Input-output characterization of robotic grasping: Connecting design parameters to grasp behavior through the admittance
Authors: Julien Vanderheyden, Guillaume Drion, Pierre Sacré, Fulvio Forni
Organizations: Department of Electrical Engineering and Computer Science, University of Li`ege, Belgium · Department of Engineering, University of Cambridge, United Kingdom
Low-impedance grippers make the dynamics of a grasp matter. Current grasp metrics, however, are static: they describe how a held object resists constant loads, not how it responds to time-varying ones. To quantify this, we rely on small-signal analysis to characterize a grasp by its admittance, the transfer matrix relating load perturbations to object displacements around an equilibrium. This transfer matrix recovers the stiffness and stability of the grasp at zero frequency and captures its natural frequencies and peak gain under time-varying loads. We apply this characterization to a planar two-finger gripper under proportional-derivative control. We show that two grasps of the same object in the same position and with the same contact forces can differ in stiffness by two orders of magnitude. Likewise, two grasps that share the same stiffness can exhibit very different resonances. Nonlinear simulations confirm the effectiveness of our small-signal analysis in capturing the dynamic behavior of grasping.
Figures & tables
Fig. 1: Planar gripper model: the palm and the two fingers push on the disk along their normals, with the forces f0n0 and fini , to balance the load F=(Fx,Fy) acting on the disk center c . Finger i rotates about pi , and its angle qi is measured from the x direction, positive when closing. It touches the disk at ai , at distance ℓi from its joint. A PD controller drives each finger toward the reference qref . The disk is drawn on the palm.
Symbol
Meaning
Value (nominal)
Gripper parameters: morphology
L
finger length
100mm
d
half-distance between the joints
40mm
If
finger inertia about its joint
6.7\times10−5kgm2
Gripper parameters: control
kp
proportional gain
1Nmrad−1
TABLE I: Parameters and variables.
Fig. 2: The finger angle in ( 4 ) follows from two right triangles that share the dotted hypotenuse from p1 to c (finger 1, disk off the axis). The tangency triangle ( blue ) has legs ℓ1 along t1 and r along n1 , with the right angle at the contact point a1 . The other triangle ( orange ) has legs cx and h1=d−cy . The finger angle is the angle of the hypotenuse, arctan(h1/cx) , minus ψ1=arctan(r/ℓ1) .
Fig. 3: The reference sets the shape of the holding force P(cx) : with qref=20\text{,}\mathrm{\SIUnitSymbolDegree} (left), $P$ rises then falls; with $q_{\mathrm{ref}}=$90\text{\,}\mathrm{\SIUnitSymbolDegree} (right), it decreases from the palm. Both use the same gain kp , but the holding force on the right is much larger. The equilibria lie where the horizontal line Fx meets the curve: stable (filled dots, solid) and unstable (empty dots, dashed) off the palm, and on the palm (square) while Fx≤P(r) .
Fig. 4: The reference qref and the normalized gain κ set the number, location (on or off the palm), and stability (S: stable, U: unstable) of the axial equilibria, for all loads and gains. Three curves separate the regions: palm-release (solid), fingertip (dotted), and fold (dashed).
Fig. 5: Along each black curve, the controllers (kp,qref) hold the disk at the same equilibrium. Moving up a curve raises kp , lowers qref toward the finger angle, and raises the stiffness. Left: curves of constant position, along which the disk rests off the palm at cx=355070\text{,}\mathrm{mm}$$ . The equilibrium is stable on the solid part and becomes unstable on the dashed part, the two parts meeting on the fold. Right: curves of constant holding force, P(r)=2Fx , 5Fx , and 20Fx .
Fig. 6: A larger disk moves the stable equilibria off the palm toward small references and large normalized gains. Bifurcation planes for r/d=0.5 , 0.75 , and 0.9 ; the regions are those of Fig. 4 , and the dots mark (q∗,κ∗) .
Fig. 7: Grasps at the same forced equilibrium differ in their dynamic response: a higher kp with a lower qref raises the stiffness and the natural frequency and sharpens the peak. Left: three grasps on the curve cx=35\text{,}\mathrm{mm}$$ of Fig. 5 (left), at (qref,κ)=(19.5\text{,}\mathrm{\SIUnitSymbolDegree},50) ( blue ), (17.0\text{,}\mathrm{\SIUnitSymbolDegree},100) ( rose ), and (14.7\text{,}\mathrm{\SIUnitSymbolDegree},1000) ( gray ). Right: axial (top) and lateral (bottom) admittances of these grasps. Dashed vertical lines mark the natural frequency ωn , and shaded bars the ratio supω∣Hxx(jω)∣/Hxx(0) .
