients mu = 0.1, 0.3, 0.5, 0.7. In simulation, torso-over-stance-leg motion produces more successful controllers and higher forward speeds at low friction, with the highest speed occurring for the high-COM configuration. Hardware experiments show the same low-friction speed trend: at mu=0.12, torso-over-stance-leg motion increases forward speed and reduces cost of transport at both tested COM ratios, and the higher COM also improves both measures. The high-COM penguin configuration is the fastest and most energy efficient while maintaining low sideways foot motion. At mu=0.45, the COM trend reverses: the lower-COM configurations are faster and more energy efficient, while gait strategy has little effect on forward speed but still changes sideways foot motion. These results show that the effects of lateral torso motion and COM placement depend on the available friction, and that forward speed, energy use, and slip-related foot motion can be modulated with a penguin-inspired torso motion on hardware.
Bipedal robots are challenging to control because they operate close to instability, where small variations in foot-terrain contact can rapidly destabilize locomotion. On rigid terrain, bipedal robots mitigate this fragility by using well-established contact mechanics and control strategies. On flowable surfaces such as granular slopes, foot contact can induce large surface deformations and solid-fluid-like transitions, coupling terrain effects with robot dynamics, leading to underperformance or failure. This is partly due to the lack of reliable methods to represent the dynamics of flowable terrain, making it difficult to account for terrain effects in locomotion design. Here, we investigate how controlling terrain response can improve bipedal locomotion on granular slopes by studying the terradynamics of cleated feet, thin plates emanating from the foot soles. Systematic studies of a small-scale (1.4 kg) robophysical biped reveal that cleats with sparse and dense spacing lead to excessive terrain yielding and resistance, respectively, degrading performance and leading to failure. An intermediate cleat spacing distributes interaction forces to maintain substrate stresses near (or below) the yield threshold, enabling walking on granular slopes up to 30 degrees. Guided by these principles, we design a foot that actively adjusts cleat depth and accommodates both rigid and granular terrain. We also demonstrate that the principles of effective foot-terrain interaction translate to a larger (15 kg) autonomous biped. Our study presents an alternative to conventional body-centric robot control approaches, which regulate terrain-induced effects through body motion, by instead regulating terrain interactions through limb-centric approach.
Deniz Kerimoglu, Junnosuke Kamohara, Jiyeon Maeng +4