Robot Dynamics Identification

Simulation-to-reality transfer, often called sim-to-real transfer, is a central challenge in robot learning. Yet, the tradeoff between measuring a system more accurately and training over a broader range of simulated dynamics is still poorly understood. In this work, we focused on the allocation of real-robot measurement time between system identification and domain randomization. We studied this tradeoff in a controlled sim-to-sim pendulum setting, where a hidden-parameter model stands in for the physical robot, and the experiment sweeps identification rollouts against the width of the randomization distribution. Across the reality gaps and noise levels we tested, the measurement budget did most of the work. A small number of identification rollouts closed most of the transfer gap, and once any real data was available, policies performed best when trained at the estimated parameters rather than over a widened randomization band. Broad randomization that contained the true system still did not substitute for measurement. These results hold in a benign regime where the dynamics are identifiable and only two parameters are unknown, so structural model mismatch remains the setting where randomization breadth may become more valuable. Overall, our results suggest that sim-to-real pipelines should first measure the parameters they can and reserve randomization for the uncertainty that remains.

Aerial manipulators enable physical interaction in hard-to-reach environments; however, the combined problem of direct whole-body aerial manipulation under rapid arm motion, payload changes, and related unknown dynamic uncertainty remains a largely unsolved problem. We present a hierarchical control framework that combines Reinforcement Learning (RL) with an inner-loop dynamics estimator to address this problem. The RL outer loop maps desired 6-degrees-of-freedom (DOF) end-effector targets to coordinated whole-body commands, enabling direct task-driven control without relying on a fully accurate coupled dynamic model in the policy layer. An inner loop then tracks these commands while compensating for transient inertial shifts and uncertainty during execution via a dynamics estimator scheme without requiring system model knowledge. We validate the proposed approach on a custom quadrotor equipped with a 3-DoF manipulator through hardware experiments under varying payload conditions. Compared with RL+PID and RL+INDI+PID baselines, the proposed method reduces end-effector tracking error and improves task success rate across the tested hardware conditions. These results show that combining learned whole-body coordination with estimator-based low-level compensation improves the precision and robustness of aerial manipulation under changing operating conditions.

Robotic systems deployed in uncertain and dynamically changing environments often face variations in contact conditions, aerodynamic effects, and external disturbances that challenge reliable control. To remain effective under model-based control, these systems require dynamics models that can adapt to such changes, especially when direct access to complete environmental information is limited. To enable adaptability and facilitate integration with model predictive control, we propose a context-aware dynamics model based on neural ordinary differential equations, which infers environmental factors from state-action histories using a two-phase training procedure. We validate the approach across diverse robotic platforms, including a quadrotor in simulation, as well as a Sphero BOLT robot and a Fanuc manipulator in real-world experiments. The results demonstrate that our method effectively adapts to temporally and spatially varying environmental changes across different tasks. Videos are available at https://youtu.be/PY0sNyF2rqE , and the source code is available at https://github.com/syyu410-yu/context-aware-neural-ode-control.git .

Accurate dynamics models are essential for model-based robotic control, yet nominal Euler--Lagrange models often become inaccurate in the presence of payload variation, unmodeled coupling, friction, aerodynamic effects, and changing operating conditions. Most learning-based correction methods improve prediction accuracy by introducing a single additive residual, but do not preserve the internal mechanical structure of Euler--Lagrange systems. This leads to models that do not preserve symmetry, positive-definiteness, or the coupling between inertia and velocity-dependent terms, which can result in physically inconsistent predictions and reduced reliability when embedded in model-based controllers. We propose a structure-preserving residual learning framework that decomposes model mismatch into an inertia correction, the corresponding induced Coriolis term, and a generalized-force residual. The mechanical component is learned under physical constraints, while the disturbance-sensitive component is represented through a sparse history-dependent latent interaction model and adapted online using Bayesian linear regression. This separation preserves key mechanical structure while restricting adaptation to the part of the dynamics most affected by changing conditions. Experiments across multiple robotic platforms, including mobile, aerial, and manipulator systems, show that the proposed method improves dynamics prediction and trajectory tracking under coupled and time-varying dynamics. These results highlight the value of combining structured residual modeling, compact latent interaction selection, and selective online adaptation for real-world model-based control.

