Gripper

Effective manipulation across diverse objects is critical for applications ranging from agricultural harvesting to laboratory and domestic automation. While the inherent compliance of soft robotics is well suited to this challenge, designing grippers that generalize across tasks remains difficult due to the vast design space of continuum mechanics and the risk of overfitting to specific scenarios. We propose a graph-based design space for representing soft structures and mechanisms, coupled with a multi-objective, diversity-driven genetic optimization framework that explicitly promotes solution variety throughout the design process. Using multiple grasping scenarios during optimization, we study how task diversity influences the emergence of generalization to unseen objects and contact conditions. Our results show that optimization over a sufficiently diverse set of grasping cases leads to designs with emergent generalization, exhibiting improved robustness compared to task-specific solutions on novel scenarios. These findings suggest that diversity-driven optimization offers a principled pathway toward general-purpose soft grippers, aligned with the adaptable nature of soft robotics.

Fresh-market blueberries require selective, gentle picking, which is labor-intensive and expensive. Over-the-row machine harvesters are fast but non-selective, bruising mixed-ripeness fruit and limiting yield to the processing market. Selective robotic harvesters typically target individual fruits rather than fruit clusters, which limits harvesting efficiency for small, densely clustered blueberries. This paper presents CLASP, a Cluster-Level Autonomous Selective Picking robot with a Soft Active Rolling-Band Gripper (SARB-Gripper). Two compliant bands envelop the cluster and roll against the fruit, drawing mature berries off in sequence, while closed-loop regulation of the pulling force keeps the applied load below the immature detachment threshold. A global-to-local perception pipeline pairs an eye-to-hand camera for global cluster detection and target selection with an eye-in-hand camera for local localization and cluster orientation estimation. Field measurements confirm a clear detachment-force separation between mature and immature fruit, and the SARB-Gripper reproduces a commanded pulling force to within \SI{3.7}{\percent}, enabling selective harvesting at the cluster level. In end-to-end field trials, CLASP autonomously grasped 23 of 25 presented clusters (\SI{92}{\percent}). With the component cost of approximately $3326 per unit, CLASP offers a scalable approach to selective cluster-level harvesting for fresh-market blueberries.

Robots are increasingly used in unstructured environments. The need for them to safely grasp unknown objects without damaging them becomes crucial. Humans achieve this by sensing and quickly responding by adjusting their grasping force. Similarly, effective grasp acquisition in robots requires compliant interaction strategies that can adapt to uncertain object properties and adjust to any instabilities during manipulation. We present a geometry-aware force/torque-based contact estimation method for a coarse position-controlled gripper, combined with an adaptive admittance controller for safe grasp acquisition. The desired contact forces are estimated online to keep stable contact with objects of unknown properties. This enables compliant and stable grasps while avoiding excessive forces. Experiments with objects of different sizes, shapes, stiffnesses, and weights show that the proposed algorithm not only prevents slippage but also applies minimal force to safely grasp an object without causing excessive deformation.

Robust grasping of everyday objects remains challenging for parallel-jaw grippers, particularly when handling sloped or asymmetric items that induce torque-driven rolling and shear slip. These challenges become even more severe in domestic environments such as kitchens, where objects are often wet or submerged, drastically reducing friction between the gripper and the object. To address these issues, we present a waterproof passive adaptive gripper that combines local and global adaptability for high-performance grasping in the submerged environments. The proposed gripper features a fully waterproof design that integrates a passive rotational joint for global self-alignment on sloped surfaces and passive variable-stiffness pads for local surface adaptation. Experiments in both dry and underwater conditions on various cylindrical and conical objects demonstrate superior holding capability and grasp robustness compared to rigid-pad and fixed-joint baselines. The proposed design offers a practical and robust solution that successfully enables stable underwater manipulation of diverse everyday objects, effectively addressing a critical gap in current underwater robotic grasping for daily-life applications.

Magnetic levitation (MagLev) systems have great potential for application in high-mix, low-volume manufacturing due to their scalability and flexibility, enabling highly reconfigurable in-machine material flow. However, their manipulation capabilities remain largely unexploited, as current applications almost exclusively focus on transportation. To enable grasping and manipulation directly on MagLev systems without requiring additional costly handling equipment, such as industrial robot arms, we present the Gripper MagBot, a low-cost parallel 6-DoF manipulator with an integrated 1-DoF gripper that mechanically couples three MagLev movers. The Gripper MagBot supports two operating configurations: a default mode and a single-track mode, selectable depending on the required stability and workspace footprint. To reconfigure a machine, the MagBot can be autonomously dropped off and picked up using a docking station. We showcase pick-and-place examples in simulation, as well as with the real Gripper MagBot using our inverse kinematics controller. CAD files, assembly instructions, a component list, and videos are available at https://sites.google.com/view/gripper-magbot.

Transferring human hand demonstrations to robotic grippers has recently emerged as a cost-effective solution for robot learning. However, existing methods are largely confined to simple, planar tasks and fail to handle complex spatial movements (e.g., intricate trajectories involving rotations or flips) that are essential for robot manipulation. Motivated by this gap, we adopt an implicit, data-driven approach guided by fine-grained hand-pose motions. To this end, we introduce a scalable acquisition pipeline to collect hand-gripper paired demonstrations, governed by a rigorous protocol that prioritizes motion complexity and leverages a handheld gripper for seamless action mimicry. This yields a large-scale paired dataset comprising 6,189 episodes across 1,254 unique objects, exhibiting significantly higher spatial complexity than existing benchmarks. However, learning such complex mappings remains challenging. We observe that naive end-to-end generation of full gripper pose sequences is insufficient, as minor trajectory deviations compound rapidly under intricate dynamics. To address this, we propose a two-stage framework: Stage I predicts sparse gripper keyframes (initial and terminal) to simplify the mapping objective, while Stage II generates the full continuous action sequence conditioned on these keyframes. Furthermore, to mitigate cumulative drift, we keep the gripper's orientation being learned while post-optimizing its translation based on the grasping heuristic and kinematic consistency. In both simulation and real-robot experiments, our framework enables stable and precise hand-to-gripper transfer of complex spatial manipulations, significantly outperforming traditional baselines. Project page: https://cosmoh2g.github.io.

This paper presents an end-to-end computational pipeline that converts a selected object mesh, a measured object state, and a selected six-axis robot into an object-specific, unactuated, additively manufacturable gripper. The method couples exact-mesh RGB-D/ICP pose registration, deterministic surface-contact sampling, uncertainty-aware wrench screening, selection among six passive capture mechanisms, object-conformal surface synthesis, full-orientation robot inverse kinematics, a swept-volume-aware manufacturing domain, directional fused-deposition finite-element screening, and constrained three-dimensional SIMP topology optimization. Unlike workflows that treat grasp selection, tool geometry, motion, and structural design as separate problems, every exported design is bound to the source mesh, object pose, robot flange, contact set, and insertion hypothesis by a traceable design identifier. We derive the implemented registration, contact, fit-tolerance, finite-element, and density-optimization equations and prove three properties of the numerical construction: nodal load preservation, monotonic compliance sensitivity under SIMP interpolation, and voxel-domain containment after topology post-processing. Four archived object-specific attempts - a rabbit, camera flange, 3DBenchy, and faceted bust - meet the nominal fit, uncertain-wrench, runtime-sweep, and baseline/post-topology FEA gates. A deliberately enlarged +/-3 mm, +/-5 degree pose stress check differentiates the designs, retaining 29-134 of 160 simulated trials. Their reconstructed topologies retain 92.0-97.6% of the FE domain because functional regions are protected. Archived robot photographs show the corresponding printed assemblies qualitatively, while nominal material properties and absent coupon-calibrated, instrumented tests keep all four at digital-screening status rather than operational release.

