High-Speed Forward and Reverse Tractor-Trailer Driving with Learned Vehicle Dynamics
Authors: Aaron Chen, David Shen, Taekyung Kim, Kaleb Ben Naveed, Dimitra Panagou
Organizations: Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor, MI, 48109, USA · Department of Robotics, University of Michigan, Ann Arbor, MI, 48109, USA · Department of Aerospace Engineering, University of Michigan, Ann Arbor, MI, 48109, USA
Tractor-trailer systems are difficult to control, especially unstable during reverse motion, and their dynamics depend on difficult-to-measure factors, including road friction and suspension coefficients. We introduce a learned dynamics model for tractor-trailer control and compare it with a reduced-order dynamics model with Fiala tire forces as an analytic baseline. Specifically, we compare a model predictive path integral (MPPI) controller that uses the learned dynamics model to an MPPI controller that uses the analytic model, as well as to three additional baseline controllers. In the main closed-loop tracking experiments across four simulated environments, MPPI with learned dynamics achieves mean speeds closer to the target magnitudes and lower root-mean-square (RMS) hitch angles than MPPI with the analytic model at every tested setpoint, with higher completion rates in seven of eight reverse configurations.
Figures & tables
Fig. 1: Illustration of our tractor-trailer model. The tractor is approximated by a bicycle model and the trailer by a single axle connected to the tractor at a common hitch point.
Fig. 2: Overview of our controller architecture. MPPI uses a multilayer perceptron (MLP) trained offline to predict dynamic-state and actuator rates from a sliding window of state-action pairs. These predictions are integrated recursively to generate candidate trajectories for receding-horizon control.
Fig. 3: Top-down view of the Snow + Slope test environment, based on the Circuit de Barcelona-Catalunya layout. Snow patches and terrain changes are applied to the base asphalt track. The snow pattern matches the Snow environment, and the terrain profile matches the Slope environment.
Fig. 4: Representative reverse-driving trajectories of Controller 1 in (a) Asphalt, (b) Snow, (c) Slope, and (d) Snow + Slope. White patches indicate snow-covered regions with lower friction.
Parameter
Forward
Reverse
kv
1×102
5×101
kc
1×100
5×101
ka
7×102
1×102
λ (temperature)
150
100
diag(Σ)
(7×10−2,0.2)
(2×10−2,0.2)
K (samples)
500
500
TABLE I: MPPI settings for the main tracking experiments. Sampling covariance is expressed in normalized command coordinates (uδ,ua) .
Asphalt
Snow
Slope
Snow + Slope
Controller
v⋆
vˉ
αˉrms
Nˉ
C/J/S/O/F
vˉ
αˉrms
Nˉ
C/J/S/O/F
vˉ
αˉrms
Nˉ
C/J/S/O/F
vˉ
αˉrms
Nˉ
C/J/S/O/F
(km/h)
(km/h)
(deg)
(steps)
(out of 9)
(km/h)
(deg)
(steps)
(out of 9)
(km/h)
(deg)
(steps)
(out of 9)
(km/h)
(deg)
(steps)
(out of 9)
1: Ours
−30
29.1
1.14
500
9/0/0/0/0
29.1
1.18
500
9/0/0/0/0
25.4
1.03
455
8/0/1/0/0
20.4
10.82
386
6/0/3/0/0
−50
47.2
1.75
500
9/0/0/0/0
46.0
1.82
500
9/0/0/0/0
42.1
3.06
498
8/1/0/0/0
30.4
15.41
413
4/0/5/0/0
80
75.4
2.57
500
9/0/0/0/0
72.6
2.72
500
9/0/0/0/0
70.7
2.67
500
9/0/0/0/0
69.1
2.83
500
9/0/0/0/0
2: MPPI (analytic) [ 7 ]
−30
19.7
5.25
392
5/0/4/0/0
19.6
7.82
403
5/0/4/0/0
22.3
2.86
498
8/0/1/0/0
16.7
11.47
365
4/0/5/0/0
TABLE II: Closed-loop tracking across four environments, with nine runs per configuration. Controllers are defined in Section IV-A . Bold hitch-angle values are the lowest for each velocity setpoint and environment.
Fig. 5: Five-second open-loop dynamics predictions in Snow + Slope for forward (a,b,c) and reverse (d,e,f) driving. The measured trajectory is shown in dotted black, and the dynamics models’ open-loop predictions are shown in solid color. Terminal tractor and trailer poses are denoted by solid and hollow boxes, respectively. The blue shading denotes snow patches with decreased friction, and elevation contours are spaced at 5 m.