This paper examines three approaches for modeling the dynamics of a flexible-link 2-DoF robotic arm to address unmodeled dynamics not captured by rigid-body models. Two physics informed models combine rigid-body dynamics (RBD) formulations with a Gaussian Mixture Model (GMM) to capture residual model errors and linkage flexibility. A kinematics-based regression model serves as a purely data-driven baseline. Using an open-source dataset, torque predictions are first estimated using Ridge regression on kinematic features, while the physicsbased baseline is constructed from published specifications, and ordinary least-squares regression is subsequently used to estimate the same parameter set directly from data. Results show that the physics-based parameters yield the poorest accuracy, while regularized and least-squares estimators align more closely with measured torques. Residual analysis and error metrics highlight the limitations of purely parametric models for flexible-link systems and underscore the value of regularization and data-driven identification, supporting developments of semi-parametric residual learning methods.

We present a kinematic and transmission-aware design framework for a serial spherical mechanism with an additional translational degree of freedom for microsurgery. The first contribution is an analytical workspace formulation that provides geometric insight into reachable motion and enables rapid selection of rotation axis orientations without numerical optimization. The second contribution is a dynamics-informed methodology for mechanisms driven by self-locking transmissions, supporting evaluation of torque requirements for a prescribed workspace geometry. The framework is accompanied by an open-source software package for friction identification and inverse dynamics analysis. Experiments on a purpose-built robotic tool for vitreoretinal surgery validate the predictive capability of the models and demonstrate their practical utility for engineering design.

Developing dynamic models for tendon-driven continuum robots is challenging due to their nonlinear, high-dimensional, and friction-dominated dynamics. This paper presents a comparative study of data-driven system identification methods, including N4SID, ARX, and SINDYc, for modeling a tendon-actuated continuum robot with rolling joints developed at CERN. Despite the high number of joints of the robot, experimental analysis reveals that a two-degree-of-freedom dynamic model can accurately capture the system dynamics, owing to strong kinematic dependencies between the joints. The models are validated against experimental data, and used in the design of a model predictive controller, demonstrating their feasibility for real-time control.

Humanoid and legged robots interact with the environment through intermittent contacts, making accurate motion estimation fundamentally dependent on reasoning about contact dynamics. However, standard sensing pipelines-whether based on onboard proprioception with Extended Kalman Filters (EKFs) or external motion capture systems-recover only kinematics, while contact forces, contact timing, and inertial parameters remain unobserved. As a result, purely kinematic reconstructions often violate rigid-body dynamics, particularly during contact-rich motions. To enable accurate motion estimation from onboard kinematics in real-world deployment, we propose PRIME (Physically-consistent Robotic Inertial and Motion Estimation), a Maximum A Posteriori (MAP) formulation that refines measured kinematics and actuator commands into a dynamically consistent trajectory while jointly estimating frictional contact forces and physically consistent inertial parameters. Our approach incorporates differentiable contact dynamics with smoothed complementarity constraints and an Anitescu-style friction model, yielding a smooth optimization problem that remains tractable across versatile contact transitions. We evaluate PRIME on contact-rich locomotion with quadrupedal robots and the Unitree G1 humanoid, demonstrating improved trajectory consistency and accurate inertial parameter identification. Beyond improving state estimation and feedback control with calibrated inertial parameters, PRIME produces force- and contact-annotated motion reconstructions from real robots in deployment, which can be used to provide high-quality data for downstream learning applications, including large-scale behavior modeling and robot foundation models.

