eess.SYNov 8, 2026

Concurrent Learning-Based Inertial Parameter Estimation and Control of Quadrotors

Authors: Sandesh Thapa, He Bai

Organizations: ETAIC Lab, University of Texas at Arlington, Arlington, TX 76019, USA · School of Mechanical & Aerospace Engineering, Oklahoma State University, Stillwater, OK 74078, USA

Abstract

In this letter, we consider trajectory tracking control and inertial parameter estimation of a quadrotor UAV whose center of mass (CoM) does not coincide with its geometric center. Onboard payloads like an IMU, a camera, or a battery are not necessarily placed at its geometric center. Moreover, during the flight these sensors might move because of external disturbances and cause a CoM offset. Thus, these events and equipment introduce an offset and cause the inertia matrix to be non-diagonal. We develop an integral concurrent learning (ICL)-based geometric controller that estimates the mass, the CoM offset, and the full inertia matrix online, without an accelerometer or numerical derivatives, and tracks a given trajectory corrected by the offset estimated online. We prove that the estimated parameters converge to their true values under a finite excitation condition. We validate the effectiveness of the proposed algorithm using a simulation example.

Figures & tables

Explore similar work

May 6, 2026

Robust H∞\mathcal{H}_\infty Controller Design For INDI-Controlled Quadrotor Using Online Parameter Identification

It has recently been shown that all physical parameters of an Incremental Nonlinear Dynamic Inversion (INDI) controller can be estimated onboard a multirotor within half a second, which is fast enough to do the full identification during a throw in the air. However, a robust method to tune outer loop gains for this feedback-linearizing INDI controller depending on the model parameters is still missing. This work presents the design of a robust gain-scheduled controller for attitude control of quadrotor, using an INDI-based inner loop with online identification of its system parameters. A gain-scheduled cascaded attitude controller with a feedforward filter is synthesized for a symmetric quadrotor using signal-based H∞\mathcal{H}_\infty closed-loop shaping. The resulting controller exhibits good stability margins, with nonlinear simulations confirming effective tracking performance under uncertainty. Experimental evaluation is also conducted through flight tests with full online parameter identification. Even though the identified parameters during these tests are far outside the defined uncertainty range, acceptable flight performance comparable to simulation results is maintained for actuator time constants below 40 ms.
Nov 6, 2026

Extended Model-Based Learned Inertial Odometry

Inertial odometry is a compelling approach to state estimation for agile quadrotor flight due to its affordability, low weight, and robustness to perceptual degradation. However, relying only on integrated inertial measurements is impractical, as sensor errors and time-varying biases lead to significant pose drift. Although recent advances have enabled inertial odometry for drone racing, existing approaches show limited generalization to trajectories not seen during training. This work improves generalization by adopting a body-frame representation and incorporating body-frame torque dynamics into the learning pipeline. The learned model predicts short-horizon relative displacements, which are fused with IMU measurements in an Extended Kalman Filter. Experimental results show that the proposed method outperforms the previous state-of-the-art learned inertial odometry approach for quadrotor pose estimation on unseen trajectories. An additional evaluation on four public quadrotor datasets, with whole trajectory shapes held out of training, confirms a lower velocity error on every held-out set and shows that the torque input is most informative when it is derived from the rotor signals. Code, data pipeline and trained models are publicly available.
Feb 28, 2026

AI-IO: An Aerodynamics-Inspired Real-Time Inertial Odometry for Quadrotors

Inertial Odometry (IO) has gained attention in quadrotor applications due to its sole reliance on inertial measurement units (IMUs), attributed to its lightweight design, low cost, and robust performance across diverse environments. However, most existing learning-based inertial odometry systems for quadrotors either use only IMU data or include additional dynamics-related inputs such as thrust, but still lack a principled formulation of the underlying physical model to be learned. This lack of interpretability hampers the model's ability to generalize and often limits its accuracy. In this work, we approach the inertial odometry learning problem from a different perspective. Inspired by the aerodynamics model and IMU measurement model, we identify the key physical quantity--rotor speed measurements required for inertial odometry and design a transformer-based inertial odometry. By incorporating rotor speed measurements, the proposed model improves velocity prediction accuracy by 36.9%. Furthermore, the transformer architecture more effectively exploits temporal dependencies for denoising and aerodynamics modeling, yielding an additional 22.4% accuracy gain over previous results. To support evaluation, we also provide a real-world quadrotor flight dataset capturing IMU measurements and rotor speed for high-speed motion. Finally, combined with an uncertainty-aware extended Kalman filter (EKF), our framework is validated across multiple datasets and real-time systems, demonstrating superior accuracy, generalization, and real-time performance. We share the code and data to promote further research (https://github.com/SJTU-ViSYS-team/AI-IO).