cs.RONov 2, 2026

Exploring Proximity and Tactile Sensing for Robotic Manipulation

Authors: Eric T. Chang, Bianca Aumann, Zhanpeng He, Mohamed Elnoor, Thomas Liang, Matei Ciocarlie, Nima Fazeli, Joshua Migdal, 

Organizations: Amazon Robotics, MA, USA. · Mechanical Engineering Department, Columbia University, NY, USA.

Abstract

Pre-touch sensing, or sensing information about an object before contact, is an attractive modality for robot hands as it can allow a robot to anticipate and respond to a contact before it happens. In this work, we introduce ToFTouch, a multimodal tactile sensor combining three multizone (4×\times4 resolution) time-of-flight sensors with an optics-based pressure sensing array. We mount this sensor on a parallel jaw gripper and demonstrate its utility on three distinct tasks: (i) pre-grasp adjustment, (ii) item extraction from clutter, and (iii) item insertion into tight spaces. For pre-grasp adjustment, ToF feedback reduced cycle time by 7.4%\% by enabling anticipatory gripper closure during approach. For extraction, ToF sensing enabled successful retrieval across all tested depth offsets (±\pm2 cm) deviating from the nominal pick point, including conditions where baseline approaches failed, with standard deviations below 0.4 cm. For insertion into dense clutter, we explore the proximity and tactile information provided from ToFTouch during an insertion trajectory. The results demonstrate the utility of multizone ToF sensing in a manipulation environment.

Figures & tables

Explore similar work

Sep 18, 2026

ZeroTouch: Tactile-Supervised Visual Contact Estimation for Contact-Rich Manipulation

Reliable robotic grasping benefits from estimating the evolving physical interaction and selecting a grasp-dependent compression target. Tactile sensors provide direct interaction measurements but require dedicated hardware at deployment. We introduce ZeroTouch, a tactile-supervised framework that predicts dense contact deformation, the instantaneous six-axis wrench, and a grasp-dependent desired compression target from wrist RGB observations, gripper state, and local gravity direction. Tactile measurements are used only as privileged supervision during training and are not required at deployment. On the full validation set, the complete architecture reduces normal-force MAE from 2.017 N for a state-only baseline to 0.531 N. In physical evaluation with 20 trials per condition, ZeroTouch achieves 95% success on an unseen object, 80% in a seen-object/unseen-grasp condition, and 90% under a content/load shift. Under the same evaluation protocol, OpenVLA achieves 25%, 40%, and 55%, while SmolVLA achieves 10%, 25%, and 35%, respectively.
Aug 7, 2026

Detection and Ranging of Transient Extrinsic Contacts Based on 6D Dynamic Tactile Sensing

Delicate manipulation often involves transient and subtle collisions between a grasped object and the environment. While the human hand localizes these contacts effortlessly thanks to superior tactile sensitivity, robotic systems often lack the requisite resolution to acquire the information necessary for motion planning, resulting in clumsy manipulation or even task failure. Here, we propose transient extrinsic contact detection and ranging (TECDAR), a simple yet fast and efficient method for detecting and ranging extrinsic contact of grasped objects. Our design of gripper tips employs dynamic tactile sensing leveraging a single 2.5×\times3 mm 6D inertial measurement unit. The sensor captures sub-millisecond tip deformations at a 7 kHz sampling rate, but operating on a data stream of only 84 KB/s. High bandwidth and compact data size enable the system to rapidly detect and localize contact between grasped objects and their surroundings. Specifically, fusing tactile data with robot pose via an extended Kalman filter enables fast and precise localization of extrinsic contact, reaching millimeter-level accuracy within 180 ms. Experimental results demonstrate that the system achieves an average localization accuracy of approximately 7,mm in both line-contact and point-contact localization tasks. Furthermore, this near-instantaneous localization enables the robot to rectify its trajectory on a millisecond scale, facilitating precise tool manipulation and enhanced perception of complex environments purely through tactile exploration and mapping. We envision such techniques advancing the future of robotics across domains requiring delicate manipulation, including precision assembly, surgical assistance, and autonomous exploration in touch-dominant environments. Project page: humitlab.github.io/TECDAR/
May 21, 2026

TacO: Benchmarking Tactile Sensors for Object Manipulation

Vision-based learning from demonstrations has achieved remarkable success in enabling robots to perform manipulation tasks and high-level semantic reasoning, yet it remains insufficient for complex, contact-rich manipulation. While there is broad agreement that tactile sensing improves manipulation, there is no empirical guidance on which tactile sensors are best suited for which manipulation tasks. In this paper, we provide a systematic, task-driven evaluation of tactile sensors for robot manipulation and propose a framework for selecting and evaluating sensors based on manipulation policy performance. Separate manipulation policies are trained for tactile sensors of four distinct modalities: visual, acoustic, magnetic, and resistive, across three tasks: pick-and-place with unknown mass, object reorientation, and plug insertion. For each task, we analyze how sensor properties, including spatial resolution, shear sensing, tactile representation, and inherent material friction, affect task performance. Rather than tactile sensing being universally beneficial in the same way, our results show that the usefulness of tactile information depends strongly on sensor modality, material properties, and the specific manipulation tasks. The tactile sensors, code, data, and hardware setup will be publicly available on the project website.