Grasping and holding tools while using them presents a considerable challenge not only for robots but also for humans. Such a challenge is particularly noticeable in processes involving assembly and disassembly, where efficiency and consistency depend on performing rapidly adaptive tasks. Nonetheless, contemporary robotic grasping technologies that can securely manipulate tools during operation frequently have significant constraints. In this paper, introduce ARTiS (Adaptive Robotic Tool Gripper in Disassembly Systems), a novel gripper that combines the adaptability of soft grippers, the dexterity of anthropomorphic hands, and the robustness of rigid mechanisms with a soft palm and fingertips. This unique combination makes it possible to hold tools securely in a variety of situations through using active jamming in the palm and fin-ray adaptation in fingertips. Furthermore, high finger dexterity is achieved through the seven degrees of freedom design, which enables the fingertips to orient to any surface, both for automated solutions and collaborative tasks. A comprehensive evaluation was conducted using a range of conventional disassembly tools to assess the gripper's compliance, durability, and functional versatility. More information, hardware instructions, and videos at https://romanmykhailyshyn.github.io/artis/

Augmenting the dexterity of human surgeons has the potential to free them from tedious subtasks. We consider debridement (removal of diseased or dead tissue fragments), which is challenging due to imprecision in spatial perception and cable actuation. We develop an augmented dexterity system for surgical debridement that uses visual servoing to align the cable-driven gripper with the target position in the image plane, and then introduces a novel approach to depth control, MACAW: Monocular Adaptive Compact Attention Windows. Across 100 physical trials using the da Vinci Research Kit (dVRK) robot, camera-frame servoing reduced average gripper position offset from 37 to fewer than 5 pixels within 4 optimization steps, taking an average of only 0.39s. MACAW significantly outperforms procedural and learned VLA baselines, achieving a 93% success rate at 11 seconds per fragment, yielding a throughput of 304 fragments per hour. Extending MACAW to a bimanual debridement setup maintains a 92% success rate at an average of 7 seconds per fragment, increasing the throughput to 473 fragments per hour.

This technical report describes the RMC2 Team's champion solution for the WBCD 2026 Track 4: Deformable Manipulation Challenge. The task requires a robot to pick a single T-shirt from a stack, load it onto a printing pallet, align the collar with a target area, and smooth the printing region, a sequence that involves single-layer separation, deformable transport, precise placement, and contact-rich surface adjustment. The competition strongly incentivizes fully autonomous execution, motivating the development of an autonomous solution. We built a fully autonomous system around the TCAM (TermiBrain Causal Action Model) framework, with the design principle that hardware, perception, data, and learning should jointly reduce the physical interaction complexity the policy must handle. A custom 3D-printed gripper designed for single-layer fabric separation improves picking reliability on a dual-arm ARX X5 platform. A wrist-centric four-camera setup pairs upper fisheye cameras for task-level context with lower RGB cameras for close-range gripper-cloth contact observation. We combine portable UMI-style demonstrations with real-robot demonstrations collected on the deployable platform to provide both broad manipulation priors and deployment-specific dynamics. TCAM ties these components into a closed loop: each trajectory is analyzed to identify the physical factors contributing to its outcome, driving targeted data recollection and policy fine-tuning. The policy outputs 30-step end-effector delta-pose action chunks from a multi-view VLA backbone. In the final competition, our system loaded 25 T-shirts at an average of approximately 23 seconds per attempt, with 22 achieving the required surface smoothness, securing first place in Track 4.

Conventional robotic grippers often use high-ratio transmissions to generate grasping torque and external force sensors to measure physical interaction. High-ratio transmissions increase friction, reflected inertia, and mechanical impedance, while external sensors add hardware complexity. To address these trade-offs, this study proposes a novel 9-DOF, three-fingered Differential Direct-Drive (DDD) gripper that combines DD motors with a low-ratio (1:2) differential transmission. The mechanism centralizes actuator mass at the base to minimize moving-link inertia, while the differential architecture couples two motors in parallel to amplify torque during flexion. Experiments show that the prototype delivers a nominal grasping force of approximately 18 N and a fingertip force of 4.7 N, while maintaining a low motor contribution to system inertia (0.236%) and low passive mechanical impedance, with a maximum measured value of 50.1 N/m when the motors are unpowered. The proposed hardware addresses the trade-offs among torque, physical transparency, and kinematic dexterity, providing a foundation for high-bandwidth interaction and sensorless proprioceptive force estimation.

Delicate manipulation often involves transient and subtle collisions between a grasped object and the environment. While the human hand localizes these contacts effortlessly thanks to superior tactile sensitivity, robotic systems often lack the requisite resolution to acquire the information necessary for motion planning, resulting in clumsy manipulation or even task failure. Here, we propose transient extrinsic contact detection and ranging (TECDAR), a simple yet fast and efficient method for detecting and ranging extrinsic contact of grasped objects. Our design of gripper tips employs dynamic tactile sensing leveraging a single 2.5$\times$3 mm 6D inertial measurement unit. The sensor captures sub-millisecond tip deformations at a 7 kHz sampling rate, but operating on a data stream of only 84 KB/s. High bandwidth and compact data size enable the system to rapidly detect and localize contact between grasped objects and their surroundings. Specifically, fusing tactile data with robot pose via an extended Kalman filter enables fast and precise localization of extrinsic contact, reaching millimeter-level accuracy within 180 ms. Experimental results demonstrate that the system achieves an average localization accuracy of approximately 7,mm in both line-contact and point-contact localization tasks. Furthermore, this near-instantaneous localization enables the robot to rectify its trajectory on a millisecond scale, facilitating precise tool manipulation and enhanced perception of complex environments purely through tactile exploration and mapping. We envision such techniques advancing the future of robotics across domains requiring delicate manipulation, including precision assembly, surgical assistance, and autonomous exploration in touch-dominant environments. Project page: humitlab.github.io/TECDAR/

Cross-embodiment dexterous grasping aims to synthesize stable grasps across heterogeneous multi-fingered hands with little or no embodiment-specific tuning. Existing interaction-centric methods achieve promising results, but their object representations often underrepresent local surface geometry, while their robot descriptors do not explicitly encode both robot morphology and kinematics. We propose MANGO-Grasp, an anisotropic interaction framework that represents objects as geometry-oriented 3D Gaussian primitives and robot hands as surface keypoints encoded into morpho-kinematic descriptors. The object primitives are adaptively allocated by geometric complexity and shaped as surface-aligned plates with outward normals, encoding local geometry. Mahalanobis fields over keypoint--primitive pairs serve as interaction prediction targets during training and as optimization guidance for grasp realization at inference. These fields rise sharply for displacement along the surface normal but only gently within the tangent plane, matching the directional structure of contact. Grasps are realized with one shared optimization formulation and hyperparameter setting across all embodiments. On the CMAP and MultiGripperGrasp benchmarks, MANGO-Grasp outperforms the strongest seen-hand baseline by up to 8.24 percentage points in simulation. It also transfers zero-shot to the unseen SharpaWave hand, improving over the strongest zero-shot baseline by up to 16.57 percentage points, and achieves 86% success in real-world experiments. The code and additional materials will be made available upon publication at https://connor-zh.github.io/MANGO-Grasp/.