Fig. 8: Grasps with the same stiffness differ in their peak gain, which grows as the disk moves away from the palm. Left: curves of constant stiffness Kxx=2080320\text{,}\mathrm{N}\text{,}{\mathrm{m}}^{-1} , for the load $F_{x}=$0.6\text{\,}\mathrm{N} . Grasps A, B, and C lie on the 20Nm−1 curve, at cx=60\text{,}\mathrm{mm}$$ (A, green ), 40mm (B, orange ), and 32mm (C, black ). Right: their axial admittance ∣Hxx∣ , with a linear zoom near ωn ; the DC gain Hxx(0) is the same.
Fig. 9: A larger finger inertia lowers the natural frequency, mostly in the lateral channel, where a peak appears. Axial (top) and lateral (bottom) admittances of grasp B of Fig. 8 , for the nominal finger inertia If=6.7\text{\times}{10}^{-5}\text{,}\mathrm{kg}\text{,}{\mathrm{m}}^{2}$$ and an inertia 10 times larger. The stiffness is the same.
Fig. 10: Nonlinear simulations of grasps A, B, and C of Fig. 8 . The failure amplitude of the nonlinear model is correlated with the axial admittance. Top: smallest amplitude of a sinusoidal axial load perturbation that ejects the disk (solid) or makes it land on the palm (dotted), normalized by the static margin (horizontal line). The vertical line marks the natural frequency ωn of the linearized model, shared by the three grasps. Bottom: response to an axial step of 0.85 times the static margin: A is ejected, B and C settle.
Underactuated robotic hands achieve adaptive and robust grasping with a reduced number of actuators, but predicting the stable equilibrium pose of the grasped object remains a significant challenge. This paper introduces a quasi-static analytical approach to assess passive stability in underactuated multi-finger hands. A novel three-finger hand architecture integrating a differential spring-loaded slider mechanism is introduced, enabling versatile and adaptive grasping. The study focuses on how the differential mechanism influences the overall grasp behavior and analyzes the effect of object size on the stable equilibrium configurations for two canonical grasp types: cylindrical and spherical.
Robots are increasingly used in unstructured environments. The need for them to safely grasp unknown objects without damaging them becomes crucial. Humans achieve this by sensing and quickly responding by adjusting their grasping force. Similarly, effective grasp acquisition in robots requires compliant interaction strategies that can adapt to uncertain object properties and adjust to any instabilities during manipulation. We present a geometry-aware force/torque-based contact estimation method for a coarse position-controlled gripper, combined with an adaptive admittance controller for safe grasp acquisition. The desired contact forces are estimated online to keep stable contact with objects of unknown properties. This enables compliant and stable grasps while avoiding excessive forces. Experiments with objects of different sizes, shapes, stiffnesses, and weights show that the proposed algorithm not only prevents slippage but also applies minimal force to safely grasp an object without causing excessive deformation.
Marko Pavlic, Moritz Geier, Timo Markert +1
Machine Vision and Perception Group, Chair of Robotics, Artificial Intelligence and Real-time Systems, Technical University of Munich, Munich, Germany · Resense GmbH, Klingenberg, Germany · Semantic Information Systems Group, Osnabrück University, Osnabrück, Germany
Dexterous robotic manipulation requires more than geometrically valid grasps: it demands physically grounded contact strategies that account for the spatially non-uniform mechanical properties of the object. However, existing grasp planners typically treat the surface as structurally homogeneous, even though contact in a weak region can damage the object despite a geometrically perfect grasp. We present a pipeline for grasp selection and force regulation in a five-fingered robotic hand, based on a map of locally admissible contact loads. From an operator command, the system identifies the target object, reconstructs its 3D geometry using SAM3D, and imports the model into Isaac Sim. A physics-informed geometric analysis then computes a force map that encodes the maximum lateral contact force admissible at each surface location without deformation. Grasp candidates are filtered by geometric validity and task-goal consistency. When multiple candidates are comparable under classical metrics, they are re-ranked using a force-map-aware criterion that favors grasps with contacts in mechanically admissible regions. An impedance controller scales the stiffness of each finger according to the locally admissible force at the contact point, enabling safe and reliable grasp execution. Validation on paper, plastic, and glass cups shows that the proposed approach consistently selects structurally stronger contact regions and keeps grip forces within safe bounds. In this way, the work reframes dexterous manipulation from a purely geometric problem into a physically grounded joint planning problem of grasp selection and grip execution for future humanoid systems.
Elizaveta Semenyakina, Ivan Snegirev, Mariya Lezina +3
Intelligent Space Robotics Laboratory, Skolkovo Institute of Science and Technology