Time-Division Multiplexing Actuation in Tendon-Driven Arms: Lightweight Design and Fault Tolerance

High-DOF dexterous hands require compact actuation, rich sensing, and reliable thermal behavior, but conventional designs often occupy valuable in-hand space, increase end-effector mass, and suffer from heat accumulation near the hand. Remote tendon-driven actuation offers an alternative by relocating motors to the robot base or an external motor hub, thereby freeing the fingers and palm for additional degrees of freedom, sensing modules, and maintainable mechanical structures. This paper presents MM-Hand, a 21-DOF Multimodal Modular dexterous hand based on remote tendon-driven actuation. The hand integrates spring-return tendon-driven fingers, modular 3D-printed finger and palm structures, quick tendon connectors for maintenance, and a multimodal sensing system including joint angle sensors, tactile sensors, motor-side feedback, and in-palm stereo vision. We further analyze tendon-sheath length variation and friction loss to guide the design of the routing, motor hub, and closed-loop joint control. Experiments validate the transmission, output force, sensing, and control capability of the system. The fingertip force reaches 25N under a 1m remote sheath transmission, demonstrating practical load capacity despite long-distance tendon routing. Closed-loop joint-level experiments further evaluate command tracking with a static arm and during arm motion. These results show that MM-Hand provides a lightweight, sensor-rich, and maintainable hardware platform for dexterous manipulation research. To support the community, all hardware designs and software frameworks are made fully open-source at https://mmlab.hk/research/MM-Hand.

Aerial physical interaction requires aerial manipulation platforms to generate large interaction forces and torques while maintaining precise end-effector control. However, conventional underactuated aerial manipulators suffer from strong position-attitude coupling, whereas fully actuated platform designs often face structural complexity, limited payload capacity, and insufficient torque output. This paper presents FAM-DQ, a dual-quadrotor based fully actuated aerial manipulator designed for high-torque physical interaction tasks. By mounting two quadrotor propulsion modules at the ends of a central frame through passive joints, while using a gear-driven servo to regulate the pointing direction, FAM-DQ achieves decoupled $6$-DoF end-effector control with omnidirectional manipulation capability and enhanced torque output. Experiments including trajectory tracking, attitude tracking, static torque measurement, and screw driving validate the proposed design. FAM-DQ achieves a maximum torque of $1.019~\mathrm{N}\cdot\mathrm{m}$ with a total mass of $0.447~\mathrm{kg}$, corresponding to a torque-to-mass ratio of $2.28~\mathrm{N}\cdot\mathrm{m/kg}$.

This paper presents the design, modeling, and fabrication of 3D-printed, tendon-actuated continuum robots featuring a flexible, tapered backbone constructed from thermoplastic polyurethane (TPU). Our scalable design incorporates an integrated electronics base housing that enables direct tendon tension control and sensing via actuators and compression load cells. Unlike many continuum robots that are single-purpose and costly, the proposed design prioritizes customizability, rapid assembly, and low cost while enabling high curvature and enhanced distal compliance through geometric tapering, thereby supporting a broad range of compliant robotic inspection and manipulation tasks. We develop a generalized forward kinetostatic model of the tapered backbone based on Cosserat rod theory using a Newtonian approach, extending existing tendon-actuated Cosserat rod formulations to explicitly account for spatially varying backbone cross-sectional geometry. The model captures the graded stiffness profile induced by the tapering and enables systematic exploration of the configuration space as a function of the geometric design parameters. Specifically, we analyze how the backbone taper angle influences the robot's configuration space and manipulability. The model is validated against motion capture data, achieving centimeter-level shape prediction accuracy after calibrating Young's modulus via a line search that minimizes modeling error. We further demonstrate teleoperated grasping using an endoscopic gripper routed along the continuum robot, mounted on a 6-DoF robotic arm. Parameterized iLogic/CAD scripts are provided for rapid geometry generation and scaling. The presented framework establishes a simple, rapid, and reproducible pathway from parametric design to controlled tendon actuation for tapered, tendon-driven continuum robots manufactured using fused deposition modeling 3D printers.