Maintaining a stable pose during physical interaction is a significant challenge for aerial robots, often limiting their use in contact-based tasks. This paper presents a novel uncrewed aerial vehicle (UAV) platform designed to transition from unconstrained flight to a stable, constrained work platform via environmental anchoring. Our system comprises: 1) a multirotor with a tilt-rotor mechanism that decouples pitch from forward motion, enabling stable hover at non-zero pitch angles, and 2) a novel underactuated, cable-driven, prismatic gripper featuring compliance to adapt to irregular geometries, designed to stabilize the UAV by anchoring it to its environment. We present the design and prototyping of the complete system and validate its performance through a series of real-robot flight tests. Results demonstrate that anchoring significantly improves stability for interaction tasks, reducing positional drift RMSE by over 95% compared to a free-flight baseline, even under windy conditions. The anchored system can withstand longitudinal reaction forces up to 75N while maintaining a stable pose. Furthermore, across a range of target geometries and orientations, the system demonstrated consistent stability with a positional drift RMSE that never exceeded 3mm. These results establish the viability of our approach for complex physical interaction tasks, such as sampling tree health by drilling or sensor installation in hard-to-reach locations. Watch our UAV at: https://youtu.be/HDQ8S4ZW3Ls

Soft robots have seen widespread adoption in interactive tasks due to their inherent compliance and adaptability. However, these advantages often come at the cost of stability, posing challenges in a dynamic environment. This limitation is especially critical in soft grippers, where instability under acceleration or external disturbances can result in grasp failure. In this study, we present a continuously stable structure through plastic deformation (CSSPD), integrated into a soft gripper. By leveraging the mechanism of plastic deformation, the gripper maintains continuous configurations without energy input, while the added stiffness ensures both static and dynamic stability. We introduce a bioinspired paw pad that significantly enhances stability and enables sensing-based rapid object grasping. Then we develop the mathematical model and optimize the kirigami structure of the metal layer. Experimental results show that the gripper can sustain a passive holding force of up to 16 N without energy input, achieving performance comparable to pneumatic actuation at 0.3 MPa. When combined with pneumatic actuation, it remains stable under pulsed accelerations of up to 400 m/s^2. It can also passively perch on tree branches for extended periods without power, demonstrating promise for mobile robotic applications.

This paper presents a scalable, open-source visuotactile sensing system for tensegrity robots that enables six-axis wrench estimation and contact detection. The proposed endcap sensor integrates an elastomeric shell, a 3D-printed thermoplastic polyurethane (TPU) interface, and a rigid base housing an embedded camera and LED illumination ring. A novel gyroid-infill bonding technique is introduced to form a durable elastomer-TPU interface without adhesives, yielding a lightweight and modular design compatible with large-scale tensegrity structures. A tactile-to-wrench neural network maps shear vector fields to six-dimensional force and torque measurements. Experimental results demonstrate accurate and stable wrench estimation with a mean squared error (MSE) of 0.1531 on static validation data and out-of-domain generalization under dynamic motion. Furthermore, full-system integration on a 12 kg tensegrity robot confirms the sensor's ability to reliably identify ground contacts. The system substantially improves the practicality of tactile feedback for tensegrity robots, offering a low-cost, reproducible, and physically interpretable pathway toward contact-aware proprioception and state estimation. Open source files are available at \href{https://github.com/Jonathan-Twz/tensegrity-gelfoot}{github.com/Jonathan-Twz/tensegrity-gelfoot}

Conventional robotic grippers face a significant challenge in agricultural automation: the trade-off between compliant, adaptive grasping, pressure balancing among all joints, and high load capacity, often at the cost of high energy consumption. This paper presents a novel hybrid rigid-soft gripper that integrated low-cost, membrane-based pneumatic actuators with 3D-printed dual ratchet-pawl mechanisms to simultaneously achieve shape adaptation, uniform force distribution, and energy-free self-locking. The dual-ratchet structure assembled in an offset configuration significantly increased the angular resolution of the joint locking mechanism. Key experimental results demonstrated the gripper's superior performance: a remarkable maximum load capacity of 4200 g, far exceeding that of conventional soft grippers (45-210 g); more uniform force distribution across object sizes (1.75-35.29% difference ratio) compared to a rigid gripper (56.77-66.44%), with peak contact forces remaining below surface damage thresholds; and a 50.05% reduction in total energy consumption to 42.6 J per grasp cycle, achieved by eliminating the need for continuous pneumatic pressure through the self-locking mechanism, compared to 85.28 J for a conventional soft gripper. The combination of additive manufacturing for ratchets and commercially available materials for pneumatic chambers ensured a low-cost and easily fabricated design. These findings validated that the proposed gripper successfully bridged the gap between soft compliance and rigid reliability, offering a robust and efficient solution for scalable agricultural harvesting and manipulation tasks.

Soft metamaterials provide a promising platform for robotics, biomedical devices, and flexible electronics. The localized mechanical responses by nonuniform excitation are ubiquitous in soft materials, yet their controlled transmission across assemblies remains largely overlooked in metamaterial design, which critically constrains nontrivial functionalities with end-to-end and long-range deformation transmission. Here, we introduce an impedance-guided design framework that enables programmable transmission of localized deformation in modular soft metamaterials, achieving behaviors unattainable by intuitive design. By establishing a nonlinear model considering position-dependent interactions and integrating the concept of mechanical impedance within metamaterials, we regulate assembly-level transmission solely through unit-cell topology optimization. The resulting framework enables effective synthesis of module families, allowing both homogeneous and heterogeneous assemblies to be custom-built with markedly enhanced transmission characteristics. Leveraging the highly combinatorial and extensible design space, we physically realize diverse on-demand displacement manipulation architectures, including obstacle-bypassing modular soft-metamaterial assemblies, defect-tolerant soft gripping, and embodied signal processing. Beyond deformation programming, the reconfigurability and reassemblability of these soft modules can embed electric logic signals, enabling energy-efficient and low-latency information processing through compliant-switch-controlled mechanical LED displays and wearable finger-motion-sensing controllers. Our method provides fundamental insights into localized deformation transmission in modular soft metamaterials and establishes a scalable route toward embodied-intelligence material systems, particularly for soft-metamaterial-centric actuation, sensing, and collective computing.

