Continuum Robots

Continuum robots enable smooth shape morphing and safe interaction in confined environments. However, most existing systems are task-specific and depend on external sensing infrastructure, limiting their adaptability and real-world deployment. This paper presents a self-contained modular continuum robotic platform that combines mechanical reconfigurability with onboard pose estimation. The robot is constructed from interchangeable continuum joints with analytically precomputed stiffness, allowing rapid assembly and direct programming of the robot shape. Proprioceptive sensing is achieved using magnetic sensors and a modular learning-based framework, where a single model is trained per joint and reused across configurations. The system is experimentally validated in real world, demonstrating self-sensing capabilities and adaptation without external tracking.

Animals coordinate their movements through distributed neural circuits, but soft robots still typically depend on external, centralized electronics for control. Building soft robots that operate without centralized electronic controllers while remaining responsive to their environment remains a frontier challenge in soft robotics. In this work we introduce a soft-robot control architecture inspired by leaky integrate-and-fire models of biological neural circuits. The Pneumatic neuron (Pneu-ron) is a soft actuator that unifies energy conversion, logic, and actuation in one component. Each module combines a low-boiling-point fluid (LBF), a heater, and a mechanical switch into a self-excitable unit. Boiling the LBF inflates the module and triggers excitation and inhibition of adjacent modules in a process we call "inflate-and-fire". When interconnected into excitatory-inhibitory rings, Pneu-rons generate stable, sequential oscillations whose frequency emerges from the material dynamics and environmental conditions. By harnessing the inflation of Pneu-rons for actuation these networks can drive oscillatory locomotion of soft robots. Pneu-ron networks sustain oscillation under mechanical load and thermal variations, adapting through material physics rather than computation. Dynamical modeling of these networks reveals a dimensionless bifurcation diagram that dictates the network's oscillatory behavior. Encoding logic and actuation into material-level modules presents a new avenue for adaptive, electronics controller-free, soft robots.

We present the PccDiffuser, a conditional diffusion framework for continuum robots that learns a multimodal distribution over complete configuration-space paths and samples multiple candidate solutions in parallel, which are subsequently converted into an executable trajectory by time allocation considering actuator constraints. Under the piecewise constant-curvature model, we use exponential co-ordinates to describe the robot kinematics, and use graph neural network to encode a variable number of environment obstacles. Analytical differential kinematics is incorporated in the denoising process to improve terminal accuracy and whole-body clearance. On a mixed test set comprising workspace with zero to four obstacles, PccDiffuser achieved a success rate of 91%. Compared with existing sampling- and optimisation-based benchmarks, it delivered both a higher success rate and greater computational efficiency, with the latter advantage becoming more substantial when sampling more candidate solutions. Experiments on a three-section tendon-driven continuum robot further demonstrate consecutive planning, multi-solution planning, and whole-body obstacle avoidance.

This paper presents a soft robotic drummer for accurate and efficient drum rolls. High-frequency drum rolls require the "multi-bounce technique," where a drumstick bounces multiple times with a single stroke. In robotic reproduction of this technique, the body's elasticity is key, while the fine motion during the stroke is also crucial for maximizing the potential of that elasticity. Therefore, we design two tricks: i) Tap-Pull (TP) trick to increase the number of rebounds by adding a pulling motion after impact; and ii) Micro-Pulse (MP) trick to keep the drumming volume by injecting small oscillations during the stroke. Due to the nonlinear complexity of soft embodiment, both tricks are efficiently tuned using Bayesian optimization in a data-driven manner for accomplishing the respective objectives quantified. We evaluated the optimized behaviors with soft and rigid end-effectors. As a result, the soft TP achieved the highest bounce count (12.25 per stroke) with uniform intervals. The soft MP suppressed the volume decay, yielding 6.8-times higher acoustic efficiency compared to the rigid MP. These results indicate that the proposed tricks with the combination of elasticity and optimization can make robots play excellent drum rolls.

Large language models (LLMs) have recently emerged as a promising tool for automating robot design from high-level specifications, yet they remain ineffective for robots operating under complex physical interactions. This limitation stems from the gap between language-based reasoning and the physical consequences of embodiment, often resulting in designs with low physical validity. In this work, we propose a multi-layered framework, AID-SR, that establishes a closed loop by translating simulator-observed physical states into structured feedback for the LLM designer. Combined with semantic critique, human feedback, and iterative refinement, the framework promotes the generation of physically feasible and functionally meaningful robot designs. We evaluate our approach on tendon-driven continuum robots across a benchmark of 14 tasks spanning reaching, grasping, locomotion, and manipulation. The proposed framework achieves 96.2% rate for passing the simulation feasibility check and by applying a common reinforcement learning training, 26.7% robots can successfully fulfill the corresponding task. We then fabricate three designed robots of AID-SR that successfully complete the task in real-world. These extensive experiments across simulation and real-world environments demonstrate and break the wall of utilizing the LLMs for automated design of continuum robots. The source code and experimental resources are publicly available at https://github.com/UNITES-Lab/AID-SR.

