Reconfigurable Intelligent Surfaces

Maritime Air-to-Sea links are dominated by a line-of-sight ray and a sea-surface reflected ray whose destructive combination produces deep fades. Existing mitigation strategies optimize Unmanned Aerial Vehicle position or trajectory but leave attitude unexploited. This paper treats the full three dimensional attitude as a physical-layer control variable that shapes the two-ray interference through antenna phase-center displacement. Under small-angle and far-field assumptions, the constructive-interference condition reduces to an affine constraint in the Euler angles and admits a closed-form family of minimum-norm attitude candidates. A differentiable soft-minimum rule yields a smooth reference tracked by a constrained Nonlinear Model Predictive Control controller on a fully-actuated tilting multirotor. The proposed scheme increases cumulative throughput by 11.4% over a pitch-only benchmark and 22.2% over a zero-orientation baseline, while preserving trajectory tracking and respecting actuator limits.

Cylindrical watertight enclosures are widely used across various underwater systems, from unmanned underwater vehicles (UUVs), to remotely operated vehicles (ROVs), to various sensor platforms. However, electronics are typically built on rectangular PCBs arranged in horizontal stacks, which inefficiently occupy the circular cross-section volume that is critical for both payload capacity and buoyancy management. This paper presents CUB (Central Utility Board) and CougarTail, a general-purpose system designed to address this gap. CUB is a circular PCB sized for 4-inch-diameter enclosures that consolidates a Raspberry Pi Compute Module 5 (CM5) and an STM32 microcontroller, while also providing power management features and auxiliary connections. Mounted coaxially, CUB reduces the electronics stack of our CougUV from 200 mm of tube length and 709 g to 25 mm and 156 g, returning that length and mass budget to payload and buoyancy trim. CougarTail is an open-source companion sensor mast that houses a GPS antenna and two dual-band (2.4 and 5 GHz) omnidirectional PCB antennas. Both components are validated through bench testing and integration on a CougUV platform, our small open-sourced torpedo UUVs.

This paper studies unmanned aerial vehicle (UAV)-mouted reconfigurable intelligent surface (RIS)-assisted device-to-device (D2D) communication with stochastic link activation. It models UAV motion and attitude, time-varying Rician angles, and angle-dependent RIS reflection. A joint optimization of UAV trajectory, attitude, and RIS phases is formulated to maximize average sum rate under mobility, energy, and hardware constraints. The problem is addressed using deep reinforcement learning and a Decision Transformer trained on expert trajectories from multiple scenarios. Results demonstrate effective cross-scenario generalization, with zero-shot transfer outperforming direct DRL transfer and online fine-tuning achieving competitive performance with fewer interactions.

Automatic modulation classification (AMC) models are frequently trained and validated on synthetic or channel-cabled data, leaving open the question of how they behave once path loss and antenna pointing error are introduced by a genuine free-space link. We report a curriculum fine-tuning study of a hybrid CNN-Transformer AMC model. The general-purpose, all-32-class dataset underlying the model was built entirely at 915 MHz, on a controlled, clock/PPS-synchronized MIMO-expansion-cable link (not spatial-multiplexing transmission); all subsequent free-space, real-hardware experimentation - the sequential fine-tuning curriculum, matched-distance evaluation, and every reported over-the-air accuracy figure - was carried out at 4 GHz, across five directional-antenna distances (25, 35, 50, 70, 75 cm) under fixed TX/RX gain. Three distances used near-ideal antenna alignment (~99%) and two used a deliberately introduced partial misalignment (~85%), fine-tuned last in the curriculum. We report matched-distance test accuracy (91.8-93.7% across all five 4 GHz conditions) and confusion-matrix analysis grounded in RF theory, and report honestly where our sequential fine-tuning order confounds cumulative link adaptation with antenna alignment, rather than overstating what the data can support.

