SunLightBots: Turning sunlight into self-sustained, high-power motion in soft robots
Authors: Yoo Jin Lee, Melanie Torres Crespo, Zhongxiao Deng, Andrew Tejada-Vega, Rebecca Kramer-Bottiglio, Wenzhong Yan, Yimin Luo
Organizations: Mechanical Engineering, Yale University, 9 Hillhouse Avenue, New Haven, 06511, CT, USA. · Mechanical and Aerospace Engineering, University of California, Davis, One Shields Avenue, Davis, 95616, CA, USA. · Present Address: Mechanical and Aerospace Engineering, Princeton University, Princeton, 08540, NJ, USA.
Soft robots built from active materials can directly convert environmental stimuli into motion, offering a route to energy autonomy and embodied control. However, environmental energy is generally harvested at low power, whereas rapid, mechanically demanding actions require high mechanical output power. Reconciling this mismatch while sustaining self-regulated cyclic actuation is challenging, particularly at the subgram scale, where limited payload capacity constrains the integration of conventional power and control hardware. Here, we present SunLightBots, a class of subgram, sunlight-powered, untethered soft robots that achieve autonomous locomotion under continuous illumination near 1 Sun (100 mW/cm2). Their operation is enabled by a self-resetting snapping (SRS) mechanism that integrates liquid crystal elastomers (LCEs) with snap-through instability to accumulate solar energy supplied at low power, release it as rapid, high-power motion, and reset through photothermal-mechanical feedback. Through coordinated optimization of the LCE actuation temperature, photothermal conversion, actuation stress, and structural energy barrier, the system operates near 1 Sun and achieves a peak mass-specific mechanical power of 89 W/kg. At this irradiance, the optimized LCE generates an actuation stress of 0.1 MPa at approximately 60 deg C. SunLightBots demonstrate sustained swimming, crawling, and repeated impulsive jumping. Under 1.5 Suns, the swimmer advances more than three body lengths per cycle. This work provides a materials-mechanics route toward autonomous soft robots powered entirely by the environment.
Figures & tables
Figure 1: Overview of the SunLightBots. ( a ) Photothermal actuation of liquid crystal elastomers (LCEs), with the light irradiance required for actuation reduced to 1 Sun illumination (100 mW cm -2 ). ( b ) Schematic force–displacement diagram of a monostable LCE–curved beam composite. As the (photo)thermally generated LCE force along the contraction direction reaches the snap-through threshold Fst , the beam snaps downward, abruptly releasing energy ΔE (shaded in green). As the force falls below the snap-back threshold Fsb , the beam returns to its upward configuration. ( c ) Coupling low-energy photothermal actuation of LCEs with a snap-through mechanism, the device enables reversible cycles of high-power mechanical output from a low-power solar input. ( d ) Ashby plot comparing the peak output specific power density of previously reported photothermally driven actuator systems. Our work is indicated by stars, each representing the optimized LCE formulation coupled to a different elastomer. The inset shows a magnified view of the data points near 1 Sun. ( e ) SRS-based SunLightBots can achieve various locomotion, including swimming, crawling, and jumping. The scale bars are 1 cm.
Figure 2: Optimization of the thermomechanical properties of LCEs. ( a ) Schematic of strategies used to develop LCEs that actuate under low energy input and produce high mechanical output. Methods 1, 3, and 5 vary the types and weight fractions of liquid-crystalline and non-liquid-crystalline acrylate monomers. Method 2 varies the crosslink density, and Method 4 varies the chain extender type. Details of the compositions are presented in Supplementary Table S2. ( b ) Comparison of energy input for actuation and mechanical output of LCEs developed using the applied strategies. Formulations A to E are either unmodified or taken from the literature, whereas Methods 1 to 5 describe the strategies used to modify them, as shown in Panel (a). The numerical sublabels then identify formulations obtained using each method. Energy input and mechanical output are evaluated by the temperature of onset of actuation and isometric stress at 100 °C, respectively. LCEs with the optimized formulation actuate around 60 °C and generate actuation stress of approximately 0.3 MPa. ( c ) Isometric stress as a function of temperature for the optimized formulation and controls C and D. ( d ) Actuation strain as a function of temperature for the optimized formulation and controls. Red \Circle ’s denote the optimized formulations, gold ◃ ’s denote Formulation D, and cyan ▹ ’s denote Formulation C, as indicated in Panel ( b ).
Figure 3: Optimization of the photothermal response of LCEs and LCE-based devices. ( a ) Schematic of photothermal actuation of a device comprising an LCE and a curved beam (top). With silver content fixed, the copper amount was varied to optimize photothermal efficiency. Device temperature throughout actuation was monitored using a thermal camera (bottom). ( b ) Representative images of light-driven actuation. LCE contraction under illumination deforms the curved beam and triggers snap-through. The scale bar is 5 mm. ( c ) Photothermal and ( d ) mechanical responses of LCEs with different copper contents under 1 and 2 Sun illumination. ( e ) Time-dependent changes in beam height and ( f ) temperature rise of the device under 1 Sun illumination. Colors and symbols denote LCE compositions with a fixed Ag loading amount of 1.5 wt% and different Cu loading: 0.75 wt% (red, circles), 1.5 wt% (blue, squares), 3 wt% (green, stars), and 6 wt% (gray, triangles).