Soft eversion robots, also known as vine robots, have attracted growing interest for navigation and inspection tasks, including minimally invasive medical applications [1]. A vine robot consists of a thin, flexible, inextensible tube folded inward that everts and grows forward when pressurized. This tip-growth enables navigation with minimal friction, making vine robots well suited for complex environments such as the human colon [2]. While their inherent softness allows passive conforma- tion to curved pathways in confined spaces, navigation performance strongly depends on environmental inter- actions, including contact angle and the length of un- constrained deployed material [3], [4]. Sharp directional changes, such as those in the sigmoid colon, often limit passive growth and necessitate active steering. Existing solutions include distributed artificial muscles [5] or dedicated tip-based steering mechanisms [6]. In addition, many applications require payload delivery, such as sensors and tools [7], [8]. Within the ERC Synergy project EndoTheranostics, this motivates the development of vine robots capable of delivering micro- surgical tools during growth. Prior work has integrated working channels within the vine body [8], [9], but these approaches constrain tool size, introduce friction, and limit access to the environment to the robot tip. In this work, we propose a multi-vine architecture in which two vine robots are coupled to an externally integrated working channel via soft mounting tips [10]. Independent vine actuation enables active tip steering while advancing the working channel without embed- ding it within the vine bodies Figure 1. Experiments demonstrate sharp steering of nearly 90 degrees during growth, highlighting the potential of this architecture for versatile medical and non-medical applications.

Multi-segment soft robotic arms can continuously reconfigure their body shapes for safe interaction, but tip control alone is insufficient for constrained-space tasks. Therefore, shape control is a more important task for multi-segment soft arms than tip control, but remains challenging due to the high dimensionality and nonlinear dynamics of continuum deformation. In existing work, shape control accuracy is defined by the error in the global frame (global shape error). For multi-segment soft arms, using only global shape error as the control objective is insufficient, as segment coupling, gravity-induced loading, and inertial effects become more significant. This difficulty increases with the number of segments. In this paper, we present a Koopman-based model predictive control framework that combines global and local observables, enabling real-time shape control on multi-segment soft robotic arms. The framework is evaluated through numerical and physical experiments. Numerical experiments demonstrate the scalability of the proposed controller by achieving shape control on robots with up to 10 independently actuated segments. The physical experiments demonstrate that the controller is capable of (1) real-time shape control of 3- and 5-segment robotic arms with tip speeds up to 0.6 m/s, (2) robust tracking without retraining, including distal payloads up to 400g and recovery from a 7N lateral disturbance, and (3) the potential for future inspection applications through a confined-space demonstration. These results demonstrate that the proposed framework enables dynamic, scalable, and accurate real-time shape control on multi-segment soft robotic arms.

Conventional soft robot actuators excel in compliance, but their uncontrolled deformations compromise accuracy and hinder scaling to multi-degree-of-freedom (DoF) systems. We introduce a MONOlithic ORIGAMI-inspired soft folding actuator design (MONORIGAMI) that establishes a design strategy based on spatially programmed stiffness anisotropy to preserve material compliance along desired folding directions while selectively restricting deformation in unwanted directions. The actuator leverages stiffness tiers based on material thickness, patterned in an origami-inspired geometry with facets and creases, converting unconstrained soft deformation into accurate, repeatable, and composable folding motions without additional reinforcements. The design is fully 3D-printable through a single-material, single-print process that requires no assembly. Each actuator serves as a scalable motion primitive, and linking and orienting multiple actuators mechanically programs multi-DoF trajectories. Using the same fundamental module, we demonstrate three 3D-printed soft multi-DoF robotic systems spanning distinct application domains: (1) a compact 4-DoF wearable haptic device for high-fidelity cutaneous feedback in virtual reality (VR), (2) a 3-DoF joystick for kinesthetic feedback in teleoperation, and (3) a modular robotic gripper capable of underwater operation with geometry-encoded grasp trajectories. These systems demonstrate the module's capabilities for compact multi-axis integration, controlled physical interaction, and geometry-programmed operation across different environments. Together, these results show that MONORIGAMI provides a general, composable, accessible, reliable, and scalable platform for high-precision soft multi-DoF robotics, addressing long-standing limitations in both soft actuator design and fabrication.

In animals such as elephants and octopuses, acquiring non-visual information about an object and physically engaging with it are inseparable processes mediated by rich, large-area interactions between compliant appendages and the environment. Soft robots provide a natural platform for translating this principle into engineered systems. Yet current robotic intelligence makes limited use of physical interaction, treating it primarily as a disturbance to be rejected or, at best, as a means of compensating for object misalignment. Here, we introduce a physical intelligence framework in which distributed compliant interactions jointly reveal task-relevant information and organize manipulation behavior. This results in an intrinsically partially observable problem: key task-relevant information is never measured directly, but must instead be inferred from the history of physical interactions. We propose a reinforcement-learning architecture that addresses this challenge by learning a memory-based control policy end-to-end. The key innovations making this possible are (i) a pretrained exploration policy that provides a reference for broad workspace exploration, (ii) joint optimization that integrates exploration and grasping objectives within a single recurrent policy, and (iii) a two-stage sim-to-real adaptation including observation mapping and policy fine-tuning. We demonstrate this principle through blind whole-arm grasping with a hybrid rigid-soft robotic arm that we equip with IMUs embedded directly within its compliant structure, providing its only source of proprioceptive sensing. The learned policy successfully identifies and grasps various objects by autonomously coordinating workspace exploration, object encounter and localization, inference of grasp-relevant properties, and stable whole-arm wrapping.

Massage therapy is helpful for the rehabilitation of various diseases, such as headaches caused by migraines and stress. Existing robotic systems have focused on massage therapy on the torso and limbs, but performing massage motions through suitable actuation on a person's head has been a challenge. In this paper, we present MiBOT, a head-worn massage robot that actuates two soft tactors to produce touch motions mimicking human massage. A key design principle behind MiBOT is its silent actuation, which we achieve through pneumatic artificial muscles in conjunction with a controller loop to respond to contact pressure. We evaluated the effectiveness of MiBOT in a controlled study and assessed subjects' blood pressure and heart rate levels while applying MiBOT. We found that our mechanical system generated positive and conclusive quantitative outcomes that are similar to the human-administered massage, decreasing participants' mean systolic and diastolic blood pressure by 2.8 mmHg and 1.7 mmHg, respectively, as well as calming their heart rate by 8-10% on average.