Future wireless systems are expected to transform the surrounding space from a passive propagation medium into a smart electromagnetic environment, where engineered surfaces control wave propagation, support wireless sensing, and create programmable electromagnetic fingerprints. A key challenge in realizing this vision is the inverse design of metasurfaces for tailored electromagnetic propagation. While forward analysis evaluates the response of a known geometry, the inverse task starts from a prescribed scattering signature and seeks a physically realizable structure that produces it. This inverse task is inherently nonlinear and often high-dimensional, while candidate solutions may be non-unique and provide no direct indication of practical realizability. Here, we introduce a conditional diffusion framework for inverse design of dielectric resonator metasurfaces from target angular scattering patterns. Trained on T-matrix simulated geometry-response pairs, the model learns a conditional distribution of geometries instead of a deterministic mapping, enabling multiple candidate designs for the ill-posed inverse problem. The best generated metasurface achieves a mean percentage error of 1.39%, outperforming CMA-ES optimization (4.1% after 10 h) while requiring only about one minute for after-training inference. The model also produces lower error distributions than deterministic neural baselines for out-of-distribution spectra, highlighting the potential of diffusion models for efficient metasurface design.

Accurate user equipment (UE) localization is critical for beam management in reconfigurable intelligent surface (RIS)-assisted millimeter-wave (mmWave) based sixth-generation (6G) networks, especially if the direct base-station-UE links are unavailable. This paper proposes a beam-domain fingerprint framework that maps the received signal-to-noise ratio (SNR) across a small set of predefined RIS reflection states to the UE azimuth angle and range, without requiring channel state information (CSI). Crucially, we extend the framework to a realistic interference-impaired scenario in which a nearby cross-link interferer (CLI) corrupts the clean SNR fingerprint, yielding a signal-to-interference-plus-noise ratio (SINR) fingerprint; an interference-to-noise ratio (INR)-constrained calibration strategy keeps the interference level physically interpretable. Four machine-learning (ML) regressors are evaluated under both conditions. Simulation results at 28 GHz with a 20x20 RIS show that k-nearest neighbors (KNN) achieves the lowest angle MAE of 0.37 degrees and range MAE of 4 cm under clean conditions, rising to 1.4 degrees and 7.6 cm under interference. A key finding is that interference degrades angle estimation substantially more than range estimation across all models, a consequence of the asymmetric encoding of location information in the beam-domain fingerprint.

Microwave ablation (MWA) is a promising minimally invasive treatment for liver tumors, but its therapeutic outcome strongly depends on patient-specific planning of antenna insertion trajectory, power, and treatment duration. Accurate numerical simulation can provide physically reliable ablation predictions; however, its high computational cost limits its use in optimization-based planning, where repeated forward evaluations are required. To address this issue, we propose a digital twin-based automatic planning framework that combines a neural ablation prediction model with a genetic algorithm. The model was trained on multiphysics simulation data generated from patient-specific tumor and vessel structures, antenna configurations, and treatment conditions, and was used as a fast forward model during planning. The prediction model achieved a Dice score of 95.1%, enabling accurate deep learning-based optimization. In 13 unseen planning cases, the proposed method improved ablation efficiency by 54.3% and reduced organ damage by 55.0% compared with clinician-defined planning, while slightly shortening the insertion path length by 3.3%. Most generated plans were also judged clinically applicable by MWA specialists. Furthermore, the framework enabled approximately 420-fold faster planning than numerical-simulation-based planning, demonstrating its potential as a fast digital twin for quantitative and personalized MWA treatment planning. The code is available at: https://github.com/SeonAengCho/MWA-Planning.git

Active beyond-diagonal reconfigurable intelligent surfaces (BD-RISs) enables hybrid transmitting and reflecting mode to achieve effective signal amplification and full-space coverage, thus providing a promising solution for blockage-aware uplink offloading in heterogeneous mobile edge computing (MEC) systems. However, practical hybrid mode active BD-RIS are realized by reciprocal devices, which inherently generate cross-sector energy leakage that will reshape the system-level energy-latency tradeoff. This paper studies energy-aware offloading and resource allocation for reciprocal active BD-RIS-assisted heterogeneous MEC, where offloading decisions, CPU/GPU computation allocation, transmit powers, receive processing, and active BD-RIS are tightly coupled. The resulting problem is a high-dimensional mixed integer nonconvex problem and is difficult to solve efficiently by conventional per-instance optimization. To address this challenge, we develop an end-to-end joint optimization framework based on a refined version of the distributional soft actor--critic algorithm, named as DSAC-T. By modeling return distributions rather than only expected values, DSAC-T improves policy stability under reward heterogeneity and feasibility-boundary sensitivity. Compared with other baseline algorithms, DSAC-T achieves the best energy-latency reward, the highest feasibility ratio of 81.67%, and a fast online decision time of 0.0267 s per scenario.