Grasping in unstructured environments requires handling objects with widely different mechanical properties, from soft and deformable items to rigid everyday objects. Most existing approaches address these categories separately and often rely on tactile sensing, object-specific models, or specialized grippers. In this paper, we present a unified monocular vision-based grasping framework that targets both soft and rigid objects within a single control pipeline, using only RGB input and a position-controlled gripper. The proposed system combines open-vocabulary object detection, image segmentation, boundary-aware point assignment, real-time point tracking, and monocular depth estimation to recover object motion and geometry from visual observations. A key component of the framework is a language-based stiffness estimation model that infers an object's expected compliance from its semantic description and provides an object-level prior for selecting the grasping strategy before contact. For deformable objects, grasp adaptation is governed by a Procrustes-based dissimilarity measure computed from tracked keypoints, which acts as a visual proxy for deformation. For rigid objects, the gripper width is regulated through the scaling of tracked point distances. We validate the proposed method in real-world pick-and-place experiments on a Franka Emika Research 3 arm using objects with substantially different mechanical properties, including lettuce, fresh mozzarella cheese, croissants, paper towels, and hard plastic bottles. Results demonstrate that the framework achieves stable grasping across both soft and rigid objects using visual feedback alone, highlighting a practical, sensor-efficient, and generalizable approach for food handling and household manipulation.

Vision Language Action (VLA) models unify visual perception, natural-language understanding, and action generation within a single foundation model, allowing a robot to follow instructions such as fold the towel or fly to the red building directly from camera images. Because VLAs inherit world knowledge from internet-scale pre-training, they have become the dominant framework for learning-based manipulation, with bimanual coordination serving as the most demanding testbed: two arms with 7 degrees of freedom each must move in concert to fold, assemble, and reorient objects. Unmanned aerial robotics faces a structurally similar challenge: a drone must coordinate thrust, attitude, and increasingly gripper commands from visual observations under strict latency and payload constraints. This review covers 183 contributions spanning 2017-2026 and organized along seven dimensions: VLA architectures, training recipes, action representations, bimanual coordination (2022-2026), unmanned aerial vehicle (UAV) navigation and control (2017-2026), language grounding, and cross-cutting concerns including memory and world models. We show that the coordination strategies, training recipes, and action representations developed for bimanual VLAs transfer to unmanned aerial systems and identify fourteen research directions across both domains.

Most quadruped loco-manipulation designs trade manipulation capability against stance. A trunk-mounted arm sits high and usually carries a single arm; using the legs as manipulators lifts the manipulating leg off the ground; and even leg-mounted grippers reach two-handed tasks only by rearing onto the hind legs. This paper integrates a manipulator with a prismatic slider, two revolute joints, and a gripper into each front calf of a Unitree Go2. The two arms grasp objects at ground level and manipulate with both hands while all four feet stay planted, without rearing. With one arm carrying, the base stays free to walk. A vision-language model sequences skills from a predefined library at each skill boundary, conditioned on the head-camera image and task state, for long-horizon autonomy. In simulation, the design performs three bimanual tasks: a long-horizon cabinet task under autonomous skill selection, a cooperative two-handed lift, and an inter-arm handover.

Dexterous grasping across diverse object scales requires contact modes ranging from two-finger pinches to bimanual grasps. Existing dexterous grasp synthesis methods reduce the high-dimensional optimization space with manually designed expected contacts and initialization heuristics, which struggle to balance synthesis success rate and diversity. We present HUGS (Human-prior-guided Unified Dexterous Grasp Synthesis), a human-prior-guided framework for unified dexterous grasp synthesis across modes and scales. Instead of directly retargeting human demonstrations, HUGS learns an object-conditioned human prior that captures human grasp preferences and guides downstream force-closure-aware optimization. The prior is trained on a compact self-collected human grasp dataset with 1.8K grasps over 304 objects, providing broad coverage of object scales and contact modes. During synthesis, HUGS adaptively proposes contact modes and wrist initializations, substantially improving the balance between contact-mode coverage and synthesis success rate over heuristic-based methods. With HUGS, we synthesize 3.2M robotic grasps over 157K scenes, spanning object half-diagonal lengths from 2 cm to 30 cm and modes from two-finger to bimanual grasps. Models trained on the synthesized dataset autonomously select appropriate contact modes in the real world, enabling grasping from screws to large boxes.

Large-scale dexterous grasp datasets encode rich priors over hand-object interaction, but their use has largely been confined to grasp generation and pick-and-place manipulation. We study whether such data can instead support functional dexterity in articulated tool use, where a robot must acquire a tool, maintain contact, and operate its functional moving parts. We adapt a hierarchical imitation learning framework that combines high-level hand sub-goal prediction with a low-level goal-conditioned controller. We construct a 355k-trajectory grasp-pretraining dataset from large-scale dexterous grasp annotations and use it to pretrain the low-level controller. The controller is then fine-tuned on downstream task demonstrations. To evaluate this setting, we introduce DexCraft, a simulation benchmark with six articulated tool-use tasks requiring coordinated finger motion. Across simulation and real-world experiments, our approach outperforms end-to-end diffusion policy baselines and hierarchical policies trained from scratch. In the real world, it improves full-task success by 33.3 percentage points over DP3. These results show that grasp datasets can serve not only as resources for grasp synthesis, but also as scalable pretraining data for contact-rich dexterous manipulation. Videos are shown on https://yingyuan0414.github.io/grasp2dexterity/ .

High-quality demonstration data are essential for humanoid robot skill learning, especially for whole-body behaviors that require coordinated perception, locomotion, and manipulation. Existing data-collection methods largely rely on robot teleoperation, which is constrained by hardware accessibility, operator expertise, and limited efficiency. Inspired by the Universal Manipulation Interface (UMI), we propose HumanoidUMI, a portable and robot-free framework for humanoid whole-body data collection. HumanoidUMI uses lightweight VR devices and UMI-inspired grippers to collect sparse human keypoint trajectories, wrist-view observations, and gripper actions. These demonstrations train a high-level policy to predict future keypoints, which are retargeted to robot-native whole-body references and executed by a whole-body controller. Experiments in five real-world scenarios demonstrate the effectiveness of the proposed framework and validate the collected demonstrations for transferable humanoid whole-body skill learning.

Vision-Language-Action (VLA) models have shown strong potential for generalizable robotic manipulation. During fine-tuning, however, action supervision applies equally across all timesteps, without structured supervision on which manipulation stage the robot is in or what the next gripper-event target should be. This causes failures to concentrate around challenging gripper-event transitions. To address this, we propose StaKe, a plug-in auxiliary supervision framework that automatically derives two complementary signals from demonstration gripper states without manual annotation: a stage classifier that identifies the current manipulation stage, and a keyframe predictor that estimates the target joint action at the next gripper transition. Both are modeled as lightweight auxiliary heads that enrich the learned representations during training, while leaving the base VLA policy architecture and inference loop unchanged. Experiments on bimanual simulation and single-arm Franka real-robot tasks show that StaKe consistently improves success rates (relative gains of 14% and 56%, respectively), with larger improvements on longer-horizon tasks that involve more gripper-event transitions. Ablation studies validate each design choice, and qualitative analysis confirms that the learned representations faithfully track manipulation stages. These results indicate that structured supervision is an effective and general strategy for enhancing VLA fine-tuning in long-horizon manipulation. Project website: https://hi-yuanxu.github.io/StaKe-Web/

We present Cloak, a training recipe that endows a Vision-Language-Action (VLA) model with zero-shot cross-embodiment transfer by cloaking the end-effector from its own wrist camera. The end-effector occupies a large and consistent region of the wrist view and masking it allows for embodiment-agnostic visual reasoning. Cloak renders a mask in simulation from the robot's known geometry, accurately and in real time, with no segmentation or generative models. During training, we augment the mask so the model generalizes to embodiments unseen at training time. We demonstrate the recipe with Cloak-VLA, a VLA trained with Cloak on a single parallel-jaw gripper dataset. No data of new embodiments is ever collected. Cloak-VLA transfers zero-shot to various unseen embodiments, including another gripper, another arm, and a five-fingered hand, while preserving the source embodiment's performance. By decoupling the wrist view from its own embodiment, Cloak allows data to outlive the hardware it was collected on.