Shape and force sensing have long been critical bottlenecks in the development of compact capstan-driven continuum surgical robots, primarily due to the difficulty of obtaining cable tension information within the confined capstan assembly. To overcome these challenges, this paper presents an integrated design-modeling-sensing approach based on the concept of actuation-perception co-design. A compliant element is introduced into the motor mounting bracket of the drive system, enabling micro-deformation under the cable reaction force and thereby allowing real-time cable tension measurement without occupying the compact capstan space. To address the modeling complexity arising from unconventional joint configurations introduced by the spatial cable routing strategy, a parallel computation framework based on a multibody short-thick-beam model is proposed, which captures shear effects in short beam segments and synergistic multi-cable interactions while achieving real-time performance. Building on this framework, stable shape and force sensing is achieved by incorporating a proximal multi-axis force/torque sensor as an additional measurement anchor. Following this design-modeling-sensing framework, capstan-driven continuum surgical robots with single- and dual-segment configurations are developed. Experimental results validate the proposed framework in both single- and dual-segment continuum robots, demonstrating real-time tip pose estimation together with contact force and location perception. By enabling cable tension feedback without compromising the compact capstan architecture, the proposed framework makes integrated perception feasible for capstan-driven continuum surgical robots.

Manufacturing complex soft pneumatic actuators remains challenging because geometric fidelity, compliance, structural integrity, and airtightness must be achieved simultaneously. This study presents a manufacturing-focused evaluation of several fabrication routes for complex pneumatic structures, including heat-shrink forming, silicone casting, powder- and liquid-based additive manufacturing, and fused deposition modeling (FDM). The processes were assessed through process screening, baseline fabrication, failure analysis, and process improvement to distinguish inherent process limitations from correctable manufacturing defects. Heat-shrink forming was limited by geometric conformity, casting by mold accessibility and bonded interfaces, powder-based methods by residual material trapped within enclosed passages, and digital light processing by the material properties and post-processing requirements of the investigated system. FDM provided the most adaptable route because its dominant defects could be progressively reduced through process optimization. The results further showed that airtightness depends not only on nominal wall thickness but also on extrusion-path architecture, while support-free geometry is important when access for internal post-processing is limited. These findings establish a practical design-for-manufacturing approach in which process selection is guided by the compatibility between actuator architecture and manufacturing constraints. The proposed approach provides practical guidance for developing complex, flexible, and airtight soft pneumatic actuators for soft robotic applications

Strictures caused by esophageal cancer can narrow down the esophageal lumen, leading to dysphagia. Palliation of dysphagia has driven the development of a Robotic Soft Esophagus (RoSE), which provides a novel in vitro platform for esophageal stent testing and food viscosity studies. In RoSE, peristaltic wave generation and control were done in an open-loop manner since the conduit lacked visibility and embedded sensing capability. Hence, in this work, RoSE version 2.0 (RoSEv2.0) is designed with embedded Time Of Flight (TOF) and pressure sensors to measure conduit displacement and air pressure, respectively, for modeling and control. Model Predictive Control (MPC) of RoSEv2.0 is implemented to govern the peristalsis and air pressure profile autonomously. The implemented MPC used Sparse Identification Nonlinear Dynamics with Control (SINDYC) models to estimate the future states of ROSEv2.0. The dynamic models are discovered from the TOF and pressure sensor data. Peristalsis waves of speed 20 mm/s, wavelength 75 mm, and amplitudes 5, 7.5, and 10 mm were successfully generated by the MPC. Additionally, RoSEv2.0 with the MPC was employed to perform stent migration testing with various food bolus consistencies. The major contribution claimed in this paper is the application of SINDYC-based MPC to solve the closed-loop control problem of RoSE for achieving desired peristaltic waves.

Reduced-order models based on Cosserat-rod theory are now well established, and modeling theory is no longer the primary bottleneck in soft-robot control. Their implementations, however, do not support the differentiable, GPU-parallel, and control-oriented workflows that underpin advanced rigid-robotics applications. Here, we fill this gap with SoRoMoX (Soft Robot Models in JAX), a fully numerical, JIT-compilable Python/JAX framework. SoRoMoX implements articulated, Piecewise Constant Strain, and Variable Strain models through a unified, control-ready interface that provides inertia matrices, gravitational and elastic forces, Jacobians, and their derivatives. To our knowledge, it is the first rod/strain-based soft-robot modeling framework that runs directly on GPUs and is end-to-end differentiable with respect to states, inputs, and parameters. Sequential CPU rollouts are up to 18.1x faster than state-of-the-art alternatives, while GPU-parallel rollouts increase throughput by up to 234.6x. This performance enables workflows that were previously impractical or impossible: static-equilibrium system identification with 66% lower marker RMSE; residual-force learning with a further 64% reduction; computed-torque tracking with RMSE reduced by a factor of approximately 500 relative to model-free PD; control-gain optimization with up to 62% lower loss than untuned gains; safety-constrained control using high-order control barrier functions to keep the peak contact force within a prescribed 5 N bound, compared with 33.5 N without the safety constraint; and reinforcement-learning policy training up to 7x faster than a CPU PyElastica discrete-rod baseline through massively parallel rollouts.