This paper investigates over-the-air federated learning (AirFL) in wireless systems where the access point is equipped with a multi-waveguide pinching antenna system (PASS). We adopt the widely studied learning-oriented AirFL formulation, which seeks to maximize the number of selected devices while keeping the aggregation distortion below a prescribed threshold. The resulting joint optimization of device selection, receive beamforming, and pinching-antenna placement is highly nonconvex due to the intricate coupling among these system variables. To address this challenge, we develop AirPASS, an alternating optimization framework with two main components: a homotopy-Riemannian margin-consolidation method for device selection and receive beamforming under fixed PASS configuration, and a homotopy-assisted geometry optimization method for updating the pinching-antenna positions under fixed selected devices and beamformer. Experiments show that AirPASS consistently outperforms conventional co-located MIMO baselines, remains close to ideal FedAvg, and achieves an attractive performance-complexity tradeoff relative to SDR-DC and matching-pursuit scheduling alternatives.

Radio frequency fingerprint identification (RFFI) exploits transmitter-specific hardware imperfections as physicallayer identity cues for Internet of Things (IoT) devices, but deep models often degrade across acquisition environments. In multi-antenna reception, antenna topology and frequencyoffset dynamics structure receiver observations, while capturedependent variation distorts target embeddings and misaligns source-trained decision boundaries. This article proposes physicsinformed structure anchoring with capture-aware prototype calibration (PISA-CAPC) to address both representation and decision mismatches. The two stages separate source representation construction from target decision correction. During source training, PISA organizes antenna tokens through a topology-guided graph, conditions propagation on CFO-derived acquisition dynamics, and applies bounded contextual residual suppression to preserve identity evidence. At deployment, unlabeled capture-aware prototype calibration (U-CAPC) estimates capture-local prototypes and recalibrates target decision scores while keeping the representation and source classifier fixed. Thus, calibration uses neither target labels nor target-domain backbone updates. On a measured WiFi benchmark with four receive antennas and ten transmitters, PISA-CAPC achieves a mean target-domain Macro-F1 of 0.9257 under a balanced transductive setting. Component ablations support complementary roles for topology-guided anchoring, CFO-conditioned modulation, reliability-aware token aggregation, contextual suppression, and capture-aware calibration. These results indicate that physically motivated representation learning can be combined with labelfree decision calibration to improve cross-environment RFFI under the evaluated protocol without changing the deployed backbone.

This paper studies energy efficient tracking of power-limited mobile users with the assistance of a Reconfigurable Intelligent Surface (RIS). Since localization pilot transmissions dominate the energy budget of power-constrained devices, we introduce a low-overhead feedback link from the Base Station (BS) to the user to enable dynamic uplink power control. To navigate the discrete and decentralized nature of this active sensing problem, we propose a novel Dual-Agent (DA) deep learning framework that jointly optimizes the discrete RIS phase profiles and the UE's transmit power in real time. Specifically, our approach employs a hybrid training methodology integrating the neuroevolution paradigm with supervised learning, effectively overcoming the non-differentiability of discrete phase responses from the RIS unit elements and the strict information bottleneck of single-bit feedback messages for pilot power control. The proposed DA active sensing framework can be applied with both single- and multi-antenna BSs, the latter with only minor modifications in the structure of one NN: an additional output branch with appropriate structure is included for the latter case to select a valid digital combiner from a finite set. Extensive numerical simulations demonstrate that the proposed scheme achieves highly accurate and robust tracking across diverse target motion models, outperforming extended Kalman and particle filters, as well as, machine learning-based trackers. Furthermore, in static localization, it is shown to significantly outperform traditional fingerprinting schemes, deep reinforcement learning baselines, and standard backpropagation-based estimators.

Accurately explaining hidden patterns in multi-aspect data has typically been done by leveraging labels and/or accompanying auxiliary metadata. However, labels and auxiliary data may be inaccurate (e.g. nonstandard, inconsistent), insufficient (e.g. static tabular metadata for time-dependent recordings), or unavailable. % We propose \fullmethod (\method), which leverages the knowledge of large language models (LLMs) to explain the hidden patterns in human narratives. \method uses task-agnostic and task-specific prompts to explain extracted co-clustered latent patterns from tensor decomposition. To evaluate these explanations, we test the LLMs on forward and backward inference tasks. % Our demo system is available at https://github.com/dawonahn/ECML_PKDD_AnTenA.