Figure 4: Experimental setup and quantification of snap-through energy. (a) Schematic of the experimental setup shown in side and top views. (b) The released steel ball reaches a maximum height, hrise , allowing the released energy to be determined from the corresponding increase in potential energy against gravity. (c) Measurement of the contact time during snap-through. (d) Representative side-view montage of the snap-through process. Dragon Skin 30 served as the passive layer. The scale bar is 10 mm. (e) Released energy and peak power for samples with different silicone substrates. The estimated Young’s moduli are 0.12, 0.18, 0.36, and 0.52 MPa for Ecoflex 00-50 and Dragon Skin 10, 20, and 30, respectively, based on public data from Marechal et al. (2020) .
Figure 5: Sunlight-powered swimmer. ( a ) Schematic of the sunlight-driven swimming robot. The asymmetric paddle consists of a shorter stopper and a longer flapper with a flexible hinge. The asymmetric paddle design provides direction-dependent bending stiffness, converting snap-through and snap-back motions into directional propulsion underwater. ( b ) Simplified locomotion mechanism of the swimmer. Under illumination, the composite beam bends downward and drives the paddle through a recovery stroke, during which the flapper is soft and bends at the flexible hinge, substantially reducing the backward propulsive force. When the composite beam snaps back, the flapper is constrained by the stopper and behaves as a rigid paddle, generating a large propulsive force forward. The difference between the power and recovery strokes produces net directional locomotion. ( c ) Snapshots showing a swimming cycle under 1.5 Suns, including snap-through, snap-back, and the resulting net displacement. ( d ) Comparison of swimming speed and input light irradiance with previously reported light-powered swimmers and related locomotors.
Figure 6: Sunlight-powered crawler. ( a ) Schematic of the sunlight-powered crawling robot. ( b ) Simplified locomotion mechanism of the crawler over successive actuation cycles. The robot harnesses an asymmetric snap-back transition, during which the composite beam adopts an S-shaped configuration that drives rightward motion. The tilted leg provides direction-dependent friction, further promoting directional locomotion. ( c ) Under 1.5 Suns, self-sustained oscillation of the composite beam drives the crawler to move along the surface (Supplementary Movie S4). Scale bar: 15 mm. ( d ) Displacement of the crawler over time, showing stepwise locomotion driven by repeated oscillation cycles.
Figure 7: Sunlight-powered jumper. ( a ) Schematic of the sunlight-powered jumping robot. The robot incorporates shutters and balancers to enable repeated jumping. ( b ) Effect of passive-layer stiffness on robot motion. Actuation refers to snap-through without takeoff, which occurs under lower sunlight intensity or with softer elastomers. Compared with the softer DS10, DS20, and Ecoflex 00-50, the stiffer DS30 passive layer allows for greater elastic energy storage and release during snap-through, sufficient to drive jumping. The estimated Young’s moduli for Ecoflex 00-50 and Dragon Skin 10, 20, and 30 are 0.12, 0.18, 0.36, and 0.52 MPa respectively, based on public data from Marechal et al. (2020) . ( c ) Snapshots showing jumping under 2 Suns, driven by snap-through. The scale bar is 10 mm. ( d ) Jumping height over actuation cycles, showing reproducibility and no decrease in jumping height after more than 20 cycles.
We present the Swima, a bioinspired 900-mg swimmer propelled by two 10-mg high-work-density (HWD) actuators driven by shape-memory alloy (SMA) wires. We integrated onboard power and computation by using a custom-built printed circuit board (PCB) and an 11-mAh 3.7-V 507-mg single-cell lithium-ion (Li-Ion) battery, which in conjunction enable autonomous swimming in excess of 18 min. The Swima can swim at speeds of up to 22.4 mm/s (0.56 Bl/s), achieves turning rates of up to 14°/s, and can follow 0-degree heading reference trajectories with root mean square (RMS) values of tracking errors of about 6.5° across multiple tests. This robot is the first subgram microswimmer with onboard power, actuation, and computation developed to date.
Conor K. Trygstad, Francisco M. F. R. Gonçalves, Néstor O. Pérez-Arancibia
School of Mechanical and Materials Engineering, Washington State University (WSU), Pullman, WA 99164, USA
Soft and soft-rigid hybrid robots are inherently underactuated and operate under tight actuator limits, making task-space control with stability guarantees challenging. Common nonlinear strategies for soft robots (e.g., those based on PD control) often rely on the assumption of full actuation with no actuator limits. This paper presents a general control framework for task-space regulation and tracking of underactuated soft robots under bounded inputs. The method enforces a rapidly exponentially stabilizing control Lyapunov function as a convex inequality constraint while simultaneously satisfying underactuated full-body dynamics and actuator bounds. We validate the approach in simulation on several platforms spanning increasing underactuation: a simple two link tendon-driven "finger", a trimmed helicoid manipulator, and a highly underactuated spiral robot. We compare against a number of baseline methods from the literature. Results show improved task-space accuracy and consistent Lyapunov convergence under input limits, achieving superior set-point and trajectory-tracking performance.
Huy Pham, Zach J. Patterson
Mechanical and Aerospace Engineering, Case Western Reserve University
Snapping instabilities in soft structures offer a powerful pathway to achieve rapid and energy-efficient actuation. In this study, an eccentric dome-shaped snapping actuator is developed to generate controllable asymmetric motion through geometry-induced instability. Finite element simulations and experiments reveal consistent asymmetric deformation and the corresponding pressure characteristics. By coupling four snapping actuators in a pneumatic network, a compact quadrupedal robot achieves coordinated wavelike locomotion using only a single pressure input. The robot exhibits frequency-dependent performance with a maximum speed of 72.78mm/s at 7.5Hz. These findings demonstrate the potential of asymmetric snapping mechanisms for physically controlled actuation and lay the groundwork for fully untethered and efficient soft robotic systems.