Acoustic field-driven manipulation provides a non-contact and non-invasive strategy for controlling microscale and nanoscale objects, yet its extension to millimeter-scale robots was limited by insufficient propulsion efficiency in confined biological environments. Here, a coordinated multi-acoustic-field approach is introduced, which harnesses the synergistic action of acoustic radiation forces and acoustic streaming flows to enable controlled locomotion of millimeter-scale helical robots and enhance propulsion. Multiphysics simulations captured the dynamics of millimeter-scale helical robots under combined acoustic fields, and experimental validation demonstrated their locomotion capabilities, including planar navigation, inclined climbing, and vertical motion. Semi-autonomous navigation experiments further confirmed that ultrasonic synergy substantially improved maneuverability. In vitro tests in porcine venous vessels demonstrated that coordinated acoustic fields supported both unidirectional and reciprocating motion under biologically relevant confinement. These findings provide mechanistic insight into scaling acoustic micromanipulation to the millimetre regime and support biomedical applications requiring versatile and controllable robotic mobility.

Visuotactile sensors reconstruct dense contact geometry from measured surface gradients, but host-based processing increases power consumption and introduces data-transfer delays and variable scheduling latency, limiting the sensing and response speed of robotic systems. To address these limitations, we implement a near-sensor computing framework that includes a spectral Poisson solver as a fully streaming hardware pipeline. The computational core logic has an estimated power consumption of 347 mW and achieves high throughput without data-dependent branching or iterative convergence, thereby providing deterministic latency. Operating at 166 MHz, the pipeline produces the first depth value of each 128x128 frame 35,107 cycles after receiving the first input pixel, corresponding to a fixed latency of 0.211 ms. Across 15 contact geometries, the reconstructed depths differ from a double-precision reference by 0.17 % of the peak contact depth. On-chip decisions based on these reconstructions close a robot protective reflex loop in 28.3 +/- 4.9 ms, compared with 169.9 +/- 27.8 ms for an equivalent host-based loop using the same actuator. These results demonstrate that near-sensor reconstruction can provide accurate, energy-efficient, and deterministic tactile geometry on timescales suitable for rapid robotic contact responses.

Continuum robots often operate in uncertain environments, where accurate state estimation is essential for safe interactions. Estimate uncertainty is inherently spatially non-uniform: confidence varies depending on where measurements are available. Global estimation accuracy is not always the top priority, but rather achieving sufficient confidence at task-relevant locations along the robot. This extended abstract introduces mechanically reconfigurable sensing enabling uncertainty-shaping in state estimation for continuum robots. We present a concept hardware design demonstrating the feasibility of longitudinal translation of a sensor within a continuum robot. We demonstrate that state estimation confidence can be reconfigured by varying the sensor location, and show a reduction of full-body shape estimation errors when sliding the sensor back and forth over time, compared to a single fixed tip sensor.

Supportive continuum robots (SCRs) enhance the load-bearing capability of an operative continuum robot by mechanically coupling it with a supportive arm. However, their passive stiffness is determined by the mechanical configuration and cannot be adjusted online for varying payloads or interaction forces. Active stiffness control is therefore needed to regulate the load response and maintain positioning accuracy. Meanwhile, the closed-chain structure introduces kinematic constraints that complicate task-space regulation and stiffness control. This paper presents an active task-space stiffness control framework for a tendon-driven SCR. An existing geometric variable strain model describes the closed-chain dynamics, which are projected onto the constraint-consistent motion subspace. A projected sliding mode controller regulates the operative arm tip while preserving the constraints, and closed-loop stability is established through Lyapunov analysis. After position regulation, active apparent stiffness is introduced through a virtual Cartesian spring based on position-error feedback to shape the force--displacement response. The framework is evaluated in simulation and experimentally validated under prescribed external loads and different desired configurations. Results show that increasing the commanded stiffness gain reduces load-induced tip deflection and increases apparent directional stiffness, thereby improving load resistance and positioning robustness under external loading.

Soft wearable robots have evolved rapidly from proof-of-concept devices into promising platforms for rehabilitation, occupational assistance, and human augmentation. As the field matures, its central challenge extends beyond the development of softer materials and more capable actuators to the integration of sensing, intelligence, and human adaptation into systems that users can wear comfortably, trust, and benefit from over extended periods. This transition motivates the concept of Human-Centric Embodied Intelligence (HCEI), in which intelligence emerges from the coupled human-robot system through the interaction of morphology, multimodal sensing, adaptive cognition, compliant actuation, and the wearer's own physiological and behavioral adaptation. To organize this perspective, this review introduces the Perception-Cognition-Actuation-Augmentation (PCAA) framework, which positions perception and cognition as the primary drivers of design, shifting development beyond the conventional actuator-first paradigm. Using this framework, the review synthesizes advances in soft materials, wearable sensing, artificial intelligence, actuation, human-robot interaction, digital twins, clinical translation, manufacturing, regulation, and ethics, highlighting how these interdependent components collectively shape long-term personalization and real-world deployment. By providing a unified conceptual framework and design perspective, this review aims to guide future research, foster interdisciplinary collaboration, and accelerate the translation of next-generation soft wearable robots toward personalized, predictive, and human-centric wearable intelligence.

In robot-assisted surgery, Forbidden Region Active Constraints (FRAC) represent a control strategy that helps maintain task safety by generating anisotropic haptic guidance to surgeons. However, several challenges need to be overcome before FRAC can benefit teleoperative surgery in a clinical setting. These challenges include the ability to allow for dynamic tissue deformation, maintain energetic passivity, and speed of implementation, among others. In this study, we propose the pipeline design for an energy dissipative FRAC strategy, which accommodates the dynamic tissue deformation caused by respiratory movements, by utilizing a depth sensing camera. The proposed FRAC strategy adopts a fine mesh representation, with a total number of 122,806 polygons in the case study presented, while running at 43.48Hz. We designed in vitro trajectory tracking experiments conducted by a "virtual" surgeon to aid quantitative assessment of the method, including its effectiveness in maintaining task safety, which was confirmed by successfully maintaining a pre-defined safety distance across all trials. We also conducted comparative studies to investigate the robustness and time-efficiency of our method against other FRAC methods that rely on simple geometry AC representations. We demonstrate that our method provides a more robust and effective guidance overall, while maintaining comparable, if not lower, time costs.