Predicting electromagnetic field (EMF) strength in urban environments is essential for cellular network planning but computationally expensive with physics-based simulators. We propose a multi-conditioned dense prediction framework that generates 500 500 EMF maps from building layout images and antenna configurations. Our architecture uses a High-Resolution Transformer (HRFormer) backbone with two complementary conditioning mechanisms: Feature-wise Linear Modulation (FiLM) injects scalar antenna parameters into all backbone stages, while cross-attention fuses 1-D radiation pattern tokens with spatial features at the deepest stage. We further introduce transmitter-relative spatial channels encoding distance, proximity, and bearing from the antenna, enabling coordinate-consistent test-time augmentation (TTA) that reduces test MAE by 6.3%. To address the prediction difficulty imbalance across EMF maps, we design a composite loss combining masked L1, multi-scale structural similarity (MS-SSIM), and a focal L1 term that upweights high-signal pixels, outperforming individual loss components in all metrics. Our best model achieves a test MAE of 0.0461, a 25.2% improvement over a plain UNet baseline and 31.8% over an HRFormer-only baseline.Do-

Ubiquitous perception through RF signals is a pivotal opportunity for future technology: it enables personalized services such as smart living, remote healthcare, automated logistics or interaction through free-space gestures. The ubiquity of Wi-Fi and cellular networks presents a promising platform for the development of innovative sensing tools. Future standards will also introduce dedicated sensing features which, for example, will allow routers to work as frequency modulated continuous wave radios targeting radar applications. Most of the current chip designs support ad-hoc firmware for CSI extraction with MIMO arrangements of the transmitter (TX) and receiver (RX) antennas and OFDM subcarriers. The CSI describes the phase shift and amplitude attenuation of multiple propagation paths on each subcarrier. The latest IEEE 802.11be standard (Wi-Fi 7) offers a wider subcarrier bandwidth of 160MHz (up to 320MHz), providing at least 120 usable pilot subcarriers for CSI or CIR estimation. Additionally, Wi-Fi signals have been recently exploited to track daily human movements and behaviors, while Wi-Fi signal variations have been shown to differ between different people and can consequently be used for their re-identification.

We introduce a wavelength-addressable diffractive optical network that transforms illumination wavelength into a high-dimensional control parameter for arbitrarily programmable 2D beam steering. The proposed passive architecture comprises cascaded spatially optimized diffractive layers, jointly designed using deep learning, to rapidly map distinct wavelengths to predefined/desired output angles. Unlike conventional single-layer dispersive optical elements, which are physically restricted to 1D linear mapping, this framework harnesses complex wavefront transformations to utilize the illumination wavelength as an intrinsic addressing key for arbitrary 2D beam steering, eliminating the need for mechanical scanning or electronic phase control. We numerically demonstrate wavelength-controlled beam steering across 625 wavelength channels spanning 400-750 nm, realizing a 25 x 25 array of independently addressable beam positions with subwavelength positioning accuracy and high channel fidelity. Unlike conventional gratings, which constrain wavelength routing to a linear trajectory, the proposed diffractive network performs nonlocal wavefront transformations, enabling arbitrary wavelength-to-angle mappings across a 2D field of view. We further validate the proposed framework experimentally in both the terahertz and visible spectral regimes, demonstrating wavelength-multiplexed beam steering using 3D fabricated passive diffractive layers at terahertz frequencies and phase-only spatial light modulators in the visible spectrum. This wavelength-addressable diffractive architecture establishes a compact and scalable paradigm for high-speed programmable beam steering, with potential applications in optical communications, routing, imaging, sensing, and emerging photonic information-processing systems.