This paper presents a reproducible and physically feasible dynamic parameter identification framework for CRANE-X7, a low-cost robot arm driven by modular smart actuators. To improve practical identifiability, products of inertia are removed according to approximate link symmetry, reducing the rigid-body model from 65 to 39 base parameters. Identification motions are hand-designed from structured single-joint and adjacent-joint primitives under practical joint-range limits. The proposed pipeline combines preprocessing, inverse-dynamics-regressor-based ordinary least squares (OLS), conditional semidefinite-programming (SDP) projection for feasibility recovery, and closed-loop input error (CLIE) refinement. Candidate solutions from 40 structured trajectories are analyzed in a common principal component analysis (PCA) space to select a statistically central representative model. Because statistical centrality alone does not ensure physical acceptability, the selected model is finally screened by an all-pose positive-definiteness audit of the inertia matrix and, when necessary, corrected by a localized post-CLIE SDP rescue step. Experiments show that the parameter cloud becomes progressively more concentrated from OLS to SDP and CLIE, while the final accepted model preserves high predictive accuracy on held-out validation motions. These results demonstrate a practical route to statistically coherent and physically feasible dynamic models for low-cost robot platforms.

Many robotic tasks are unforgiving; a single mistake in a dynamic throw can lead to unacceptable delays or unrecoverable failure. We introduce Wiggle and Go!, a two-stage framework for zero-shot rope manipulation: a brief, safe wiggle action is observed to predict descriptive rope parameters, which then conditions a trajectory optimizer for zero-shot goal-conditioned execution. Unlike prior dynamic rope manipulation methods that require large real-world datasets or iterative real-world refinement, our identification module is task-agnostic, supporting diverse manipulation policies without retraining. We achieve a 3.55,cm average accuracy on 3D target striking in real using rope system parameters in comparison to 15.29,cm for uninformed baselines, and over 50% success on multi-objective lobbing and draping tasks. Predicted parameters transfer to unseen motions with 0.95 Pearson correlation between simulated and real rope dynamics, indicating that the identification module generalizes across the task corpus. Project website: https://wiggleandgo.github.io/

Accurate modeling of robot dynamics is essential for model-based control, yet remains challenging under distributional shifts and real-time constraints. In this work, we formulate system identification as an in-context meta-learning problem and compare deterministic and generative sequence models for forward dynamics prediction. We take a Transformer-based meta-model, as a strong deterministic baseline, and introduce to this setting two complementary diffusion-based approaches: (i) inpainting diffusion (Diffuser), which learns the joint input-observation distribution, and (ii) conditioned diffusion models (CNN and Transformer), which generate future observations conditioned on control inputs. Through large-scale randomized simulations, we analyze performance across in-distribution and out-of-distribution regimes, as well as computational trade-offs relevant for control. We show that diffusion models significantly improve robustness under distribution shift, with inpainting diffusion achieving the best performance in our experiments. Finally, we demonstrate that warm-started sampling enables diffusion models to operate within real-time constraints, making them viable for control applications. These results highlight generative meta-models as a promising direction for robust system identification in robotics.

Simulation trained legged locomotion policies often exhibit performance loss on hardware due to dynamics discrepancies between the simulator and the real world, highlighting the need for approaches that adapt the simulator itself to better match hardware behavior. Prior work typically quantify these discrepancies through precise, time-aligned matching of joint and base trajectories. This process requires motion capture, privileged sensing, and carefully controlled initial conditions. We introduce a practical alternative based on proprioceptive distribution matching, which compares hardware and simulation rollouts as distributions of joint observations and actions, eliminating the need for time alignment or external sensing. Using this metric as a black-box objective, we explore adapting simulator dynamics through parameter identification, action-delta models, and residual actuator models. Our approach matches the parameter recovery and policy-performance gains of privileged state-matching baselines across extensive sim-to-sim ablations on the Go2 quadruped. Real-world experiments demonstrate substantial drift reduction using less than five minutes of hardware data, even for a challenging two-legged walking behavior. These results demonstrate that proprioceptive distribution matching provides a practical and effective route to simulator adaptation for sim-to-real transfer of learned legged locomotion.

