Authors: Maximilian Mühlbauer, Nepomuk Werner, Ribin Balachandran, Thomas Hulin, João Silvério, Freek Stulp, Alin Albu-Schäffer
Abstract
Shared Control methods often use impedance control to track target poses in a robotic manipulator. The guidance behavior of such controllers is shaped by the used stiffness gains, which can be varying over time to achieve an adaptive guiding. When multiple target poses are tracked at the same time with varying importance, the corresponding output wrenches have to be arbitrated with weightings changing over time. In this work, we study the stabilization of both variable stiffness in impedance control as well as the arbitration of different controllers through a scaled addition of their output wrenches, reformulating both into a holistic framework. We identify passivity violations in the closed loop system and provide methods to passivate the system. The resulting approach can be used to stabilize standard impedance controllers, allowing for the development of novel and flexible shared control methods. We do not constrain the design of stiffness matrices or arbitration factors; both can be matrix-valued including off-diagonal elements and change arbitrarily over time. The proposed methods are furthermore validated in simulation as well as in real robot experiments on different systems, proving their effectiveness and showcasing different behaviors which can be utilized depending on the requirements of the shared control approach.
Contact-rich manipulation requires precise tracking and mechanical compliance, where variable impedance control can improve robustness in task success, whereas static compliance cannot adapt to varying contact constraints. Variable impedance skills can be learned from demonstrations, avoiding complex modeling, but compliance is a hidden variable in force-agnostic kinematic data. While existing methods infer compliance from trajectory variations, these variations may reflect geometric adaptation and not intentional compliance when subject to changing spatial layouts. Therefore, this letter introduces Variable Impedance Diffusion Policy (VIDP), an imitation learning-based variable impedance control framework leveraging a Task-Parameterized Directionality-Aware Mixture Model (TP-DAMM) to extract physically consistent trajectory distributions from diverse demonstrations. By mapping distributions to stiffness profiles, VIDP jointly predicts pose actions and task compliance without force sensors. Real-world experiments show that VIDP significantly outperforms fixed-impedance baselines in task success rate while reducing interaction forces with respect to high stiffness controllers and tracking errors with respect to low stiffness baselines.
Variable impedance model predictive control (MPC) formulations often treat joint stiffness as an instantaneous decision variable. The resulting feasible set strictly contains the physically realizable set under first-order actuator dynamics. We identify this as a formulation error rather than a modeling approximation, formalize the distinction between the parameter-based feasible set F_param and the realizable set F_real, and characterize the regime of mismatch via the dimensionless parameter α = ωsT (actuator bandwidth times task timescale). For the 1D hopping monoped, we prove that below an analytical threshold α_crit derived in closed form from task physics, no admissible stiffness command realizes the parameter-based prediction. Numerical validation in 1D shows monotonic deviation growth as α decreases, with the predicted scaling holding across ten parameter combinations (log-log R2 = 0.986). Mechanism transfer to planar spring-loaded inverted pendulum dynamics confirms center-of-mass and stance-timing deviation as the primary consequence, with regime-dependent friction effects as a tertiary observable. A second threshold α_infeas < α_crit establishes a floor below which restricting the admissible stiffness range cannot repair realizability, closing the conservative-tuning objection. Augmenting the prediction state with stiffness closes the mismatch by construction.
Safe physical interaction is critical for deploying robotic manipulators in human-robot interaction and contact-rich tasks, where uncertainty, external forces, and actuator limitations can compromise both performance and safety. We propose an online adaptive impedance control framework that enforces joint-state safety while achieving compliant interaction under uncertain dynamics. The approach combines a quadratic-program-based safety filter with a novel composed position-velocity non-smooth control barrier function (NCBF), enabling joint position and velocity constraints to be enforced through a unified relative-degree-one barrier. Unknown dynamics are compensated online using an interval type-2 fuzzy logic system, while actuator torque limits are handled through soft constraints with exact penalty recovery of feasible solutions. A disturbance-observer-enhanced safety mechanism improves robustness against modelling errors and external interaction forces. Using composite Lyapunov analysis, we prove forward invariance of the safe set and the uniform ultimately boundedness of the impedance-tracking error. Simulations on a 7-DOF manipulator with severe parametric uncertainty and external interaction wrenches demonstrate safe constraint satisfaction and robust impedance tracking.