Accurate localization remains a key challenge in swarm robotics, particularly for self-reconfigurable systems that must identify relative positions to form diverse structures. Most existing approaches rely on external tracking infrastructure or high-cost sensors, which limit scalability and deployment in unstructured environments. In this paper, we propose a novel contact-driven localization method for modular robots that leverages only local communication through binary contact information (whether two robots are physically connected or not). To exploit these contact cues, we introduce a virtual-force framework in which robots iteratively refine their poses attracting toward dock-connected neighbors and repelling from non-connected ones. The method requires no external infrastructure and relies only on minimal onboard sensing. Simulations show effective localization during the assembly of towers and cantilevers, enabling accurate, scalable, free-form self-assembly.

Soft robotic substrates are promising for Physical Reservoir Computing (PRC) because their compliant nonlinear dynamics can provide temporal memory, high-dimensional state transformations, and efficient inference. However, physical reservoirs are often adopted as-is rather than pretrained or co-optimized, potentially limiting soft robotic PRC performance relative to digital reservoirs. We investigate whether a physical reservoir can instead be pretrained against high-performing digital reference dynamics. Our formulation jointly optimizes physical parameters, a diffeomorphic physical-reference state map, and feedforward-feedback control using a differentiable physical model and an acceleration-level equation-error objective that avoids temporal integration. As a proof of concept, we instantiate the formulation with simulated soft robots, a Random Oscillators Network (RON) reference, and parallel multi-start gradient descent. We evaluate the optimized reservoirs on classification (sMNIST and ADIAC) and forecasting (Mackey-Glass and Lorenz96) tasks across four reservoir dimensions. Compared with unoptimized soft robot reservoirs, the optimized reservoirs achieve a mean relative improvement of 33.7% across all tasks and datasets, while remaining close to the digital reference. These results demonstrate the feasibility of dynamics-level co-optimization for the simulated soft robotic reservoirs considered here.

The deployment of deep neural networks for visual affordance segmentation on wearable robots poses may prove critical, due to some conflicting aspects of the problem. On one hand, affordance segmentation requires high-level abstraction capabilities, that typically involve large-size models. On the other hand, computing resources hosted on wearable robots prevent to run large-size models in real-time. The paper presents an analysis of the role of the segmentation head in the trade-off between generalization performance and compute cost. The obtained models outperform modern baseline solutions in well-known, real-world datasets while meeting low computing requirements.

While depth sensors have the potential to complement RGB data for affordance segmentation in wearable robots, their usage seems to remain underexplored. The paper proposes two approaches: a reformulated version of hardware-aware neural architecture search, endowed with a newly designed search space to integrate depth (D) information into small-sized deep networks, and a dedicated fine-tuning approach, including a preprocessing layer to merge depth information with RGB data and make it compatible with conventional architectures. In both cases, those methods aim to generate solutions that benefit from modern (portable) hardware accelerators and overcome existing tiny-like approaches, which often fail to tackle critical scenarios due to the severe constraints set by the supporting hardware. Extensive experiments on a pair of real-world datasets demonstrate the effectiveness of the proposed method as compared with existing solutions. The approach presented in the paper generates, in most cases, solutions that identify the Pareto optimal front to balance generalization performance and hardware requirements. The paper also describes the supporting prototype, including a Jetson Nano board and a RealSense RGB-D camera. When considering the energy profile of the device, the overall system can attain real-time performances within an energy budget that is compatible with standard batteries, such as those used in smartphones.

Recent advances in robotics research have created a strong demand for high-performance simulators. Surgical robotics simulation faces unique challenges due to the need to model diverse objects, such as rigid instruments, soft tissue, and fluids. While many studies simulate sutures or soft tissue independently, only a few have considered the complete soft-tissue suturing scenario, including the contact between sutures and deformable tissue during suture insertion. Building on previous work, this paper presents a novel suturing simulation environment using sutures modelled by position-based dynamics (PBD) and soft bodies modelled by the material point method (MPM) while considering two-way contact with frictional and drag forces. We introduce a contact coupling method between the PBD suture and the MPM soft tissue, enabling visually plausible suture-tissue interactions. The simulator is optimized for GPU execution with parallel scenes using multiple CUDA streams, and we present a Reinforcement Learning (RL) environment for autonomous suturing sub-tasks, including needle insertion, driving, and extraction. Using ML-Agents, RL agents trained in the simulator show stable learning and achieve 80% and 68% success rates in needle insertion and extraction, respectively, under the strictest distance threshold.

A cable-driven continuum robot arm is an underactuated mechanism and may suffer residual vibration at the end of a rest-to-rest maneuver. In this work, a time-delay filter is applied as an input shaper to the system to eliminate the excitation of vibratory modes. A non-robust and a robust time-delay filter are designed based on a linear system model and demonstrate improved response compared to a velocity-driven pulse input. Experimental results using the continuum robot validate the application of the input shaper, with reduced overshoot and settling time exemplifying the reduction in oscillation at the end of the maneuver. It is also shown that utilizing the robust shaper further improves the response of the arm in comparison to applying the non-robust shaper. These results are significant towards the precise and robust implementation of continuum robots in applications involving arbitrary end-effector trajectories.