Accurate actuation models are critical for bridging the gap between simulation and real robot behavior, yet obtaining high-fidelity actuator dynamics typically requires dedicated test stands and torque sensing. We present a trajectory-based actuator identification method that uses differentiable simulation to fit system-level actuator models from encoder motion alone. Identification is posed as a trajectory-matching problem: given commanded joint positions and measured joint angles and velocities, we optimize actuator and simulator parameters by backpropagating through the simulator, without torque sensors, current/voltage measurements, or access to embedded motor-control internals. The framework supports multiple model classes, ranging from compact structured parameterizations to neural actuator mappings, within a unified optimization pipeline. On held-out real-robot trajectories for a high-gear-ratio actuator with an embedded PD controller, the proposed torque-sensor-free identification achieves much tighter trajectory alignment than a supervised stand-trained baseline dominated by steady-state data, reducing mean absolute position error from 14.20 mrad to as low as 7.54 mrad (1.88 times). Finally, we demonstrate downstream impact for the same actuator class in a real-robot locomotion study: training policies with the refined actuator model increases travel distance by 46% and reduces rotational deviation by 75% relative to the baseline.

Tendon drives paired with soft muscle actuation enable faster and safer robots while potentially accelerating skill acquisition. Still, these systems are rarely used in practice due to inherent nonlinearities, friction, and hysteresis, which complicate modeling and control. So far, these challenges have hindered policy transfer from simulation to real systems. To bridge this gap, we propose a sim-to-real pipeline that learns a neural network model of this complex actuation and leverages established rigid body simulation for the arm dynamics and interactions with the environment. Our method, called Generalized Actuator Network (GenAN), enables actuation model identification across a wide range of robots by learning directly from joint position trajectories rather than requiring torque sensors. Using GenAN on PAMY2, a tendon-driven robot powered by pneumatic artificial muscles, we successfully deploy dynamic but precise goal-reaching, ball-in-a-cup, and table tennis policies, trained entirely in simulation. To the best of our knowledge, this result constitutes the first successful sim-to-real transfer for a four-degrees-of-freedom muscle-actuated robot arm.

Accurate dynamics models are critical for the design of predictive controllers for autonomous mobile robots. Physics-based models are often too simple to capture relevant real-world effects, while data-driven models are data-intensive and slow to train. We introduce an approach for fast adaptation of neural robot dynamic models that combines offline training with efficient online updates. Our approach learns an incremental neural dynamics model offline and performs low-rank second-order parameter adaptation online, enabling rapid updates without full retraining. We demonstrate the approach on a real quadrotor robot, achieving robust predictive tracking control in novel operational conditions.

In recent years, the integration of additive manufacturing (AM) and industrial robotics has opened new perspectives for the production of complex components, particularly in the automotive sector. Robot-assisted additive manufacturing processes overcome the dimensional and kinematic limitations of traditional Cartesian systems, enabling non-planar deposition and greater geometric flexibility. However, the increasing dynamic complexity of robotic manipulators introduces challenges related to precision, control, and error prediction. This work proposes a model-based approach equipped with an integrated identification procedure of the system's parameters, including the robot, the actuators and the controllers. We show that the integrated modeling procedure allows to obtain a reliable dynamic model even in the presence of sensory and programming limitations typical of collaborative robots. The manipulator's dynamic model is identified through an integrated five step methodology: starting with geometric and inertial analysis, followed by friction and controller parameters identification, all the way to the remaining parameters identification. The proposed procedure intrinsically ensures the physical consistency of the identified parameters. The identification approach is validated on a real world case study involving a 6-Degrees-Of-Freedom (DoFs) collaborative robot used in a thermoplastic extrusion process. The very good matching between the experimental results given by actual robot and those given by the identified model shows the potential enhancement of precision, control, and error prediction in Robot Assisted 3D Printing Processes.

Autonomous proximity operations, such as active debris removal and on-orbit servicing, require high-fidelity relative navigation solutions that remain robust in the presence of parametric uncertainty. Standard estimation frameworks typically assume that the target spacecraft's mass properties are known a priori; however, for non-cooperative or tumbling targets, these parameters are often unknown or uncertain, leading to rapid divergence in model-based propagators. This paper presents an augmented Unscented Kalman Filter (UKF) framework designed to jointly estimate the relative 6-DOF pose and the full inertia tensor of a non-cooperative target spacecraft. The proposed architecture fuses visual measurements from monocular vision-based Convolutional Neural Networks (CNN) with depth information from LiDAR to constrain the coupled rigid-body dynamics. By augmenting the state vector to include the six independent elements of the inertia tensor, the filter dynamically recovers the target's normalized mass distribution in real-time without requiring ground-based pre-calibration. To ensure numerical stability and physical consistency during the estimation of constant parameters, the filter employs an adaptive process noise formulation that prevents covariance collapse while allowing for the gradual convergence of the inertial parameters. Numerical validation is performed via Monte Carlo simulations, demonstrating that the proposed Augmented UKF enables the simultaneous convergence of kinematic states and inertial parameters, thereby facilitating accurate long-term trajectory prediction and robust guidance in non-cooperative deep-space environments.

