Rebar insertion is among the most repetitive and physically demanding tasks on construction sites, and a contact-rich problem at 1.4 mm clearance. The parts, however, vary at two levels: a nominal design per structural member, and fabrication tolerance around each nominal design. Real-world data therefore has to be re-collected as designs and batches change. We present RebarSim, a visual sim-to-real system trained entirely in simulation. A privileged state-based teacher is trained with reinforcement learning over procedurally generated rebar geometries, then distilled into a multi-view student that maps raw RGB and proprioception directly to actions under extensive domain randomization. The student transfers to the real world zero-shot, seating rebars taken from a real factory production run in 91.3% of real-robot rollouts. Underlying that result, geometry diversity and pretraining both bring benefits. Training across a diverse set of nominal designs rather than one lifts the zero-shot success of both the teacher and the student on unseen designs, and the student policy outperforms a single-design specialist on that specialist's own design. A pretrained student then adapts to a new design with 4--6x fewer distillation samples than one trained from scratch. Visual sim-to-real transfer depends on appearance randomization and the DAgger mixture: removing either one sharply lowers success. Videos, code, and task assets are available at https://rebarsim.github.io.
Contact-rich precision insertion is a key manipulation skill in robotic assembly. Tight clearances make insertion more sensitive to alignment errors and prone to collisions and jamming, while variations in geometry and clearance across parts further complicate policy reuse. We present a reinforcement learning framework that trains insertion policies entirely in simulation for direct deployment without real-world demonstrations or policy fine-tuning. By combining target poses with compact three-dimensional fingertip force feedback, the policy learns to search for alignment and correct its motion despite errors in the estimated hole position. A decoupled gated reward coordinates alignment and insertion. Force-signal smoothing and state-independent standard deviations stabilize the learning process. The resulting policies perform real-world insertion across multiple hole geometries with a minimum nominal clearance of 0.02 mm and improve success while reducing peak contact forces under hole-position errors. Cross-clearance and cross-geometry evaluations further confirm policy generalization. The system achieved the first perfect score of 20/20 on ManipulationNet's peg-in-hole benchmark under its Human-in-the-Loop protocol, with fully autonomous insertion motions. A single policy trained only on a simulated hexagonal insertion task achieved an overall success rate of 95.0% across eight unseen real-world insertion tasks. These results show that learning entirely in simulation can yield precision insertion skills that can be deployed directly and reused across real-world tasks. The project website (https://mzhsoul.github.io/InsertAnything/) provides open-source simulation and real-robot experiment scripts, assets, and trained checkpoints.
RGB sim-to-real for deformable manipulation has remained largely unsolved without real-world fine-tuning. We present SimWeaver, which trains zero-shot RGB VLA policies on 200 simulated demonstrations per task, reaching above 80% per-task and 91% average real-world success across 5 diverse deformable tasks including plastic-bag manipulation, without teleoperation or per-task calibration. SimWeaver combines a reliable measurement-backed simulator (SimWeaver-Sim) with an extensible asset framework supporting single-image generation(SimWeaver-Asset), a deterministic topology-aware trajectory synthesizer (SimWeaver-Syn), and a sim-to-real protocol with ISP-aware photometric augmentation (SimWeaver-Real). On silk grasping, the sim-trained policy reaches 100% under visual distribution shifts where real-data baselines drop to 9-70%, at two orders of magnitude lower per-trajectory cost. We will release SimWeaver and a representative asset subset. Project page: https://simweaver.github.io/
In recent years, reinforcement learning (RL) has shown remarkable success in robotics when a fast and accurate simulator is available for a given task. When using RL and simulation, more simulator realism is generally beneficial but becomes harder to obtain as robots are deployed in increasingly complex and widescale domains. In such settings, simulators will likely fail to model all relevant details of a given target task and this observation motivates the study of sim2real with simulators that leave out key task details. In this paper, we formalize and study the abstract sim2real problem: given an abstract simulator that models a target task at a coarse level of abstraction, how can we train a policy with RL in the abstract simulator and successfully transfer it to the real-world? Our first contribution is to formalize this problem using the language of state abstraction from the RL literature. This framing shows that an abstract simulator can be grounded to match the target task if the grounded abstract dynamics take the history of states into account. Based on the formalism, we then introduce a method that uses real-world task data to correct the dynamics of the abstract simulator. We then show that this method enables successful policy transfer both in sim2sim and sim2real evaluation.