Analytic
Friction-aware analytic
Learned
Direction
Environment
ep
eα
ep
eα
ep
eα
Reverse
Asphalt
5.8
96.5
7.4
113.0
4.2
101.1
Snow
7.0
130.1
4.9
107.9
4.0
88.2
Slope
7.7
132.6
8.2
134.2
2.2
78.7
Snow + Slope
8.1
131.5
7.3
111.6
2.1
83.4
Forward
Asphalt
7.3
93.4
6.6
95.3
1.4
2.1
TABLE III: Position ( ep ) and wrapped hitch-angle ( eα ) RMSE for one five-second segment per direction and environment (meters and degrees, respectively). Bold values indicate the lowest RMSE for each environment, direction, and metric.
Predictor
v⋆
vˉ
αˉrms
Nˉ
C/J/S/O/F
(km/h)
(km/h)
(deg)
(steps)
(out of 3)
H=1
−30
15.8
29.29
98
0/3/0/0/0
80
48.0
22.27
278
0/2/0/1/0
H=4
−30
30.0
2.84
500
3/0/0/0/0
80
51.6
29.29
345
0/3/0/0/0
H=8
−30
30.9
2.87
500
3/0/0/0/0
TABLE IV: Closed-loop history comparison on Snow + Slope.
Fully autonomous tractor-trailer systems are increasingly deployed in logistics, agriculture, and industrial environments, where precise and robust path-tracking capabilities are essential. However, the articulation between the tractor and the trailer introduces additional nonlinearities and significantly complicates lateral and longitudinal control, particularly during reversing maneuvers. This paper introduces a novel path-tracking algorithm specifically designed for articulated vehicles with a single trailer. The proposed method combines a lateral control law applied at the trailer level with a short-horizon predictive adjustment of the tractor steering angle, ensuring stable convergence toward the desired path in both forward and backward motion. The approach is geometry-based and requires no per-vehicle calibration or training. Simulation studies in a high-fidelity physics simulator show steady-state or final lateral errors of 0.02--0.05m on straight-line, circular, and reverse docking trajectories, which is of the same order of magnitude as, or lower than, the errors reported in the literature. Real-world experiments on a small-scale tractor--trailer robot, with the whole controller running on a low-cost microcontroller, further confirm the feasibility of the approach, with lateral errors below 13mm during repeated reverse docking maneuvers despite a pose detection latency of about 200~ms.
This paper presents a novel non-linear mathematical model of an articulated tractor-trailer system that can be used, in combination with receding horizon techniques, to improve the performance of path tracking tasks of articulated systems. Due to its dual steering mechanisms, this type of vehicle can be very useful in precision agriculture, particularly for seeding, spraying and harvesting in small fields. The articulated tractor-trailer system model was embedded within a non-linear model predictive controller and the trailer position was monitored. When the kinematic of the trailer was considered, the deviation of trailer's position was reduced substantially alongside not only straight paths but also in headland turns. Using the proposed mathematical model, we were able to control the trailer's position itself rather than the tractor's position. The Robot Operating System (ROS) framework and Gazebo simulator were used to perform realistic simulations examples.
Marina Murillo, Guido Sanchez, Nestor Deniz +2
Research Institute for Signals, Systems and Computational Intelligence, sinc(i), FICH-UNL/CONICET, Ciudad Universitaria UNL, 4◦piso FICH, (S3000) Santa Fe, Argentina.
This paper presents a trajectory planning method for articulated commercial vehicles, specifically tractor-semitrailers, based on Model Predictive Contouring Control (MPCC). Although MPCC has proven effective for passenger cars, it is generally ill-suited for tractor-semitrailers. These vehicles are significantly larger, the semitrailer follows a different path than the tractor, and reversing maneuvers are unstable and prone to jackknifing. Furthermore, practical driving scenarios often require scenario-dependent prioritization of different vehicle `anchor points', e.g., prioritizing the semitrailer position during docking or the tractor position when parking to charge. Therefore, we extend MPCC to enable scenario-dependent weighting of these anchor points and incorporate explicit road-boundary constraints for the front and rear tractor axles and the semitrailer axle, thereby ensuring that all considered wheels remain within the drivable area. The simulation results demonstrate the successful navigation of a representative logistic scenario in both forward and reverse direction. Furthermore, the influence of the optimization parameters on the trajectories is analyzed, providing insights into controlling the vehicle behavior. Finally, first tests using a full-scale prototype vehicle show the practical applicability of the approach.
A. J. Aertssen, R. G. M. Huisman, I. J. M. Besselink +2
Department of Mechanical Engineering, Eindhoven University of Technology, Eindhoven, The Netherlands. · Safety & Driver Controls Group, Vehicle Development, DAF Trucks N.V., Eindhoven, The Netherlands.