The identification of dynamic parameters in mechanical systems is important for improving model-based control as well as for performing realistic dynamic simulations. Generally, when identification techniques are applied only a subset of so-called base parameters can be identified. More even, some of these parameters cannot be identified properly given that they have a small contribution to the robot dynamics and hence in the presence of noise in measurements and discrepancy in modeling, their quality of being identifiable decreases. For this reason, a strategy for dynamic parameter identification of fully parallel robots in terms of a subset called relevant parameters is put forward. The objective of the proposed methodology is to start from a full dynamic model, then simplification concerning the geometry of each link and, the symmetry due to legs of fully parallel robots, are carried out. After that, the identification is done by Weighted Least Squares. Then, with statistical considerations the model is reduced until the physical feasibility conditions are met. The application of the propose strategy has been experimentally tested on two difierent configurations of actual 3-DOF parallel robots. The response of the inverse and forward dynamics of the identified models agrees with experiments. In order to evaluate the forward dynamics response, an approach for obtaining the forward dynamics in terms of the relevant parameters is also proposed.

Humanoid robots deployed in real-world scenarios often need to carry unknown payloads, which introduce significant mismatch and degrade the effectiveness of simulation-to-reality reinforcement learning methods. To address this challenge, we propose a two-stage gradient-based system identification framework built on the differentiable simulator MuJoCo XLA. The first stage calibrates the nominal robot model using real-world data to reduce intrinsic sim-to-real discrepancies, while the second stage further identifies the mass distribution of the unknown payload. By explicitly reducing structured model bias prior to policy training, our approach enables zero-shot transfer of reinforcement learning policies to hardware under heavy-load conditions. Extensive simulation and real-world experiments demonstrate more precise parameter identification, improved motion tracking accuracy, and substantially enhanced agility and robustness compared to existing baselines. Project Page: https://mwondering.github.io/halo-humanoid/

Robot model identification is commonly performed by least-squares regression on inverse dynamics, but existing formulations measure residuals directly in coordinate force space and therefore depend on the chosen coordinate chart, units, and scaling. This paper proposes a coordinate-independent identification method that weights inverse-dynamics residuals by the dual metric induced by the system Riemannian metric. Using the force--velocity vector--covector duality, the dual metric provides a physically meaningful normalization of generalized forces, pulling coordinate residuals back into the ambient mechanical space and eliminating coordinate-induced bias. The resulting objective remains convex through an affine-metric and Schur-complement reformulation, and is compatible with physical-consistency constraints and geometric regularization. Experiments on an inertia-dominated Crazyflie--pendulum system and a drag-dominated LandSalp robot show improved identification accuracy, especially on shape coordinates, on both downsampled and full datasets.

The da Vinci Research Kit (dVRK) has been widely used for research in robot-assisted surgery over the past decade, and its latest generation, the dVRK-Si was made publicly available in 2025. This manuscript presents the first complete kinematic and dynamic modeling framework for the dVRK-Si Patient-Side Manipulator (PSM), whose redesigned mechanism differs substantially from that of the first-generation dVRK and therefore requires a new formulation to accurately capture gravitational effects and improve overall control performance. We first develop a modified DH kinematic model that represents the dVRK-Si PSM's redesigned mechanism. The equations of motion are then derived using the Euler-Lagrange formulation, and the inverse dynamics are expressed in a linear-in-parameters regressor form. The dynamic parameters are identified from data collected along a periodic excitation trajectory optimized for numerical conditioning and estimated by convex optimization subject to the physical feasibility constraints. The identified model is integrated into the dVRK control stack to enable real-time gravity compensation and computed-torque feedforward control. Experiments on a physical dVRK-Si demonstrate that the gravity compensation reduces steady-state joint errors by up to 84% and decreases end-effector tip drift during static holds from 4.2 mm to 0.7 mm. Computed-torque feedforward control further improves transient and trajectory-tracking accuracy. During sinusoidal trajectory tracking, computed-torque feedforward reduces position errors by 35% versus gravity-only feedforward and by 40% versus PID-only. The proposed pipeline could support reliable control, high-fidelity simulation, and learning-based automation on the dVRK-Si.