The Manipulider is a buoyancy-actuated underwater robot that enables thrusterless, glide-like locomotion and attitude-based manipulation, while providing a magnetic modular interface for rapid payload swapping (e.g., a gripper or sensors). Four syringe-based buoyancy engines distributed around the body jointly regulate net buoyancy and the center of buoyancy, allowing the vehicle to maintain large tilt angles through static force balance without continuous thrust and to avoid propeller entanglement risks. We present the mechanical and electrical design, calibration procedure, and control architecture. Experiments with a gripper attached (no external payload) show a controllable buoyancy-displacement range of 40 mL per engine ({\approx}160 g total buoyancy authority), maximum statically stable tilts of 64.6° (single-engine) and 61.8° (dual-engine), and representative vertical and tilt-transition dynamics. We further demonstrate tilt regulation, controlled ascent/descent primitives, and a proof-of-concept gripper-based payload-transport sequence without thrusters.

Parallel-jaw grippers are the default manipulator choice in robotics because they are simple, robust, and inexpensive. Their limited in-hand mobility, however, often forces large arm motions and restricts dexterous manipulation in confined workspaces. We present a parallel-gripper upgrade: a double-soft-belt-based finger module that preserves standard opening/closing while adding three in-hand degrees of freedom (DoF): translation, pitch, and roll. The mechanism is deliberately kept simple and engineered for inexpensive manufacturing and straightforward integration, preserving the reliability and precise control of traditional parallel grippers while greatly broadening the range of manipulation capabilities. To demonstrate the utility of the added DoFs, we integrate the gripper in two control pipelines. First, we adapt a model predictive controller for in-hand manipulation of known objects. Second, we introduce a lightweight teleoperation interface that enables simultaneous control of the robot arm and gripper (10 DoFs total) with minimal hardware. Across a suite of challenging manipulation tasks executed via teleoperation, MPC, and trained policies, the proposed gripper consistently improves dexterity and task feasibility compared to a conventional parallel gripper

We introduce Yielding Universal Bidigital Interface (YUBI), a finger-aligned gripper designed to enable intuitive, ergonomic, and scalable data collection for bimanual dexterous manipulation. While handheld data collection systems such as Universal Manipulation Interface (UMI) enable affordable data collection, their bulky pistol-grip designs can pose ergonomic and usability challenges for fine-grained, dexterous manipulation tasks. To address this, YUBI presents a distinct design principle: yielding, finger-driven actuation that directly maps human finger movements to gripper jaw motion. Using the YUBI devices, we set up a data collection system with integrated VR-based 6 DoF tracking of the gripper, ensuring high-fidelity trajectory data acquisition. We curate a UMI-based dataset of unprecedented scale: 8,434 hours across 1.20M episodes and 119 tasks. Experiments show that YUBI offers advantages over the UMI gripper in versatility for complex bimanual tasks, dexterity, and operational efficiency. A single policy trained on the YUBI dataset transfers across multiple bimanual robots (UR, Franka, and ELEY) simply by mounting the gripper on each platform, confirming that the collected data are directly executable as policy supervision. We release the gripper hardware, data-collection software, and dataset as one integrated stack, offering the open community a reproducible path to large-scale data acquisition for advancing robotic foundation models.

We study whether demonstration-curation metrics that detect defective training episodes also improve the downstream behavior-cloning policy that trains on the curated data. On a contact-rich LIBERO pick-and-place benchmark with a controlled structural defect (early gripper release during the carry phase), we find that the two quantities are sharply decoupled. The metric with the highest defect-detection AUROC (0.804) produces the worst curated policy (13.3% task success), while a metric with a substantially lower AUROC (0.638) produces a policy that nearly matches the oracle trained on ground-truth clean data (90.0% vs. 93.3%). We further show that five of the seven metrics we evaluate exploit episode length as a trivial proxy for the defect label, a confound that inflates reported AUROCs to near-perfect values and disappears once episode length is controlled. Across all conditions, the contaminated baseline succeeds on only 3.3% of rollouts, and the two best curation methods close this to within 3 percentage points of the 93.3% oracle ceiling. Our results argue that curation methods should be evaluated by the policy they produce, not the defects they flag, and that any curation benchmark must control for episode length before reporting detection accuracy. We release the testbed, all metric implementations, and the evaluation pipeline.

Force and tactile sensing are indispensable in contact-rich manipulation. However, force-aware robot learning faces critical challenges due to the incompatible assembly of tactile and force sensors in handheld or wearable devices. To address these limitations, we first introduce AetheRock for gripper-force, vision, and tactile data collection, which is an arm-worn device featuring a modular and easily manufactured visuo-tactile sensor, GelSlim-MiniFab, at the fingertip, a resistive pressure sensor at the human finger contact region, a customized PCB module, and a wearable kit for comfortable and robust collection. Building on this, we propose ForceVT, a representation learning framework that uses force and vision to guide fidelity-agnostic tactile learning, enabling robust inference in any tactile situation. Real-world experiments show that AetheRock achieves qualified data efficiency and that ForceVT effectively alleviates inefficiencies when visuo-tactile sensors exhibit manufacturing and utilization inconsistencies. Overall, our work mitigates the limitations of gripper-force vision-tactile robot learning through innovative hardware design and algorithms.

Fin Ray-inspired soft grippers offer a promising solution for gently handling delicate, irregular objects, especially in agriculture. The objective of this research is to design, fabricate, and model a Fin Ray Effect (FRE) soft gripper finger to enable precise force control in future applications. This design aims to gently grasp delicate agricultural products, such as tomatoes, that require both adaptability and accurate force application. To address the inherent challenges of soft robotics, including nonlinear behavior, infinite degrees of freedom, and variable material properties, the Finite Rigid Elements Method (FREM) was employed for modeling. This method preserves analytical accuracy while providing a reliable foundation for the development of a force controller in later stages. A detailed Finite Element Model (FEM) was created using ANSYS, and the analytical results were validated through simulation and experimental testing. The gripper's fingers were optimized based on four key criteria: tip displacement, total deflection, stress distribution, and contact force. The optimal finger configuration includes a length of 30 mm, rib spacing of 10 mm, seven ribs angled at -15 deg, and a rib thickness of 1 mm. Theoretical modeling using the FREM predicted finger deformation with a 3% error, while the ANSYS numerical model achieved 2% error.