Precise control of soft manipulators remains challenging due to the difficulty of developing accurate yet computationally tractable models for model-based estimation and control. Reduced Cosserat-rod models provide a physics-based and control-oriented description of soft-robot dynamics, offering an explicit alternative to purely data-driven input-output representations. In this paper, we propose a moving-horizon estimation (MHE) and nonlinear model predictive control (NMPC) framework for cable-driven soft manipulators based on reduced Cosserat dynamics. A smooth cable-length-driven modeling formulation is developed by approximating the complementarity relationship between cable tension and cable slackness, enabling cable-length control without direct tension sensing. Based on this formulation, an MHE method is introduced to estimate the reduced state and reconstruct the manipulator configuration from end-effector pose measurements and cable-length information. An NMPC controller is then formulated to achieve task-space control under cable-length and cable-rate constraints. The proposed framework is validated through numerical simulations and experiments. Simulation results demonstrate the effectiveness of the estimator and controller for pose and strain-related regulation on a multi-cable soft manipulator. Experimental results on a four-cable prototype further show that the proposed MHE-NMPC scheme can be implemented in real time and enables accurate end-effector position tracking through cable-length control.

Nociception is a protective biological mechanism that links harmful stimulation to a reaction. This paper investigates artificial nociception for a robotic arm with whole-body tactile sensing. We present a complete pipeline that maps pressure changes from sensitive skin on a robot manipulator to bio-inspired withdrawal motions. The system first converts skin pressure into a scalar pain gain using a nonlinear continuous model. We compare three reflexes: (i) uniform reflex moves four robot joints by a fixed amount, whereby the withdrawal is approximated by a movement of the arm "toward the base", independent of where the robot was touched; (ii) biologically motivated location-dependent joint-space withdrawal derived from human withdrawal reflex characteristics; (iii) Cartesian space withdrawal along the surface normal of the contacted skin pad. All behaviors are integrated in a reflex controller that interrupts the task, executes the withdrawal, and returns to a pre-contact pose. A user study with 15 participants compared the strategies using Godspeed questionnaire subscales, custom perceived-naturalness and safety items, forced-choice comparisons, and qualitative feedback. Interestingly, participants rated more highly the uniform reflex behavior over one or both competitors on the anthropomorphism, animacy, and likeability Godspeed subscales and on the Naturalness and Realism custom scale. When asked to compare the conditions, the uniform reflex was scored best in "felt safest", "most human-like", and "most natural". This suggests that predictability of the robot behavior is key for user acceptance. The Cartesian reflex was judged the most appropriate reaction to touch. The bio-inspired reflex did not lead any evaluated measure. This may be partly attributed to the embodiment gap between the robot arm and human arm and participants having different expectations from a robot manipulator.

Autonomous robotic craniotomy requires continuous regulation of tool-tissue interactions to mitigate mechanical overload and thermal damage while maintaining surgical efficiency. However, this process is inherently partially observable due to unknown, time-varying tissue properties and the inability to directly measure cutting temperatures under physical occlusion. To address these challenges, we propose RL-MACRO, a cybernetic closed-loop intelligence framework that couples multimodal perception, adaptive decision-making, and robotic execution. This framework empowers the surgical robot to autonomously perceive inaccessible states from partial sensory feedback and dynamically optimize its behaviors under uncertain environment. A CNN-LSTM observer first fuses force and sound feedback to reconstruct the hidden temperature state (R^2=0.939, MAE = 1.717 deg C). This reconstructed temperature, alongside multi-sensor features, forms the belief state for an offline Implicit Q-Learning (IQL) policy. A novel dual-head Actor dynamically coordinates the feed rate, spindle speed, and cutting depth to optimize efficiency within strict safety bounds. These decisions are seamlessly translated into spatial motions via online trajectory re-planning and velocity servoing. Experiments on bovine ribs and six ex vivo goat skulls validate the system's robust perception, adaptive recovery from force/temperature excursions, and smooth execution on irregular surfaces, establishing a data-driven cybernetic paradigm for safe and efficient autonomous bone cutting.

Manual craniotomy is a high-risk, skill-dependent procedure associated with surgeon fatigue and potential dural injury. While robotic approaches have improved safety, existing open-loop systems rely solely on preoperative images and cannot compensate for intraoperative registration errors or tissue deformation. To address this, we propose a human-inspired closed-loop robotic craniotomy framework that intelligently integrates preoperative planning with intraoperative execution. An adaptive dual-contour fusion algorithm is employed to generate trajectories that conform to complex cranial geometries while maintaining a consistent tool-bone relative pose. For intraoperative perception, a multimodal two-stage cross-modal attention block (CMA)-temporal convolutional network (TCN)-Transformer network combined with an adaptive Bayesian filter fuses force and acoustic signals to achieve robust breakthrough detection under varying bone conditions. Upon detection, an in-situ projection-based trajectory adjustment strategy dynamically compensates for depth deviations, enabling safe residual bone isolation. Experiments on bovine ribs show a breakthrough prediction accuracy of 97%, a detection latency of 0.048 +/- 0.097 s, and a maximum overshoot of 0.29 mm. All four ex vivo cranial experiments were successfully completed without dural injury. These results demonstrate that the proposed cybernetic framework enables safe and autonomous craniotomy with highly effective closed-loop control.

Soft robot exteroception is increasingly being explored for a variety of field applications. In this work, we present a sound-based system for localizing disaster victims in confined and unstructured environments, based on a distributed acoustic sensing architecture embedded along the body of a soft everting vine robot. We propose a dynamic Steered Response Power with Phase Transform framework that supports both far-field direction-of-arrival estimation and near-field three-dimensional source localization as the robot approaches the sound source. To better understand the design and control space related to localizing sound using a soft, shape-morphing robot body, we conduct experiments measuring the accuracy of these methods for a five-microphone array attached to the robot body using three placements relative to the outer membrane of the robot (inside the pressurized body, inside the inner tail, and outside the outer wall) and in four robot configurations (linear, double linear, circular, and sinusoidal). We measure the change in accuracy as the signal-to-noise ratio, the direction of approach, and the distance of the sound source from the center of the array change. Finally, we demonstrate a vine robot growing into an arbitrary shape while carrying microphones along its outer wall, and show that a sound source located with the array's near field can be localized with high accuracy after only three microphones have everted from the robot body. These results highlight the potential of distributed acoustic sensing for reliable victim localization using soft growing robots.

