Hierarchical Admittance-Impedance Control for Mobile Manipulator Load Transfer
Authors: Minghao Xu, Thushara Sandakalum, Christina Dao Wen Lee, Marcelo H. Ang
Organizations: NUS Graduate School, National University of Singapore, Singapore 119077 · Department of Mechanical Engineering, National University of Singapore, Singapore 119077
This paper presents a hierarchical admittance-impedance controller that combines an inner Cartesian impedance controller, an outer 6D admittance supervisor, and workspace-aware mobile-base assistance for guided load transfer. The method is motivated by assistive tasks such as airport baggage handling, where a robot should support a payload while a human worker guides its motion through small physical forces. Following an interaction-role interpretation of admittance and impedance, the torque-controlled Franka Research 3 manipulator behaves as a Cartesian impedance at the robot-object interface, providing compliant load support around a commanded equilibrium pose. At the human-facing interaction level, the outer admittance supervisor converts measured human wrench input into smooth Cartesian reference motion. The workspace-aware assistance layer shares the admittance-generated translational motion between the manipulator and a velocity-controlled base when larger motion is required, while front-side load alignment keeps the carried object near the robot's frontal region for safer and more intuitive guidance. The system was implemented in ROS and validated through a suitcase transfer experiment, showing that the robot can support the load while allowing the human to guide the transfer with relatively little effort.
Figures & tables
Figure 1: Physical roles during human-guided load transfer using a mobile manipulator.
Figure 2: Hierarchical admittance-impedance control architecture for human-guided load transfer with workspace-aware mobile-base assistance.
Figure 3: Supervisory logic for robot-assisted load transfer
Figure 4: Experimental Setup
Figure 5: Recorded data from the robot-assisted suitcase transfer experiment.
Indicator
Average
Minimum
Maximum
Human guidance force (N)
7.43
0.00
20.22
Total end-effector force (N)
29.49
15.11
40.31
Manipulator extension (m)
0.612
0.570
0.645
Absolute load angle (deg)
10.31
0.01
19.54
Table 1: Quantitative results during Stage 3 human-guided loaded transfer from 24s to 52s .
Articulated object manipulation tasks such as opening doors, tightening bolts, and pulling drawers impose kinematic constraints on a robot end-effector's motion that neural policies may fail to satisfy. Unlike hybrid force-position control that strictly separates force and position control into orthogonal subspaces, impedance control modulates a mechanical impedance system in the form of a virtual inertia, damping, and stiffness. However, selecting task-appropriate impedance gains remains challenging for robot policies. In this paper, we address this problem for the case of manipulating articulated objects. Our constraint-decomposed impedance control method uses the sampling diversity of a generative policy to estimate the feasible motion directions in twist space. The key idea is to infer the feasible and constrained subspaces of twists from an ensemble of trajectories generated by the policy from the same observation. Principal component analysis (PCA) of the end-effector twists determines the feasible twist subspace, which is then used to form 6x6 impedance gain matrices. For many common articulated objects, the feasible twist subspace is independent of the object configuration, so the subspace and resulting gains are estimated once and held fixed during manipulation, minimizing computational overhead. For less common cases where this independence does not hold, we instead estimate a configuration-independent twist subspace of higher dimension that contains the local feasible subspaces, allowing the same fixed-gain strategy to be used. Experiments across simulated and real-world single- and multi-DoF objects show that the proposed method consistently reduces constraint-violating contact loads relative to isotropic impedance control while maintaining task execution.
Kyungseo Park, Byeongdo Lim, Jungbin Lim +2
Seoul National University · Department of Mechanical Engineering, KAIST
Unknown payloads can strongly affect compliant robotic manipulation, especially when the payload center of mass is not aligned with the tool center point. In this case, the payload generates an offset wrench at the robot wrist. During motion, this wrench is not only related to payload weight, but also to payload inertia. If it is not modeled, the compliant controller can interpret it as an external interaction wrench, which causes unintended compliant motion, larger tracking error, and reduced transport accuracy. This paper presents a wrench-aware admittance control framework for unknown-payload pick-and-place using a UR5e robot. The method uses force-torque measurements in two different roles. First, a three-axis translational excitation term is used to reduce payload-induced force effects during transport without making the robot excessively stiff. Second, after grasping, the controller first estimates payload mass for transport compensation and then estimates the payload CoM offset relative to the TCP using wrist force-torque measurements collected during the subsequent translational motion. This helps improve object placement and stacking behavior. Experimental results show improved transport and placement performance compared with uncorrected placement while preserving compliant motion.
Hossein Gholampour, Logan E. Beaver
Department of Mechanical & Aerospace Engineering, Old Dominion University, Norfolk, VA 23529, USA
With advancements in learning-based policies, robots are increasingly being deployed in human-centric environments, such as manufacturing floors and homes, where safe and precise operation requires compensating for unknown loads while remaining compliant during human interactions. Reliably distinguishing between these interaction types is challenging with a single sensing modality, as force signals cannot separate payloads from human pushes, and vision is susceptible to occlusions. We propose a task-agnostic interaction estimation and adaptive control framework that addresses this challenge by fusing force history and 3D point cloud through a transformer-based classifier. Trained with modality dropout for occlusion resilience and fine-tuned from simulation to hardware, the classifier achieves 91.89% accuracy and maintains above 90% under complete occlusion of one modality. The classifier drives a system identification framework that selectively compensates for unknown payloads and a variable-impedance controller that switches between adaptive and reactive modes, while simultaneously estimating interaction forces for downstream tasks, such as human intent estimation. We validate the framework under external perturbations and unknown loads across single-arm manipulation, deployment with an imitation-learning-based policy, intent-driven target switching, and zero-shot bimanual deployment on two Franka arms lifting a box of unknown mass, demonstrating generalization to closed kinematic chains and unseen setups, enabling safe and precise deployment.
Mateusz Jaszczuk, Paris Perdikaris, Nadia Figueroa
Department of Mechanical Engineering, University of Pennsylvania