Organizations: IRiS Lab, Department of Civil and Environmental Engineering, Korea Advanced Institute of Science and Technology, Daejeon, Korea. · CHARM Lab, Department of Mechanical Engineering, Stanford University, Stanford, CA, USA.
Abstract
Conventional soft robot actuators excel in compliance, but their uncontrolled deformations compromise accuracy and hinder scaling to multi-degree-of-freedom (DoF) systems. We introduce a MONOlithic ORIGAMI-inspired soft folding actuator design (MONORIGAMI) that establishes a design strategy based on spatially programmed stiffness anisotropy to preserve material compliance along desired folding directions while selectively restricting deformation in unwanted directions. The actuator leverages stiffness tiers based on material thickness, patterned in an origami-inspired geometry with facets and creases, converting unconstrained soft deformation into accurate, repeatable, and composable folding motions without additional reinforcements. The design is fully 3D-printable through a single-material, single-print process that requires no assembly. Each actuator serves as a scalable motion primitive, and linking and orienting multiple actuators mechanically programs multi-DoF trajectories. Using the same fundamental module, we demonstrate three 3D-printed soft multi-DoF robotic systems spanning distinct application domains: (1) a compact 4-DoF wearable haptic device for high-fidelity cutaneous feedback in virtual reality (VR), (2) a 3-DoF joystick for kinesthetic feedback in teleoperation, and (3) a modular robotic gripper capable of underwater operation with geometry-encoded grasp trajectories. These systems demonstrate the module's capabilities for compact multi-axis integration, controlled physical interaction, and geometry-programmed operation across different environments. Together, these results show that MONORIGAMI provides a general, composable, accessible, reliable, and scalable platform for high-precision soft multi-DoF robotics, addressing long-standing limitations in both soft actuator design and fabrication.
The passive adaptability inherent in soft robotic hands affords them advantages in applications that require safe and compliant interaction. However, existing soft robotic hands often struggle to simultaneously achieve adequate output performance and easy manufacturing due to their complicated structures. In this paper, we introduce the asymmetric origami bending (AOB) pattern for generating bending motion and the asymmetric dual-chamber (ADC) design for obtaining multifunction capability. The AOB single (AOB-S) chamber and AOB dual-chamber (AOB-D) units are designed and constitute the finger and palm actuators of the proposed Origami-inspired SOft Robotic (OSOR) hand. The OSOR hand achieves bio-inspired fingers-palm motions and adequate output performance within a monolithic structure that significantly simplifies the manufacturing process. By defining the asymmetric ratio to characterize the geometric asymmetry of the unit, the analytical models of the AOB and ADC structures are proposed. The Finite Element Analysis tool for the design of AOB actuators is obtained by geometric analysis. The asymmetric origami design grants the integrated manufacturing of the OSOR hand through a Selective Laser Sintering printing process with a single thermoplastic polyurethane material. The model and simulations are validated by experimental results. Experiments show the finger and palm maximum bending motion range of 203° and 40°, respectively, with output forces of 6.3 N and 16 N. The OSOR hand is capable of pinching a piece of tissue, stably grasping water bottles with two fingers, palm-only grasping, and completing the power grasps in the taxonomy of manufacturing grasps. The compactness, performance, and easy manufacturing of the proposed hand benefit the development of the soft robotic hand with new possibilities.
Functional magnetic composites capable of large deformation, load bearing, and multifunctional motion are essential for next-generation adaptive soft robots. Here, we present muscle-inspired magnetic actuators (MMA), additively manufactured from a thermoplastic/permanent magnet polyurethane/Nd2Fe14B (TPU/MQP-S) composite using laser powder bed fusion (LPBF). By tuning the laser-energy scale between 1.0 and 3.0, both mechanical stiffness and magnetic response are precisely controlled: the tensile strength increases from 0.28 to 0.99 MPa while maintaining 30-45% elongation at break. This process enables the creation of 0.5 mm-thick flexural hinges, which reversibly bend and fold under moderate magnetic fields without damage. Two actuator types are reported showing the system versatility. The elongated actuator with self-weight of 1.57 g, magnetized in its contracted state, achieves linear contraction under a 500 mT field, lifting 50 g (32x its own weight) and sustaining performance over at least 50 cycles. Equipped with anisotropic frictional feet, it supports movement of a magnetic crawling robot that achieves up to 100% locomotion success on textured substrates. The expandable actuator exhibits reversible opening and closing under a 300 mT field, reliably grasping and releasing different objects, including soft berries and rigid 3D printed geometries. It can also anchor in a tube while holding suspended 50 g loads. This work demonstrates a LPBF-based strategy to program both stiffness and magnetization within a single material system, enabling remotely driven, reconfigurable, and fatigue-resistant soft actuators. The approach opens new possibilities for force controlled, multifunctional magnetic soft robots for adaptive gripping, locomotion, and minimally invasive manipulation of biomedical tools.
Muhammad Bilal Khan, Florian Hofmann, Kilian Schäfer +2
Soft lattice structures are increasingly used in robotics to tailor compliance and guide deformation; however, actuation is typically introduced at the device or module level, with actuators inserted into otherwise passive architectures. In this work, we move actuator-lattice co-design to the unit-cell scale. We present an embedded pneumatic unit cell that integrates curved-strut lattice geometry with a bidirectional bellow actuator within a single monolithic element. When tessellated, the lattice functions as a distributed actuation field in which global morphology is governed by spatial actuation patterns rather than uniform pressurization. Experimental characterization of 1x1, 2x2, and 3x3 tessellations demonstrates scalable displacement and force generation with repeatable cyclic performance. Selective actuation of unit cells in a 3x3x3 array produces distinct global deformation modes, including bending and directional grasping, without altering hardware configuration. Additionally, coupling active and passive unit cells enables bending-driven crawling locomotion, demonstrating that heterogeneous tessellations can translate through asymmetric deformation. These results establish unit-cell-level actuation as a strategy for distributed morphing in lattice-based soft robots and provide a foundation for scalable, monolithic robotic architectures.