Robot learning has advanced rapidly in learning control, but learning the physical body of a robot remains much more difficult because jointly searching over design and control creates a very large combinatorial problem. Here, we present a data-driven framework for generating robot hands from human demonstrations. Instead of learning a complex controller together with each candidate design, we generate robot hand designs using the same simple control policy used after fabrication: matching fingertip positions through inverse kinematics. Using more than 4 million frames of human fingertip motion from everyday manipulation, our algorithm optimizes tree-structured robot hands to reproduce desired target motions. The framework produced both a 6-degree-of-freedom (DoF) general-purpose hand and lower-DoF task-specific hands with spatial four-bar mimic joints. To accelerate the search over designs, we trained a reinforcement-learning (RL) actor to propose good hand designs and joint angles, reducing search time from hours to minutes. We fabricated the mechanisms directly as one-piece articulated structures with print-in-place joints. In real-world experiments, the 6-DoF hand achieved highly accurate teleoperated fingertip tracking better than available commercial robot hands, whereas the specialized 3-DoF hands reproduced structured human and synthetic trajectories with reduced mechanical complexity. These results showed that large-scale human motion data can be used not only to train robot controllers but also as a reference for optimizing and generating the physical embodiment of robots.
Human demonstrations offer a scalable way to collect manipulation data, but their contacts may be unstable or infeasible when transferred to a robot hand. Collecting demonstrations directly on the target robot avoids this mismatch but substantially increases the cost of data collection. To address this trade-off, we present Touch2Robot, a framework that lets humans collect demonstrations while seeing how the target robot hand would contact the object. We capture human hand motion, tactile-glove measurements, and object motion during human manipulation. These recordings guide object-specific RL policies to reproduce the demonstrated object motion while favoring contacts consistent with the recorded human touch. We distill the learned behaviors into a unified real-time retargeter that maps incoming human observations and object geometry to robot hand configurations. During collection, the predicted robot configuration is synchronized with the tracked object pose in simulation to reconstruct robot-object contacts, which are visualized to help the demonstrator adapt subsequent interactions to the target hand. Across four real-world tasks, Touch2Robot improves average real-robot replay completion from 37.9% to 72.1% over visual-only feedback, while reducing the collection time per replay-successful demonstration from 58.6s to 18.2s. Reconstructed target-hand contacts achieve 44.2% F1 against real-robot tactile measurements, and policies trained on Touch2Robot demonstrations improve downstream Diffusion Policy performance by 29.1 percentage points over visual-only feedback. These results show that bringing robot touch into the human demonstration loop improves both the quality and efficiency of scalable dexterous data collection. Project webpage: https://Touch2Robot.github.io/.
Dexterous manipulation is limited by both control and design, without consensus as to what makes manipulators best for performing dexterous tasks. This raises a fundamental challenge: how should we design and control robot manipulators that are optimized for dexterity? We present a co-design framework that learns task-specific hand morphology and complementary dexterous control policies. The framework supports 1) an expansive morphology search space including joint, finger, and palm generation, 2) scalable evaluation across the wide design space via morphology-conditioned cross-embodied control, and 3) real-world fabrication with accessible components. We evaluate the approach across multiple dexterous tasks, including in-hand rotation with simulation and real deployment. Our framework enables an end-to-end pipeline that can design, train, fabricate, and deploy a new robotic hand in under 24 hours. The full framework and generated robot hands are open-sourced and available on our website.
Learning dexterous manipulation from demonstrations is bottlenecked by data: the contact forces that determine whether a grasp succeeds are absent from every scalable source of human demonstrations. This paper builds on two observations. First, what survives the change from a human hand to a robot hand is the contact structure of a demonstration - which finger regions touch which object locations, and in what order - rather than its joint motion. Second, physical consistency need not be engineered per task: a single residual reinforcement learning (RL) policy, trained once across diverse demonstrations, can repair kinematic recordings into physically consistent, contact-annotated trajectories, and the same residual formulation restores dynamic feasibility after retargeting. These observations yield a three-stage pipeline that converts human motion-capture recordings into dexterous robot policies with no real-robot training data: physics refinement with a simulated MANO hand recovers contacts and forces, contact-anchored retargeting transfers the demonstrated contact structure through an objective independent of hand morphology, and residual policy learning adapts the result to robot actuation. The pipeline reconstructs 25,454 single-hand trajectories (success 7.3% -> 59.3%) and 25 dual-hand tasks (16.0% -> 62.4%) with one shared policy per setting, transfers one human dataset to four morphologically distinct robot hands (+62.4 pp), and executes four contact-rich bimanual tasks on physical hardware with zero real-robot training data.