Underwater manipulation often occurs under degraded visibility due to turbidity, glare, and gripper occlusion, limiting the reliability of vision-based perception during approach and grasping. In such settings, soft grippers are well suited for compliant interaction, but they typically lack an onboard pre-contact cue that can guide approach and closure when vision is unreliable. This extended abstract explores active electrosense as a lightweight sensing modality that can provide a proximity-like signal prior to contact by measuring perturbations of an applied electric field in conductive media. We instrument an octopus-inspired gripper with a discrete electrode layout and record multi-channel sensing voltages using off-the-shelf hardware. Simulation and tank experiments with a suspended conductive sphere show structured, object-dependent changes in the multi-electrode voltage readout relative to empty-water baselines, with detectability varying across excitation of 5 to 20 V and frequencies from 1 mHz to 1 kHz. These findings motivate systematic investigation of gripper-integrated electrosense as a complementary pre-contact cue for underwater soft manipulation.

A passive monolithic compliant grasping mechanism that works based on the eversion of an elastically deformable bistable shell is conceptualized. It comprises grasping arms made of beam segments that work in conjunction with the everting shell. The grasper is capable of picking up a stiff object of any shape up to a maximum size and weight. The bistable shell everts upon contact with the object to enable the grasping arms envelop the object forming an enclosure. The mechanism then stays in that configuration until it is actuated again to turn the shell back to its original configuration and thereby opening the enclosure to release the object. The stiffness of the arms decides the payload of the mechanism. The size of the arms decides the largest object that can be grasped and held. The arms have distributed compliance so that they can conform to the shape of the object without applying undue force on it.

Soft wearable robotic systems have emerged as a promising solution for assisting individuals with reduced hand function. This paper presents SoFiE, a modular soft finger exoskeleton designed to assist index-finger flexion during grasping tasks. The proposed system is primarily fabricated using 3D-printed flexible materials, enabling a lightweight, low-profile, and modular design. Actuation is achieved through a tendon-driven mechanism powered by a compact DC motor, while passive extension is provided by a compliant conductive spring. This element, termed StretchSense, also functions as a proprioceptive sensor by exhibiting resistance changes under deformation. Furthermore, a novel tactile sensing approach, MagSense, is introduced, using a magnet and magnetometer pair embedded in a soft fingertip structure to estimate contact force and object compliance. The system is fully untethered and controlled by an embedded microcontroller. In addition, actuator-level sensing through motor encoder feedback enables estimation of the system state, providing a foundation for safe and adaptive control strategies. Experimental validation demonstrates the capability of the system to provide reliable pose estimation, distinguish between materials with different stiffness, and generate distinct sensor signatures across different grasping tasks. This paper details the design, fabrication, and sensing concepts of the proposed exoskeleton as a proof of concept toward modular, soft, and assistive wearable robotics.

Increasing interest in deep-sea operations and resources motivates the development of ecologically sensitive but environmentally durable robots. Dielectric elastomer actuator artificial muscles are good candidates for powering such systems due to their pressure and temperature tolerance and soft makeup, but they are difficult to integrate with robotic systems. This work presents an autonomous robotic platform: the CORE, capable of driving six artificial muscles while sensing visual and spatial information. To validate the platform, we developed the Cuttlebot - a cuttlefish-inspired robot that swims in three dimensions using undulatory fin locomotion. The Cuttlebot has four primary artificial muscles in its fins in addition to a tentacle-inspired soft gripper. The robot was evaluated in a series of tethered and untethered swimming tests, demonstrating a top speed of 2.5 centimeters per second translation and 10 degrees per second rotation. Furthermore, the CORE system was capable of driving specialized control signals into the artificial muscles to controllably output force and torque in six axes. This work provides a platform for developing complex, bio-inspired swimming robots for ocean exploration and monitoring, laying the foundation with our leading example: the Cuttlebot.

In this paper, we use asymmetric vibrations to demonstrate two degree-of-freedom (DoF) in-hand manipulation of grasped parts. The asymmetric vibrations are achieved through closed-loop position control of a moving surface, which applies a periodic stick-slip waveform to the part to be manipulated. We show analytically how two vibratory waveform parameters, the sticking acceleration and the slipping acceleration, affect average part velocity when moving against gravity. The theoretical trends are then validated using an experimental setup where the squeeze force is controlled and part motion is recorded by a high-resolution encoder. We also develop a 2-DoF vibratory surface capable of translation in one direction and rotation about the surface normal. Using two of these 2-DoF surfaces in a parallel jaw gripper configuration, we bidirectionally translate and rotate a variety of grasped parts, as well as demonstrate that the same waveform trends for translation also persist for in-plane rotation.

Robotic in-hand manipulation requires reliable object-motion tracking under frequent visual occlusion, yet low-texture visuotactile images provide few stable correspondences for conventional image- or geometry-matching methods. This paper presents TacSE3, a tactile motion-estimation pipeline that converts low-texture visuotactile observations into a decoupled three-dimensional force field and estimates incremental rigid-body motion on SE(3). The method derives planar translation from contact-centroid motion and estimates rotation primarily from shear-related tactile responses, yielding a physically interpretable signal for in-gripper tracking and compensation. Experiments with paired DM-Tac fingertip sensors show that dual-sensor sensing reduces translation-rotation ambiguity, supports rotation tracking across axes and object geometries, and provides a lightweight compensation signal that improves disturbance tolerance in downstream manipulation tasks without retraining the base policy.

Astrobee's existing one-degree-of-freedom (DOF) underactuated compliant claw gripper enables perching on the International Space Station (ISS), but provides limited capability for continuous dexterous manipulation. More complex microgravity tasks require an end-effector that can maintain stable contact while limiting disturbance to the free-flying base, since contact forces directly couple into base motion. This article presents the integration of DexCoHand, a dexterous and compliant two-finger, 6-DOF gripper, with the Astrobee free-flying robot for microgravity manipulation. The system is evaluated in MuJoCo using Astrobee's standard handrail perching sequence, including approach, perching, and subsequent pan and tilt motions. Compared with Astrobee's existing gripper, DexCoHand preserves the commanded pan and tilt motions while reducing unintended cross-axis base motion. Hardware experiments on Earth further demonstrate DexCoHand's dexterous manipulation capabilities and its potential for more adaptable intelligent manipulation tasks.

Rearranging densely packed tabletop objects is challenging when parallel-gripper picks are infeasible without sufficient clearance around an object. This work studies the problem characteristics for practically motivated settings with uniformly sized blocks placed at planar tabletop grid locations. Since purely prehensile removal can become infeasible, a directional knock primitive is therefore introduced and the optimal knock-pick variant of the problem is formulated. The work proposes a series of abstractions wherein minimal constraining gadgets are covered to identify the necessary knocks. Utilizing a maximum-weight perfect matching on a graphical abstraction yields efficient polynomial-time computation of the optimal plan that minimizes the number of actions. Experiments are reported for increasing grid sizes in synthetic settings as well as in IsaacSim. The theoretical observations provide a promising stepping stone towards rigorously building efficient manipulation strategies that interleave prehensile and non-prehensile actions.

