Organizations: Faculty of Innovation Engineering, Macau University of Science and Technology, Macau, China · School of Aeronautical Science and Engineering, Beihang University, Beijing, China · Institute of Unmanned System, Beihang University, Beijing, China
A rudderless dual vectored-thrust flying wing combines vertical takeoff and landing with efficient for- ward flight in a compact tailless configuration. Without aerodynamic control surfaces, vectored thrust couples translation and pitch control. Therefore, generating dy- namically compatible trajectories remains an open chal- lenge. To address this challenge, this study proposes a trajectory generation method that jointly optimizes path geometry and timing. Trajectory inversion yields state and control histories that satisfy the coupled equations of motion. The optimization balances curvature-induced acceleration against aerodynamic support, lowering thrust- vectoring demand while retaining the defining maneuver features. Representative looping and rolling sequences are tracked in closed-loop simulations. These results provide a basis for planning autonomous aerobatic maneuvers with rudderless vectored-thrust aircraft.
Figures & tables
Fig. 1: Aircraft configuration, body axes and dual vectored-thrust actuation.
Fig. 2: S-shaped climb before and after joint geometry and timing optimization. The endpoint motion and duration are fixed.
Fig. 3: Cloverleaf with four quarter rolls (F1). Dashed curves show the original geometry, and solid curves show the closed-loop path. Enlarged aircraft use actual attitudes and applied vectoring commands at equal arc-length intervals. Numbers indicate flight order.
Fig. 4: Reverse half-Cuban and half-Cuban sequence (F4), using the same conventions as Fig. 3 .
Fig. 5: Straight rolling sequence (F8): continuous roll, four-point roll and knife-edge hold.
Case
nmax
Ωmax
ep,max (mm)
γR,max (deg)
F1
1.34
0.72
1.3
0.041
F4
2.94
0.70
6.7
0.77
F8
1.01
0.58
4.0
0.90
TABLE I: Closed-loop response of the illustrated sequences.
Fig. 6: F1 closed-loop response. In (a,b), solid curves are actual states and dashed curves are references. Quaternion components (w,x,y,z) use blue, orange, yellow and purple; body rates (x,y,z) use blue, orange and yellow. Applied input channels 1 and 2 use blue and orange.
Fig. 7: F4 closed-loop response. In (a,b), solid curves are actual states and dashed curves are references. Quaternion components (w,x,y,z) use blue, orange, yellow and purple; body rates (x,y,z) use blue, orange and yellow. Applied input channels 1 and 2 use blue and orange.
Fig. 8: F8 closed-loop response. In (a,b), solid curves are actual states and dashed curves are references. Quaternion components (w,x,y,z) use blue, orange, yellow and purple; body rates (x,y,z) use blue, orange and yellow. Applied input channels 1 and 2 use blue and orange.
Trajectory optimization computes motion or control sequences that minimize costs while satisfying system dynamics, safety limits, and task constraints.
Bidirectional thrust grants quadrotors a second equilibrium condition and increased control authority, expanding the envelope of possible aggressive maneuvers and enabling inverted flight, perching, and sensing. Prior geometric control approaches extend differential flatness through Hopf fibration-based attitude representations to support bidirectional thrust, but struggle with actuator saturation and motor reversal delay during inversions, requiring heuristic thrust posture scheduling and waypoint tuning. We propose a learning-based framework that modulates a constant reference trajectory to perform compact, position-constrained quadrotor inversions while remaining compatible with traditional trajectory generation and tracking across flight regimes. Separate policies are trained via reinforcement learning for nominal-to-inverted and inverted-to-nominal transitions. In JAX-based simulation, the proposed method achieves the lowest position deviation and settling time across all evaluated baselines, reducing position root mean square error (RMSE) by 32% and settling time by 57% relative to the strongest optimization-based baseline. Hardware experiments demonstrate successful inversion across multiple yaw configurations with position RMSE below 0.35m, and compatibility with downstream trajectory generation and control through circular flight in both regimes. Additionally, we provide an open-source implementation of the proposed framework.
Gabriel Rodriguez, Henri Sayag, Abhishek Rathod +4
We present a robotics-oriented, coordinate-free formulation of inverse flight dynamics for fixed-wing aircraft on SO(3). Translational force balance is written in the world frame and rotational dynamics in the body frame; aerodynamic directions (drag, lift, side) are defined geometrically, avoiding local attitude coordinates. Enforcing coordinated flight (no sideslip), we derive a closed-form trajectory-to-input map yielding the attitude, angular velocity, and thrust-angle-of-attack pair, and we recover the aerodynamic moment coefficients component-wise. Applying such a map to tethered flight on spherical parallels, we obtain analytic expressions for the required bank angle and identify a specific zero-bank locus where the tether tension exactly balances centrifugal effects, highlighting the decoupling between aerodynamic coordination and the apparent gravity vector. Under a simple lift/drag law, the minimal-thrust angle of attack admits a closed form. These pointwise quasi-steady inversion solutions become steady-flight trim when the trajectory and rotational dynamics are time-invariant. The framework bridges inverse simulation in aeronautics with geometric modeling in robotics, providing a rigorous building block for trajectory design and feasibility checks.
Antonio Franchi, Chiara Gabellieri
Robotics and Mechatronics lab, Faculty of Electrical Engineering, Mathematics & Computer Science, University of Twente, Enschede, The Netherlands. · Department of Computer, Control and Management Engineering, Sapienza University of Rome, 00185 Rome, Italy.
This paper presents QuadRocket, a quadrotor-based rocket prototype that provides a low-cost, low-risk platform for validating advanced thrust-vector control strategies for launch vehicle-type systems. The prototype consists of a cylindrical main body mounted on top of a quadrotor through a universal joint, forming a flying inverted pendulum with non-negligible inertia. For control design, the coupled system is modeled as a single axisymmetric rigid body actuated by a vectored force applied along its longitudinal axis. A reduced-attitude representation on the two sphere is adopted to explicitly exploit the vehicle's axial symmetry and to decouple yaw from the thrust-vector direction. On this model, we derive an adaptive backstepping controller that achieves almost global trajectory tracking in the presence of unknown constant disturbances, while a control-point transformation mitigates non minimum-phase behavior. The quadrotor is then treated as a thrust vector actuator, and a dynamic-surface-based attitude controller is designed to track the desired thrust-vector, accounting for actuation dynamics and avoiding explicit differentiation of virtual control signals. The complete architecture is evaluated in simulation and validated experimentally in an indoor motion-capture arena. Results demonstrate accurate trajectory tracking, effective disturbance compensation, and confirm the suitability of the QuadRocket as a versatile testbed for thrust-vector-controlled robotic vehicles.
Pedro Santos, Joel Reis, Paulo Oliveira +1
Instituto Superior T´ecnico, Universidade de Lisboa, Lisbon, Portugal · Faculty of Science and Technology, University of Macau, Taipa, Macao, China