Safe navigation within the spinal subarachnoid space is constrained by its narrow, compliant, and delicate anatomy. Conventional catheters and continuum robots rely on proximal pushing, generating friction and shear along the tissue device interface that limit distal controllability and increase the risk of neural injury. Here, we present a 2 mm diameter eversion-growing robotic platform that enables friction minimised extension and steering within the human spinal subarachnoid space, validated through computational modelling, phantom experiments, and intact human cadaver studies. The robot integrates a miniature endoscope for real time intrathecal visualisation and advances by pressure driven tip eversion, localising motion to the distal tip while minimising translational sliding of the deployed body. Phantom experiments demonstrated reductions of 65.2% in mean interaction force and 48.0% in peak interaction force compared with matched push-based insertion. Physics based modelling showed that eversion based growth redistributed tissue loading, reducing local stress concentrations and interfacial shear relative to conventional insertion. In an intact human cadaver, the system achieved 150 mm of controlled intrathecal extension with concurrent fluoroscopic and endoscopic visualisation, providing access across multiple vertebral levels from a standard lumbar entry point. Postprocedural laminectomy and durotomy revealed no observable macroscopic disruption of the dura mater or surrounding neural structures. These results provide the first mechanically characterised and multimodally validated demonstration of eversion-based robotic navigation in intact human spinal anatomy, establishing a quantitative and procedural foundation for future intrathecal interventions. Further validation in larger anatomical cohorts and under physiological conditions will be required before clinical translation.

Fast prediction of the response of adhesive soft viscoelastic contacts represents a current challenge in soft robotics and for gripping and manipulation tasks. Determining the complete time-resolved force trajectory requires full numerical simulations, whose computational cost is strongly parameter-dependent, making them impractical for real-time application or design-optimization loops. In this work, we overcome this limitation by training a scalar-conditioned, stateful, sequence-to-sequence deep learning model to predict the full force evolution from a prescribed displacement history for both short- and long-range adhesion regimes. The data set spans four orders of magnitude in loading and unloading rates and includes varied dwell times, with the Tabor parameter ranging from $0.2$ to $3.2$. To enable learning across these heterogeneous time scales, we introduce a fixed-measurement-step (FMS) representation that converts variable-length trajectories into fixed-length sequences while preserving their physical-time information. Different architectures were trained, including long short-term memory (LSTM) networks, temporal convolutional neural (TCN) networks, and time-distributed dense layers with three different Tabor-conditioning mechanisms. The models were compared using global waveform and error metrics. We found that the best-performing model has an LSTM architecture with concatenated conditioning, which achieves a held-out mean-squared error of $5.0\times10^{-4}$, a median pull-off-force error of $\approx2.2\%$, and a median hysteresis error of $\approx1.1\%$. For the held-out protocols, the model predicts a complete force trajectory with a median inference time of $0.16$ s. The model is tested across unseen parameter combinations and against analytical limiting cases, providing a rapid surrogate for repeated numerical evaluations with potential use in control-oriented applications.

Robot sensors and electronic equipment are prone to failure in harsh environments. With water hydraulic drive, thin and long tubes enable remote operation without actuator-side sensors. Furthermore, the elasticity of the tubes reduces the impedance of the joints (actuators), benefiting robot tasks involving unexpected contact with the environment or vibrations. However, owing to the low impedance and limited camera visibility, accurately positioning the joint (or end effector) to the target location under varying load conditions is challenging. This study proposes a novel method that employs water-filled flexible tubes to enable the transmission of driving power and actuator-side information to and from the actuator, respectively, without actuator-side sensors. By modeling volumetric loss during transmission based on pressure fluctuations and incorporating minor air entrapment, simultaneous power transmission and position estimation is achieved through a tube up to 50 m. Thus, it becomes possible to use a feedback control framework that was previously difficult to implement in sensorless systems. Experimental validation confirms stable position control of a sensorless water hydraulic cylinder under varying loads. Furthermore, a field parameter-identification method accounts for tube and air entrainment variability without requiring actuator-side sensors. These contributions promote reliable remote control of robots in harsh environments.

Robotic systems increasingly demand tactile sensing that approaches the adaptability and resolution of human skin to enable dexterous manipulation and safe interaction. OptiTac is a biomimetic tactile sensor that emulates the mechanoreceptor-to-nerve architecture of human touch by pairing each mechanical pin on a soft skin with an optical fiber acting as an artificial nerve. This design demonstrates an architectural principle for routing tactile information away from the sensing surface while preserving high spatial resolution, establishing a practical route toward distributed tactile sensing in future robotic systems. By treating tactile signals as images, simple analytical methods, rather than opaque deep-learning models, are used to infer contact location, size, and shape, providing interpretable and scalable tactile intelligence. This work demonstrates how evolutionary principles from biology can guide the development of artificial nerve systems for robots, offering a pathway toward human-like tactile perception in next-generation robotic platforms. More broadly, OptiTac establishes an artificial nerve-inspired sensing framework for interpretable robotic touch and a scalable route toward future distributed tactile systems.