Wireless foundation models offer a path toward reusable channel state information (CSI) intelligence for sixth-generation (6G) systems. However, existing generic-backbone adaptation and CSI pretraining methods often treat CSI as task tensors rather than propagation-conditioned channel responses, thereby failing to capture the intrinsic time-frequency-spatial geometry of wireless environments. This paper presents a channel-adaptive roadmap toward CSI-native foundation models, proposing a unified framework that aligns pretraining, positional modeling, and attention control with three channel requirements: scale-aware heterogeneous exposure, physical time-frequency-antenna coordinates, and correlation-bounded token interaction. Extensive experiments demonstrate the superiority of the proposed framework across three dimensions: zero-shot generalization, reducing NMSE by more than 4 dB across spatial-temporal-frequency tasks; scale extrapolation, yielding up to a 5.4 dB gain under 8 times unseen antenna scaling; and inference efficiency, accelerating mobility-aware processing by up to 18.8%. A system-level evaluation with Sionna SYS further shows that the proposed framework uses only 7.01% of dense-pilot overhead, reaches -18.64 dB average NMSE, and improves average net spectral efficiency by 36.6% over dense LMMSE and 15.5% over WiFo, indicating that CSI-native representation learning can support pilot-efficient radio access.

CSI-based localization with spatially distributed antenna arrays exposes a basic resource trade-off. Each array can provide a rich view of the channel, but forwarding observations from all arrays to a fusion center is wasteful when only a few carry useful information, and the shared uplink supports only a limited number of simultaneous transmissions. We let each array decide locally whether its current observation is worth reporting, subject to a budget on the average number of active transmitters. We refer to this abstraction as Edge-Triggered Distributed Inference (ETDI). It captures a broader class of task-oriented communication problems where resource-constrained devices share an access channel for a common inference task. We instantiate ETDI for CSI-based localization, a common scenario in vehicular IoT networks. Spatially distributed remote antenna arrays (RAAs) encode local channel state information (CSI) from user equipment (UE) transmissions into latent features, and the fusion center estimates the UE position from the subset of reported features. We propose NARRAS, a decentralized reporting policy in which each RAA combines a recurrent summary of its recent observations with a memory of the last latent it transmitted. Training controls an explicit activity budget through differentiable activity penalties and validation-calibrated deterministic thresholds, and uses channel-chart regularization to shape the latent geometry. Experiments show that, at comparable uplink activity, NARRAS improves localization accuracy over learned and heuristic sparse-reporting strategies, while dense full-report models remain useful budget-free references. In low-activity regimes, chart regularization further reduces high-percentile localization errors, suggesting that geometry-aware latent representations are more robust under sparse reporting.

Human Activity Recognition (HAR) using WiFi signals has emerged as a transformative technology for smart homes, healthcare monitoring, security systems, and ambient assisted living. Unlike traditional camera-based systems that raise significant privacy concerns and fail in low-light conditions, or wearable sensors that require user compliance, WiFi-based HAR is non-intrusive, privacy-preserving, cost-effective, and works seamlessly in any lighting condition. This paper presents a comprehensive approach to recognize three distinct human activities: "No Presence" (empty room), "Walking", and "Walking + Arm-waving" using the Wallhack1.8k WiFi spectrogram dataset. We propose three key improvements to address the main challenges in WiFi-based HAR. First, to address high performance variance, we implement ensemble learning with five different CNN architectures (Deep CNN, Wide CNN, MobileNetV2, ResNet50V2, and EfficientNetB0). Second, to address the small dataset size limitation, we apply aggressive data augmentation techniques including time-warping, frequency masking, and noise addition. Third, to evaluate real-world generalization capability, we perform cross-scenario evaluation (training on Line-of-Sight and testing on Non-Line-of-Sight) and cross-antenna evaluation (training on Biquad antenna and testing on PIFA antenna). Our ensemble model achieved a test accuracy of 94.87% on the LOS scenario with Biquad antenna, outperforming the best individual model by 0.66%. Data augmentation improved Random Forest performance from 60% to 95%. Cross-scenario evaluation showed minimal accuracy drops of only 1.37% and 2.07%, demonstrating strong generalization capabilities. The results indicate that the proposed approach is robust, reliable, and suitable for real-world deployment in diverse environments with different hardware configurations.