Accurate and adaptive dynamic models are critical for underwater vehicle-manipulator systems where hydrodynamic effects induce time-varying parameters. This paper introduces a novel uncertainty-aware adaptive dynamics model framework that remains linear in lumped vehicle and manipulator parameters, and embeds convex physical consistency constraints during online estimation. Moving horizon estimation is used to stack horizon regressors, enforce realizable inertia, damping, friction, and hydrostatics, and quantify uncertainty from parameter evolution. Experiments on a BlueROV2 Heavy with a 4-DOF manipulator demonstrate rapid convergence and calibrated predictions. Manipulator fits achieve R2 = 0.88 to 0.98 with slopes near unity, while vehicle surge, heave, and roll are reproduced with good fidelity under stronger coupling and noise. Median solver time is approximately 0.023 s per update, confirming online feasibility. A comparison against a fixed parameter model shows consistent reductions in MAE and RMSE across degrees of freedom. Results indicate physically plausible parameters and confidence intervals with near 100% coverage, enabling reliable feedforward control and simulation in underwater environments.

The Crazyflie quadcopter is widely recognized as a leading platform for nano-quadcopter research. In early 2025, the Crazyflie Brushless was introduced, featuring brushless motors that provide around 50% more thrust compared to the brushed motors of its predecessor, the Crazyflie 2.1. This advancement has opened new opportunities for research in agile nano-quadcopter control. To support researchers utilizing this new platform, this work presents a dynamics model of the Crazyflie Brushless and identifies its key parameters. Through simulations and hardware analyses, we assess the accuracy of our model. We furthermore demonstrate its suitability for reinforcement learning applications by training an end-to-end neural network position controller and learning a backflip controller capable of executing two complete rotations with a vertical movement of just 1.8 meters. This showcases the model's ability to facilitate the learning of controllers and acrobatic maneuvers that successfully transfer from simulation to hardware. Utilizing this application, we investigate the impact of domain randomization on control performance, offering valuable insights into bridging the sim-to-real gap with the presented model. We have open-sourced the entire project, enabling users of the Crazyflie Brushless to swiftly implement and test their own controllers on an accurate simulation platform.

Simulation provides a cost-effective and flexible platform for data generation and policy learning to develop robotic systems. However, bridging the gap between simulation and real-world dynamics remains a significant challenge, especially in physical parameter identification. In this work, we introduce a real-to-sim-to-real engine that leverages the Gaussian Splat representations to build a differentiable engine, enabling object mass identification from real-world visual observations and robot control signals, while enabling grasping policy learning simultaneously. Through optimizing the mass of the manipulated object, our method automatically builds high-fidelity and physically plausible digital twins. Additionally, we propose a novel approach to train force-aware grasping policies from limited data by transferring feasible human demonstrations into simulated robot demonstrations. Through comprehensive experiments, we demonstrate that our engine achieves accurate and robust performance in mass identification across various object geometries and mass values. Those optimized mass values facilitate force-aware policy learning, achieving superior and high performance in object grasping, effectively reducing the sim-to-real gap.