Achieving human-level manipulation requires dexterous robotic hands capable of complex object interactions. Advancing such capabilities further demands standardized benchmarks for systematic evaluation. However, prior work does not focus on task-oriented dexterous manipulation. Existing benchmarks also often lack high quality human demonstrations and an easy-to-use evaluation pipeline. In this paper, we present DexJoCo, a benchmark and toolkit for task-oriented dexterous manipulation, comprising 11 functionally grounded tasks that evaluate tool-use, bimanual coordination, long-horizon execution, and reasoning. We develop a low-cost data collection system and collect 1.1K trajectories across these tasks, with support for domain randomization to assess robustness. We benchmark modern models under diverse settings, including visual and dynamics randomization, multi-task training, and action-head adaptation. Through extensive empirical analysis, we identify several important insights and common limitations of current policies in dexterous manipulation, highlighting key challenges for future research in dexterous hand robot learning. Code is available at: https://dexjoco.github.io

Robotic manipulation of flexible objects is widely required in both industrial and service applications. Among such objects, paper-like materials exhibit distinct mechanical characteristics compared to cloth, being more sensitive to compressive stress, where minor variations in physical properties can significantly affect grasping. This study systematically investigates grasping strategies for paper-like materials using a universal soft gripper by exploiting environmental constraints. Based on manipulation primitives employed in existing grasping strategies, we proposed systematic grasping strategies for flexible materials by exploiting environmental constraints and analyzed their mechanical and kinematic models. To investigate the influence of materials and working conditions on grasping, an evaluation system for measuring grasping force and success rate was defined and experimentally evaluated. Finally, we summarized the specific workspaces and characteristics of different strategies that can satisfy various task requirements and lead to potential applications in household service robots for grasping planar flexible objects.

Assistive robotic grasping plays an important role in enabling safe and adaptive manipulation of diverse objects. However, existing systems often rely on electronic sensing and multi-stage processing pipelines, increasing system complexity and reducing accessibility. To address these limitations, we present TouchDrive, a cost-effective, electronics-free tactile sensing interface for assistive grasping. TouchDrive directly converts contact forces into pneumatic feedback through valve-mediated switching, integrating sensing, signal generation, and feedback within a single passive mechanical loop. The system can be employed using a pneumatic normally closed valve, a compressed air tank, sensing element, and haptic feedback actuator without electronics. By delivering tactile cues, TouchDrive empowers users to modulate grasp forces, enabling precise and robust delicate manipulation of compliant and fragile objects. The interface has been validated across diverse robotic platforms, consistently demonstrating reliable performance and practical applicability in assistive grasping tasks, such as handling fruits and everyday items (up to 20 objects).

We introduce an elastic-driven self-folding approach that fabricates robots directly from flat 3D-printed conductive PLA nets. Elastic bands routed through printed hooks store energy that folds the sheet into programmed 3D geometries, while the flat state allows accurate placement of electronics and magnets before deployment. The same substrate doubles as electrodes for capacitive touch and supports a reusable platform I/O palette with Hall sensors and eccentric rotating mass (ERM) motors for docking detection and vibration actuation. We also derive a closed-form folding model that balances hinge stiffness with elastic band moment to predict equilibrium fold angles; experiments validate the model and yield a design map linking hinge thickness, band size, and hook spacing to target angles. Using this workflow we realize multiple polyhedral modules and demonstrate three applications: a cube that highlights the potential of self-folding for scalable modular robot collectives, a deployable gripper, and a tendon-driven finger. The method is low cost, stimulus-free, and integrates actuation and sensing.

High-quality demonstration data are essential for humanoid robot skill learning, especially for whole-body behaviors that require coordinated perception, locomotion, and manipulation. Existing data-collection methods largely rely on robot teleoperation, which is constrained by hardware accessibility, operator expertise, and limited efficiency. Inspired by the Universal Manipulation Interface (UMI), we propose BifrostUMI, a portable and robot-free framework for humanoid whole-body data collection. BifrostUMI uses lightweight VR devices and UMI-inspired grippers to collect sparse human keypoint trajectories, wrist-view observations, and gripper actions. These demonstrations train a high-level policy to predict future keypoints, which are retargeted to robot-native whole-body references and executed by a whole-body controller. Experiments in five real-world scenarios demonstrate the effectiveness of the proposed framework and validate the collected demonstrations for transferable humanoid whole-body skill learning.

Humans grasp unfamiliar objects by combining an initial visual estimate with tactile and proprioceptive feedback during interaction. We present ShapeGrasp, a robotic implementation of this approach. The proposed method is an iterative grasp-and-complete pipeline that couples implicit surface visuo-haptic shape completion (creation of full 3D shape from partial information) with physics-based grasp planning. From a single RGB-D view, ShapeGrasp infers a complete shape (point cloud or triangular mesh), generates candidate grasps via rigid-body simulation, and executes the best feasible grasp. Each grasp attempt yields additional geometric constraints -- tactile surface contacts and space occupied by the gripper body -- which are fused to update the object shape. Failures trigger pose re-estimation and regrasping using the refined shape. We evaluate ShapeGrasp in the real world using two different robots and grippers. To the best of our knowledge, this is the first approach that updates shape representations following a real-world grasp. We achieved superior results over baselines for both grippers (grasp success rate of 84% with a three-finger gripper and 91% with a two-finger gripper), while improving the 3D shape reconstruction quality in all evaluation metrics used.

Grasp force estimation can help prevent robots from damaging delicate objects during manipulation and improve learning-based robotic control. Integrating force sensing into deformable grippers negotiates trade-offs in cost, complexity, mechanical robustness, and performance. With the growing integration of RGB-D wrist cameras into robotic systems for control purposes, camera-based techniques are a promising solution for indirect visual force estimation. Current approaches mostly utilize end-to-end deep learning, which can be brittle when generalizing to new scenarios, while existing model-based approaches are unsuited to grasping and modern grasper geometries. To address these challenges, we developed a model-based visual force sensing approach integrating an iterative contact localization with generalization to unseen objects. The system extracts structural key points from wrist camera RGB-D images of deforming fin-ray-shaped soft grippers, and uses these key points to define parameters of an inverse finite element analysis simulation in Simulation Open Framework Architecture. The iterative contact localization sub-system utilizes a deep learning-based online 3D reconstruction and pose estimation pipeline to dynamically update contact location, and is robust to visual occlusion and unseen objects. Our system demonstrated an average root mean square error of 0.23 N and normalized root mean square deviation of 2.11% during the load phase, and 0.48 N and 4.34% over the entire grasping process when interacting with different objects under various conditions, showcasing its potential for real-time model-based indirect force sensing of soft grippers.

Origami-inspired robotic grippers have shown promising potential for object manipulation tasks due to their compact volume and mechanical flexibility. However, robust capture of objects with random shapes in dynamic working environments often comes at the cost of additional actuation channels and control complexity. Here, we introduce a tendon-driven origami tentacle gripper capable of universal object gripping by exploiting a synergy between local, deterministic deformation programming and global, stochastic entanglements. Each origami tentacle is made by cutting thin Mylar sheets; It features carefully placed holes for routing an actuation tendon, origami creases for controlling the deformation, and a tapered shape. By tailoring these design features, one can prescribe the shrinking, bending, and twisting deformation, eventually creating deterministic coiling with a simple tendon pull. Then, when multiple coiling tentacles are placed in proximity, stochastic entanglement emerges, allowing the tentacles to braid, knot, and grip objects with random shapes. We derived a simulation model by integrating origami mechanics with Cosserat rods to correlate origami design, tendon deformation, and their collective gripping performance. Then, we experimentally tested how these coiling and entangling origami tentacles can grasp objects under gravity and in water. A stow-and-release deployment mechanism was also tested to simulate in-orbit grasping. Overall, the entertaining origami tentacle gripper presents a new strategy for robust object grasping with simple design and actuation.