Distributed space antennas using electromagnetic formation flight (EMFF) are a promising architecture for large-aperture, long-life space communication systems. Their feasible aperture, however, is governed by coupled constraints on antenna performance, satellite mass, power generation, coil geometry, and formation-keeping power. This paper proposes a system-level design framework for EMFF-based distributed space antennas. It links phased-array requirements with satellite-level sizing constraints and provides a static grid-based reference for designing feasible apertures under a fixed system mass. Unlike our previous bucket-brigade disturbance-compensation model, the formation-maintenance requirement is incorporated through a control index derived from distributed-control simulations. This index is integrated into an antenna-aperture maximization problem with sizing, power, coil, and sidelobe-envelope constraints. Parametric case studies examine margin magnetic moment, prescribed transmit power, and large inter-satellite spacing. Results show that increasing system mass improves footprint reduction or effective isotropic radiated power only while satellite-level design headroom remains. In direct-to-device cases with 0.15 m spacing, generated-power and coil-geometry constraints dominate the feasible aperture. In the 0.60 m large-spacing case, the required coil burden can exceed satellite-level mass, size, and power capacities, making the design infeasible despite favorable communication performance. The proposed framework enables the design and evaluation of feasible static grid-based EMFF distributed antennas under coupled antenna, satellite, and control constraints.

Intelligent Reflecting Surfaces (IRSs) are a promising technology for enhancing the spectral and energy efficiency of millimeter-wave (mmWave) multiple-input multiple-output (MIMO) systems. In these systems, accurate channel estimation remains challenging due to the passive nature of IRS elements and the high pilot overhead in large-scale deployments. This paper presents a deep learning-based Multi-Block Attention (MBA) framework for efficient cascaded channel estimation in IRS-assisted mmWave MIMO systems that utilize orthogonal frequency division multiplexing (OFDM). First, we show the optimality of the discrete Fourier transform (DFT) and Hadamard matrices as phase configurations for least squares (LS) estimation. To reduce training overhead, we selectively deactivate IRS elements and compensate for induced feature loss using a two-stage architecture: (i) a Convolutional Attention Network (CAN) for spatial correlation recovery and (ii) a Complex Multi-Convolutional Network (CMN) for noise suppression. The MBA architecture mitigates error propagation through attention-guided feature refinement and denoising. Simulation results indicate that the MBA method reduces pilot overhead by up to 87% compared to the LS estimator. Additionally, at signal-to-noise ratios of 10 dB, our proposed method achieves approximately 51% lower normalized mean squared error (NMSE) than leading methods. It also maintains low computational complexity and adapts effectively to various propagation environments.

This paper investigates coordinated downlink transmission in a multi-base station (multi-BS) multi-reconfigurable intelligent surface (multi-RIS)-assisted pinching-antenna (PA) system, where each user equipment (UE) is associated with a single BS and each BS is equipped with movable PAs deployed on parallel waveguides. We formulate sum rate (SR) and energy efficiency (EE) maximization problems by jointly optimizing PA placement, RIS phase shifts, transmit beamforming, and BS-UE association under constraints of inter-PA spacing, power budget, and unit-modulus phase shift. To address the resulting highly coupled mixed-variable problem, we propose a three-stage graph neural network (GNN) that integrates heterogeneous and homogeneous graph representations and is trained end-to-end in an unsupervised manner. Extensive numerical results demonstrate that the proposed three-stage GNN consistently outperforms representative system and learning baselines, generalizes well to unseen numbers of UEs, RISs, and BSs, and maintains millisecond-level inference time. Besides, the results validate the effectiveness of the proposed design from both system and architectural perspectives. Moreover, PAs are shown to enhance SR and EE, and the performance gain is enlarged with increasing number of PAs.

Multi-antenna receiving systems have become a prevalent technical solution in communication systems. Meanwhile, deep learning has achieved significant progress in automatic modulation recognition tasks in single-antenna systems. However, the application of deep learning in multi-antenna modulation recognition (MAMR) tasks is still limited. In this paper, we propose an MAMR method namely MAMR-IQ to fully explore the diversity gain of a multi-antenna receiving system, which concatenates the raw received in-phase and quadrature (IQ) signals of multiple antennas and feeds them into a convolutional neural network. Simulation results show that the proposed MAMR-IQ method outperforms two existing deep learning-based MAMR methods which are based on direct voting (DV) and weight average (WA) in terms of both recognition accuracy and computational complexity. To address the problem of limited training data in few-shot scenarios, we further propose a data augmentation method that involves exchanging IQ sequences received by any two antennas to generate augmented samples. Simulation results show that with the proposed augmentation method, the recognition accuracy can be further improved.