Mimicking the graceful motion of swimming animals remains a core challenge in soft robotics due to the complexity of fluid-structure interaction and the difficulty of controlling soft, biomimetic bodies. Existing modeling approaches are often computationally expensive and impractical for complex control or reinforcement learning needed for realistic motions to emerge in robotic systems. In this work, we present a tendon-driven fish robot modeled in an efficient underwater swimmer environment using a simplified, stateless hydrodynamics formulation implemented in the widespread robotics framework MuJoCo. With just two real-world swimming trajectories, we identify five fluid parameters that allow a matching to experimental behavior and generalize across a range of actuation frequencies. We show that this stateless fluid model can generalize to unseen actuation and outperform classical analytical models such as the elongated body theory. This simulation environment runs faster than real-time and can easily enable downstream learning algorithms such as reinforcement learning for target tracking, reaching a 93% success rate. Due to the simplicity and ease of use of the model and our open-source simulation environment, our results show that even simple, stateless models -- when carefully matched to physical data -- can serve as effective digital twins for soft underwater robots, opening up new directions for scalable learning and control in aquatic environments.

Calibrating a robot simulator's physics parameters (friction, damping, material stiffness) to match real hardware is often done by hand or with black-box optimizers that reduce error but cannot explain which physical discrepancies drive the error. When sensing is limited to external cameras, the problem is further compounded by perception noise and the absence of direct force or state measurements. We present Vid2Sid, a video-driven system identification pipeline that couples foundation-model perception with a VLM-in-the-loop optimizer that analyzes paired sim-real videos, diagnoses concrete mismatches, and proposes physics parameter updates with natural language rationales. We evaluate our approach on a tendon-actuated finger (rigid-body dynamics in MuJoCo) and a deformable continuum tentacle (soft-body dynamics in PyElastica). On sim2real holdout controls unseen during training, Vid2Sid achieves the best average rank across all settings, matching or exceeding black-box optimizers while uniquely providing interpretable reasoning at each iteration. Sim2sim validation confirms that Vid2Sid recovers ground-truth parameters most accurately (mean relative error under 13% vs. 28--98%), and ablation analysis reveals three calibration regimes. VLM-guided optimization excels when perception is clean and the simulator is expressive, while model-class limitations bound performance in more challenging settings.

We introduce a Bayesian system identification (SysID) framework for jointly estimating robot's state trajectories and physical parameters with high accuracy. It embeds physically consistent inverse dynamics, contact and loop-closure constraints, and fully featured joint friction models as hard, stage-wise equality constraints. It relies on energy-based regressors to enhance parameter observability, supports both equality and inequality priors on inertial and actuation parameters, enforces dynamically consistent disturbance projections, and augments proprioceptive measurements with energy observations to disambiguate nonlinear friction effects. To ensure scalability, we derive a parameterized equality-constrained Riccati recursion that preserves the banded structure of the problem, achieving linear complexity in the time horizon, and develop computationally efficient derivatives. Simulation studies on representative robotic systems, together with hardware experiments on a Unitree B1 equipped with a Z1 arm, demonstrate faster convergence, lower inertial and friction estimation errors, and improved contact consistency compared to forward-dynamics and decoupled identification baselines. When deployed within model predictive control frameworks, the resulting models yield measurable improvements in tracking performance during locomotion over challenging environments.

We present $multipanda\_ros2$, a novel open-source ROS2 architecture for multi-robot control of Franka Robotics robots. Leveraging ros2 control, this framework provides native ROS2 interfaces for controlling any number of robots from a single process. Our core contributions address key challenges in real-time torque control, including interaction control and robot-environment modeling. A central focus of this work is sustaining a 1kHz control frequency, a necessity for real-time control and a minimum frequency required by safety standards. Moreover, we introduce a controllet-feature design pattern that enables controller-switching delays of $\le 2$ ms, facilitating reproducible benchmarking and complex multi-robot interaction scenarios. To bridge the simulation-to-reality (sim2real) gap, we integrate a high-fidelity MuJoCo simulation with quantitative metrics for both kinematic accuracy and dynamic consistency (torques, forces, and control errors). Furthermore, we demonstrate that real-world inertial parameter identification can significantly improve force and torque accuracy, providing a methodology for iterative physics refinement. Our work extends approaches from soft robotics to rigid dual-arm, contact-rich tasks, showcasing a promising method to reduce the sim2real gap and providing a robust, reproducible platform for advanced robotics research.