Self-Supervised Attention-Based Virtual Metrology for CMP MRR Prediction
Authors: Jonathan Adam Rico, Nagarajan Raghavan, Senthilnath Jayavelu
Organizations: Engineering Product Development, SUTD, Singapore · Institute of Advanced Intelligence and Computing, A*STAR, Singapore · Dept. of Electrical and Computer Engineering, NUS, Singapore
Chemical mechanical planarization (CMP) is a critical semiconductor manufacturing process where material removal rate (MRR) is a key metric for process monitoring and advanced process control (APC). Virtual metrology enables MRR estimation from process time series signals, supporting run-to-run(R2R) control and process optimization while reducing reliance on physical metrology. Existing approaches typically rely on simplified linear assumptions or require handcrafted feature engineering. In this paper, we propose Global Regression Pretraining(GREP), a self-supervised, attention-based framework for CMP MRR prediction. GREP learns temporal representations from unlabeled sensor signals through global proxy-target regression, followed by supervised fine-tuning for MRR estimation. The framework is evaluated against a feature-engineered supervised baseline under three conditions: limited labeled data, sensor noise, and temporal process drift. Experiments on the PHM 2016 CMP dataset demonstrate competitive performance under limited labeled-data conditions, with improvements in selected cases and performance largely comparable to the baseline across different labeled-data fractions. Both models exhibit relatively small changes in prediction error with increasing noise, while GREP achieves a 17.0% RMSE reduction in the final temporal interval.
Figures & tables
Fig. 1: Overview of the proposed self-supervised GREP architecture for MRR virtual metrology.
Mode
Chamber
Average MRR
Train
Test
Low-speed
4,5,6
55-110 nm/min
1613
364
High-speed
1,2,3
140-170 nm/min
351
73
TABLE I: Details on the number of train and test samples for each of the operating modes of a CMP run.
Fig. 2: MRR Prediction RMSE under different training-signal noise levels and varying proportions of labeled training data.
Fig. 3: MRR prediction RMSE across four temporal partitions, with training restricted to the first partition.
Virtual metrology (VM) aims to estimate costly or delayed metrology variables from heterogeneous sensor signals and in-line measurements, and it acts as a critical component of semiconductor manufacturing. While recent data-driven models have improved VM accuracy, most are trained in batch settings and assume stationary data distributions. In practice, however, production environments evolve continuously due to equipment degradation, process adjustments, and maintenance events, making conventional batch-trained VM models difficult to maintain under temporal distribution shifts. In this work, we propose GRAPE (Global Regression with Adaptive Prediction Enhancement), a practical online learning framework for VM in evolving wafer-processing environments. GRAPE integrates a stable global predictor based on interpretable representations with two lightweight streaming adapters that correct feature-level and environment-level shifts through online updates. Experiments on two real-world semiconductor manufacturing datasets, including chronologically held-out blind-test streams, show that GRAPE improves robustness and generalization under real temporal drift compared with both conventional batch-learning methods and existing online learning baselines.
Doyun Choi, Cheonwoo Lee, Younghyun Han +5
Seoul National University, Seoul, Republic of Korea · KAIST, Daejeon, Republic of Korea · Samsung Electronics, Hwaseong, Republic of Korea
As time-to-market is crucial in the Integrated Circuit (IC) industry, speeding up layout manufacturability verifi-cation is essential. Chemical-Mechanical Polishing (CMP) plays a vital role in IC fabrication but is significantly influenced by Layout-Dependent Effects (LDE). An accurate and efficient CMP model enables design teams to correct surface unevenness before fabrication, reducing costs and accelerating the design phase. However, existing models often rely on Density Step Height (DSH) modeling, which is time-consuming for calibration and requires substantial hardware resources for fine-grained predictions. In this paper, we propose combining the advantages of two surface analysis techniques, White Light Interfer-ometry (WLI) and Atomic Force Microscopy (AFM), to train a deep learning model. This model aims to predict full-chip post-CMP nanotopography with nanometer-scale accuracy. Our deep learning model is based on a Convolutional Neural Network (CNN) and follows a two-step pipeline. The model is trained on each technique separately, resulting in a detailed full-chip CMP model.
Jules Exbrayat, Renan Bouis, Elie Sezestre +4
Univ. Grenoble Alpes, CEA, Leti, F-38000 Grenoble, France
High-level Computer-Aided Process Planning (CAPP) generates manufacturing process plans from part specifications. It suffers from limited dataset availability in industry, reducing model generalization. We propose a semi-supervised learning approach to improve transformer-based CAPP transformer models without manual labeling. An oracle, trained on available transformer behaviour data, filters correct predictions from unseen parts, which are then used for one-shot retraining. Experiments on small-scale datasets with simulated ground truth across the full data distribution show consistent accuracy gains over baselines, demonstrating the method's effectiveness in data-scarce manufacturing environments.
Dennis Gross, Helge Spieker, Arnaud Gotlieb +3
1- Simula Research Laboratory, Oslo Norway · 2- National Technical University of Athens, School of Mechanical Engineering, Manufacturing Technology Laboratory Greece