LUMO: Designing Luminous Contact Morphology for Repeatable Whole-Finger Contact Observation

Human-centric data collection is emerging as a significant paradigm for robot skill acquisition, but seamlessly integrating low-cost, scalable tactile sensing systems that capture fine-grained fingertip interactions without compromising natural operation remains a key challenge. This reduces the reliability of human-to-robot transfer in contact-rich tasks. In this work, we present TacPrint, a wearable fingertip tactile sensor, where protrusions on the inner surface of the silicone skin are aligned one-to-one with 24 capacitive taxels to enable localized capacitive responses. A real-to-sim-to-real pipeline estimates a 35 $\times$ 26 contact-depth map from 24-channel capacitive signals. Against simulation-generated labels, the model achieved a contact-region RMSE of 0.223 $\pm$ 0.161 mm, a weighted-centroid error of 1.213 $\pm$ 2.379 pixels, and an IoU of 0.829 $\pm$ 0.169. With measured capacitive inputs, the network-predicted depth evaluated at the guide-calibrated contact center showed a mean absolute error of 0.085 $\pm$ 0.057 mm across all 40 controlled trials, while the mean contact-position error was 0.250 $\pm$ 0.208 mm across the 37 trials whose reference contact regions were not truncated by the sensing boundary. In human-to-robot replay, tactile-guided compensation increased grasping and wiping success rates from 0% to 91.67% and 90%, respectively. In closed-loop grasping, dense-depth feedback achieved success rates of 87.5% over all tested positions and 85% under edge-contact conditions, compared with 67.5% and 45% for raw-taxel feedback.

Accurate tactile forecasts need not improve force-constrained control. We study a 652,157-parameter action-conditioned visuotactile world model with matched behavior cloning, policy learning in imagination, independent reactive implicit Q-learning, and model-assisted force feedback. A fixed protocol executes 34 policies on 120 fresh MuJoCo environments spanning geometry and physical-parameter shifts, plus 324 independently replayed action branches on 12 additional ID environments. Visuotactile dynamics reduce force action-effect MAE from 0.413 N for persistence to 0.338 N. Model-assisted feedback raises ID force-budgeted success from 73.3% to 93.3%, with paired difference +20.0 [+6.7,+33.4] percentage points (95% CI), with the difference occurring during scripted lowering. Its pooled difference is +3.9 [-4.5,+11.7] points. Imagined RL achieves 11.9% pooled joint success versus 25.0% for reactive IQL. An empirical tactile-residual stress test adds 330 executions. The evidence concerns rigid-box lifting after a common approach, without physical-robot transfer or a closed-loop safety guarantee.

Grasp force estimation can help prevent robots from damaging delicate objects during manipulation and improve learning-based robotic control. Integrating force sensing into deformable grippers negotiates trade-offs in cost, complexity, mechanical robustness, and performance. With the growing integration of RGB-D wrist cameras into robotic systems for control purposes, camera-based techniques are a promising solution for indirect visual force estimation. Current approaches mostly utilize end-to-end deep learning, which can be brittle when generalizing to new scenarios, while existing model-based approaches are unsuited to grasping and modern grasper geometries. To address these challenges, we developed a model-based visual force sensing approach integrating an iterative contact localization with generalization to unseen objects. The system extracts structural key points from wrist camera RGB-D images of deforming fin-ray-shaped soft grippers, and uses these key points to define parameters of an inverse finite element analysis simulation in Simulation Open Framework Architecture. The iterative contact localization sub-system utilizes a deep learning-based online 3D reconstruction and pose estimation pipeline to dynamically update contact location, and is robust to visual occlusion and unseen objects. Our system demonstrated an average root mean square error of 0.23 N and normalized root mean square deviation of 2.11% during the load phase, and 0.48 N and 4.34% over the entire grasping process when interacting with different objects under various conditions, showcasing its potential for real-time model-based indirect force sensing of soft grippers.