Reconfigurable intelligent surfaces (RISs) modify signal reflections to enhance wireless communication capabilities. Classical RIS phase optimization is highly non convex and challenging in dynamic environments due to high interference and user mobility. Here we propose a hierarchical multi-objective quantum metalearning algorithm that switches among specific quantum paths based on historical success, energy cost, and current data rate. Candidate RIS control directions are arranged as switch paths between quantum neural network layers to minimize inference, and a scoring mechanism selects the top performing paths per layer. Instead of merely storing past successful settings of the RIS and picking the closest match when a new problem is encountered, the algorithm learns how to select and recombine the best parts of different solutions to solve new scenarios. In our model, high-dimensional RIS scenario features are compressed into a quantum state using the tensor product, then superimposed during quantum path selection, significantly improving quantum computational advantage. Results demonstrate efficient performance with enhanced spectral efficiency, convergence rate, and adaptability.

Reconfigurable Intelligent Surfaces (RIS) have the potential to engineer smart radio environments for next-generation millimeter-wave (mmWave) networks. However, the prohibitive computational overhead of Channel State Information (CSI) estimation and the dimensionality explosion inherent in centralized optimization severely hinder practical large-scale deployments. To overcome these bottlenecks, we introduce a per-element CSI-free paradigm powered by a Hierarchical Multi-Agent Reinforcement Learning (HMARL) architecture to control mechanically reconfigurable reflective surfaces. By substituting pilot-based channel estimation for each element of the device with accessible user localization data, our framework leverages spatial intelligence for macro-scale wave propagation management. The control problem is decomposed into a two-tier neural architecture: a high-level controller executes temporally extended, discrete user-to-reflector allocations, while low-level controllers autonomously optimize continuous focal points using Multi-Agent Proximal Policy Optimization (MAPPO) under a Centralized Training with Decentralized Execution (CTDE) scheme. Comprehensive deterministic ray-tracing evaluations in an indoor mmWave scenario demonstrate that this hierarchical framework achieves received signal strength indicator (RSSI) improvements of up to 7.79 dB over centralized Proximal Policy Optimization (PPO) baselines. Furthermore, the system maintains resilient beam-focusing performance under practical sub-meter localization tracking errors for up to four users and two reflector arrays. By eliminating execution-time CSI overhead while preserving high-fidelity signal redirection, this work provides a scalable and cost-effective step toward intelligent indoor wireless environments.

The paper presents an approach for learning antenna Radiation Patterns (RPs) of a pair of heterogeneous quadrotor Uncrewed Aerial Vehicles (UAVs) by calibration flight data. RPs are modeled either as a Spherical Harmonics series or as a weighted average over inducing samples. Linear regression of polynomial coefficients enables decoupling of independent UAVs' RPs from the observed joint gain. A synchronized calibration trajectory provides training and testing samples in an obstacle-free anechoic altitude. Evaluation on a real-world dataset demonstrates the feasibility of learning both radiation patterns, achieving 4.56 dB RMS extrapolation error. The proposed RP learning and decoupling can be exploited in rapid recalibration upon payload changes, thereby enabling precise autonomous path planning and swarm control in real-world applications where setup changes are expected.

Efficient resource utilization is proposed for simultaneously transmitting and reflecting reconfigurable intelligent surfaces (STAR-RIS) to ensure fair and high data rates. We optimize the number of STAR-RIS elements to be allocated to each user and maximize the sum of the user rates. To promote fairness, we introduce a soft fairness mechanism that guarantees a minimum STAR-RIS element allocation to every user. Subject to this requirement, the phase shifts of the STAR-RIS elements and the remaining element assignments are jointly optimized by harnessing an appropriately tailored deep reinforcement learning (DRL) algorithm. The proposed DRL method is also compared to Dinkelbach's algorithm and to a bespoke hybrid DRL approach. A deactivation incentive is incorporated into the DRL model for enhancing resource utilization by intelligently deactivating some of the STAR-RIS elements when not required. The proposed DRL method achieves fair and high data rates for both stationary and mobile users, while ensuring efficient resource utilization. Using the proposed DRL method, up to 34% and 23% of STAR-RIS elements can be deactivated in static and mobile scenarios, respectively, with negligible degradation in the average DL data rate.