In this paper, we introduce GET-2D-1.0, a fast grasp planner for the GET asymmetrical gripper that operates from a single-view RGB-D image, using the Ferrari-Canny metric and a novel sampling strategy, and GET-3D-1.0, a mesh-based method using a 3D gripper model and ray-tracing. We evaluate both grasp planners against baselines with physical experiments, which suggest that GET-2D-1.0 can improve over a bounding box baseline by over 40% in lift success, shake survival, and force resistance. Experiments with GET-3D-1.0 suggest slight improvement compared to GET-2D-1.0 on lift success and shake survival, but are more computationally expensive, averaging 17 seconds of planning compared to 683 ms for GET-2D-1.0.

Robotic fruit harvesting often fails to reliably detect whether a fruit has been successfully picked, limiting efficiency and increasing crop damage. This problem is difficult due to compliant fruit and grippers, variable stem attachment, and occlusions in orchard environments. Prior work has explored vision-based perception and multi-sensor learning approaches for pick state estimation. However, minimal sensor sets and phase-dependent sensing strategies for accurate pick and slip detection remain largely unexplored. In this work, we design and evaluate a multimodal sensing suite integrated into a compliant suction-based apple gripper. Our approach is unique because it identifies which sensors are most informative at different phases of the pick, enabling predictive detection of failures before they occur. The contributions of this paper are a phase-dependent evaluation of multimodal sensors and the identification of minimal sensor sets for reliable pick state classification. Experiments in a real apple orchard show that Random Forest and Multilayer Perceptron classifiers detect successful picks and impending failures with over 90% accuracy, and Random Forest predicts pick/slip events within 0.09 s of human-annotated ground truth.

We present HRDexDB, a paired cross-embodiment dexterous grasping dataset of high-fidelity dexterous grasping sequences featuring both human and diverse robotic hands. Unlike existing datasets, HRDexDB provides a comprehensive collection of grasping trajectories across human hands and multiple robot hand embodiments, spanning 100 diverse objects. Leveraging state-of-the-art vision methods and a dedicated multi-camera system, HRDexDB offers high-precision spatiotemporal 3D ground-truth motion for both the agent and the manipulated object. The dataset comprises 2.1K grasping trials, each enriched with synchronized visual and kinematic modalities, with contact-force signals available for tactile-enabled robotic hands. By providing closely aligned captures of human dexterity and robotic execution on the same target objects under comparable grasping motions, HRDexDB serves as a foundational benchmark for cross-embodiment dexterous manipulation.

Offshore inspection and maintenance have increasingly been using legged robots for routine sensing, yet many useful interventions still require physical interaction with tools, containers, and task-relevant objects. Employing robots for these tasks can reduce operators' exposure in confined, elevated, or potentially explosive areas. This paper presents a language-guided grasping pipeline for a legged mobile manipulator operating under partial observation. An operator defines the target, the system grounds it in RGB with open-vocabulary detection and promptable segmentation, extracts an object-centric RGB-D point cloud, improves sparse geometry through depth compensation and point-cloud completion, and selects a 6-DoF grasp using collision, clearance, reachability, and approach constraints. The system is implemented on a quadruped robot with an arm and evaluated in two cluttered tabletop scenes motivated by small-object retrieval during inspection and maintenance. Across paired trials, the proposed pipeline achieved 9/10 successful grasps, compared with 3/10 for a view-dependent deployment baseline. In this controlled setting, object-centric completion and execution-aware selection reduced approach collisions and improved the reliability of language-guided grasping for supervised field manipulation.

Tactile feedback is important for contact-rich robotic manipulation, yet effective use of tactile observations remains challenging when tactile signals are image-like, hardware-dependent, and only weakly aligned with external visual observations. This study addresses this representation-learning problem by proposing a visuo-tactile contrastive learning framework for imitation-based manipulation. The method aligns external RGB observations and calibrated tactile images in a shared embedding space using a CLIP-style objective, and integrates the resulting representation into an Action Chunking Transformer (ACT) policy. A low-cost visuo-tactile gripper (LVTG) is proposed to provide a modular and durable sensing platform for reproducible data collection, supplying tactile observations that can be used by downstream manipulation algorithms. Experiments on contact-rich manipulation tasks show that tactile feedback improves the average task completion rate from 30% for a vision-only ACT baseline to 42%, and that the proposed contrastive pretraining further increases the completion rate to 54%. These results indicate that explicitly aligning visual and tactile observations provides more useful contact-aware features for downstream policy learning than directly adding tactile images without pretraining.

Typically, heuristic/trial-based approaches are used to design soft pneumatic grippers (SPGs). This paper presents a systematic topology optimization framework for developing SPGs. The design-dependent nature of actuating load is modeled using Darcy's law with an added drainage term. A 2D soft arm unit is then optimized as a compliant mechanism under pneumatic loading. To ensure the design is robust and manufacturable, the problem is formulated as a min-max optimization, where output deformations of blueprint and eroded designs are considered. A volume constraint is imposed on the blueprint part, while a strain-energy constraint is enforced on the eroded part. The Method of Moving Asymptotes is employed to solve optimization problems. The optimized 2D part is extruded suitably to generate a 3D unit. Ten such 3D units are assembled to create a gripper arm. Both the optimized 2D unit and the corresponding gripper arm outperform their conventional rectangular designs under pneumatic loading, demonstrating the efficacy of the proposed approach. The arms are fabricated using the SLA printing technique. Numerical and experimental results are compared at different pneumatic loads. Four 3D-printed arms are integrated with a supporting structure to form the SPG. The gripping action of the SPG is demonstrated on objects with different weights, sizes, structures, stiffnesses, and shapes.

Natural-language manipulation instructions specify the task goal but leave the underlying robot trajectory unspecified. We present AntiGrounding, a visual action-selection framework built around a dual geometric-visual trajectory interface. After feasibility filtering, each retained short trajectory is both an explicit motion plan for execution and a rendered prompt for instruction-conditioned vision-language model (VLM) evaluation. Structured multi-view visual question answering (VQA) scores safety, task alignment, efficiency, and physical plausibility; weighted view fusion aggregates the trajectory scores. These scores guide subsequent translational trajectory proposals; separate orientation and gripper controls coordinate interaction. An initialized digital twin provides the planning state and validates selected segments before the real robot executes the same waypoint sequences. Across eight real-world manipulation tasks, AntiGrounding with a single GPT-6 Astra evaluator achieves 71.25% overall success, compared with 50.00% for pi0.5 and 47.50% for a PIVOT-style visual proposal-selection baseline using the same evaluator under the reported deployment protocol. Component ablations and evaluator-sensitivity analyses examine trajectory evaluation, proposal search, orientation control, and evaluator choice. The interface connects general-purpose multimodal reasoning to executable trajectories, with performance bounded by digital-twin fidelity and physical interaction.