ALS boresight calibration has relied for two decades on dedicated flight patterns over structured scenes containing planar surfaces of varied aspect and slope. While reliable, this approach imposes constraints on the scene content and operations, which limits its applicability to boresight recovery within routine mapping missions. We present a practical approach that substantially relaxes these requirements by replacing plane-based constraints with scene-agnostic point-to-point correspondences extracted automatically from overlapping ALS strips. Two complementary formulations are proposed to estimate boresight with laser vector observations: (i) a simpler parametric adjustment utilizing INS/GNSS trajectory; (ii) a rigorous formulation treating GNSS and raw inertial data within an existing factor-graph, i.e. a dynamic network, where boresight is added as an additional parameter. Both formulations are evaluated across four operational ALS flights equipped with five inertial systems, covering a wide range of flight altitudes, overlap geometries, terrain types and inertial sensor classes. The analysis draws a clear boundary between the legacy plane-based conditioning that falls short outside the calibration scenario and the proposed formulations, which either recover or absorb boresight effects under conventional mapping geometry. Among them, the lightweight formulation is sufficient for boresight recovery using tactical and navigation grade inertial sensors, while the general factor-graph approach is clearly superior when the inertial sensor errors are less observable within an optimal smoother. This supports the hypothesis that, for INS/GNSS trajectory of sufficient quality, the boresight calibration can be performed without particular scene prerequisites during routine mapping operations using a minimum of 3-4 overlapping strips, with either proposed formulation...
Triaxial MEMS accelerometers are widely used for inertial sensing, navigation, and sensor fusion, but existing calibration methods often rely on costly reference setups or nonlinear iterative optimization, limiting their efficiency and applicability to low-cost or self-calibrating systems. We present attitude-aided linear accelerometer calibration (ALAC), a method that operates on any platform providing orientation information, such as turntables, robotic arms, or inertial measurement units. ALAC constructs a combined error matrix (CEM) to represent sensor errors in a unified calibration model and enables linear least-squares estimation. The bias and gravity vector are jointly estimated, implicitly accounting for platform misalignment, and matrix decomposition of the CEM recovers scale, non-orthogonality, and alignment rotation parameters. Under static gravity, calibration is formulated as a constrained homogeneous least-squares (CHLS) problem and solved in closed form using standard linear algebra. Only five arbitrarily oriented measurements are required, and a recursive extension supports online or in-field calibration. Experiments on a stationary robot-mounted accelerometer and a quasi-static public IMU trajectory show that ALAC, in both offline and online modes, outperforms reference-based and online baselines in accuracy and robustness to sensor noise. On the same dataset, it matches iterative self-calibration under filtered conditions and surpasses all evaluated baselines on raw measurements. These results demonstrate a robust and practical calibration scheme for MEMS-based inertial platforms, especially low-cost IMUs and online calibration scenarios.
Target-based LiDAR-camera extrinsic calibration is a prerequisite for multi-sensor fusion in robotics. However, in the widely adopted four-hole pipeline, calibration accuracy is bottlenecked by LiDAR-side hole-center extraction, which suffers from sparse angular coverage and mixed-pixel corruption. This paper presents P2Calib, which exploits pattern priors, geometric constraints specified by the CAD model of the target board, to improve calibration accuracy. First, we incorporate the known hole radius as a fitting constraint to prevent center estimates from degrading under sparse angular coverage. Building on the improved hole estimates, we further enforce the rigid rectangular layout of the four holes as a global consistency constraint to correct residual errors across holes. Both priors are integrated into an interactive calibration tool that provides a complete extrinsic calibration pipeline. Experiments on simulated and real datasets show that P2Calib lowers the joint registration residual by 90% and 82% and the held-out reprojection error by 96% and 77% over the baseline. Code, https://github.com/JokerJohn/P2Calib.git, and data will be released to facilitate future research.
We present CalibBEV, a novel Bird's Eye View (BEV) alignment approach for LiDAR-camera calibration. Our method unifies LiDAR and camera data into a shared 3D spatial representation, enabling accurate and robust cross-modal calibration. CalibBEV extracts sensor-wise BEV features from each modality using domain-specific architectures and estimates the calibration matrix through a two-step alignment process. First, we perform an implicit alignment by regressing a coarse calibration matrix directly from the BEV features. To ease this alignment, we enforce semantic consistency between BEV representations across modalities using a contrastive loss inspired by CLIP, guiding both networks toward a unified feature space. In the second step, we leverage our BEV formulation to explicitly align the features of one modality with the other, refining the initial coarse estimate into a final, more accurate calibration matrix. CalibBEV significantly outperforms prior point-to-pixel matching methods, achieving state-of-the-art calibration accuracy. On the KITTI and nuScenes benchmarks, our method reduces the Relative Rotation Error (RRE) by 51% and 68%, and the Relative Translation Error (RTE) by 80% and 91%, respectively, compared to previous methods.
Filippo D'Addeo, Lorenzo Cipelli, Adriano Cardace +3