Soft continuum robots require embedded sensing for proprioception and contact detection, yet integrating sensors into sparse, highly deformable architected structures remains challenging. We present a model-based strategy that decouples proprioceptive and contact signals from a common set of fluidic pressure sensors embedded in a soft architected segment. Each segment of the Innervated Trimmed Helicoid (ITH) contains six air channels routed in a localized zigzag pattern along the circumference. With only three principal kinematic degrees of freedom (axial compression, bending in x, bending in y), the six pressure readings form an overdetermined system. A piecewise constant curvature model maps pressures to shape, and Huber regression identifies outlier channels whose residuals indicate external contact. On a single ITH segment, this approach achieves proprioceptive shape estimation with a relative bending error of 0.11 +/- 0.02 and a contact detection rate of 97% across 178 trials. We integrate eight ITH segments into Air-Helix, a tendon-driven soft continuum manipulator, and present exploratory whole-arm demonstrations that include tactile teaching by demonstration, admittance-controlled force regulation, and tactile object reconstruction. The results suggest that localized fluidic innervation combined with model-based redundancy resolution is a practical path toward concurrent proprioception and contact sensing in architected soft robots.

Continuum robots provide intrinsic compliance, high dexterity, and safe physical interaction, enabling navigation and manipulation in confined and unstructured environments. Despite recent advances in sensing and control, heightening the need for precise motion generation, most widely used planning libraries are grounded in rigid-body assumptions, creating a critical gap for fast and practical tools for continuum robots. To address this, we present CR-Solver, a two-stage, optimization-based solver for the motion generation of tendon-driven continuum robots. Our method unifies inverse kinematics, path following, and trajectory planning within a single constrained nonlinear optimization framework. Leveraging GPU-accelerated parallel optimization, CR-Solver delivers fast, accurate, and constraint-aware solutions. We validate our approach on three tasks, demonstrating significant speedups over traditional CPU-based solvers while achieving a consistently high success rate above 95% and millimeter-level accuracy. The solver is implemented in pure Python, reducing the barrier to adoption and offering a practical, extensible foundation for continuum robots' high-performance motion planning.

The development of assistive robots for dressing tasks serves to augment human convenience and improve the quality of life for individuals with physical impairments. However, due to the intricate contact interactions between garments and the human limbs during dressing, most robot-assisted dressing algorithms treat clothing as an assembly of discrete segments, thereby struggling to manage the partial worn garments under contact constraints. To overcome this challenge, we propose a novel robotic dressing control algorithm that integrates realtime differentiable clothing simulation. The simulation algorithm employs explicit iterative scheme with intentionally introduced higher-order perturbations to enhance computational efficiency while maintaining stability under large time-step conditions. Through simulation, we resolve the garment state under contact constraints, which then enables a multi-phase control strategy for successful coat dressing assistance. To further improve real-time performance, we introduce a constrained local model along with its corresponding optimization solver, permitting high-frequency local compensation for the differentiable simulation based global controller. Finally, we experimentally validate our approach through both simulated and physical dressing scenarios, conclusively demonstrating its feasibility and efficacy

Conventional colonoscopy remains limited by patient discomfort and procedural risks, motivating research into compliant robotic alternatives. Eversion robots, which advance via pressure-driven tip growth, eliminate sliding friction against the colon wall and offer a less intrusive approach to traversal. However, no existing design simultaneously satisfies all clinical requirements. This paper benchmarks four recent eversion robot architectures against the key anatomical and clinical constraints of colonoscopy, including colon length, minimum luminal diameter, bending angle, and working-channel needs. We identify the central trade-offs each design reveals, particularly the difficulty of integrating steering and payload delivery without sacrificing the soft, low-friction behaviour that makes eversion robots attractive. We then provide design guidance across material selection, steering strategy, and payload delivery, and highlight open problems for clinical translation.

The elephant trunk is a dexterous and versatile manipulator whose performance is still unmatched in robotics. In previous works, modularity was prioritized and relatively small-scale continuum robots were built. We take the natural proboscis of the Loxodonta africana species as a model and propose a different design approach which favors structural continuity and dynamic properties that plausibly emulate those of the natural trunk, while conferring high adaptability to the environment and humans. Instead of targeting prescribed behaviors, we show that a biomimetic design based on the macroscopic properties of the natural system enables elephant-like movements and grasping. We build by 3D printing an 85 cm long, compliant, tapered, volumetrically tessellated continuum arm, which is combined with tendon-driven actuation mimicking the longitudinal and oblique muscles of the natural model. We demonstrate whole-body grasping of objects having different shapes and dimensions and discuss a comparison to the biological trunk highlighting aspects of both biology and robotics.

Soft robots have attracted significant attention in applications such as medical intervention, rehabilitation, and robotic manipulation due to their inherent compliance, flexibility, and high degrees of freedom. Modular soft robots (MSRs), composed of multiple interconnected segments, represent an emerging class of robotic systems with highly deformable and reconfigurable structures capable of performing complex tasks. However, designing controllers for MSRs remains challenging due to their nonlinear dynamics, modeling complexity, and hyper-redundant nature. Existing approaches typically require controllers to be retrained from scratch whenever the robot morphology changes. In this work, we address these challenges through a continual learning inspired control framework capable of incrementally adapting to changes in robot morphology while preserving previously acquired knowledge. Specifically, the proposed framework enables the controller to sequentially learn new MSR configurations without forgetting previously learned ones. In addition, for MSRs with fixed configurations, the same framework can be employed in a distributed manner to learn module-specific dynamics, enabling localized control and improved precision. The proposed approach is validated through closed-loop trajectory tracking experiments in simulation using a tendon-driven soft robot, as well as on a real-world three-module pneumatic soft robotic arm. Furthermore, we demonstrate the adaptive capabilities of the framework through a reaching experiment in which the controller selectively activates only the necessary modules to reach a virtual target position, thereby reducing computational overhead.

Beryllium contamination surveys in radioactive areas are challenging for robots in environments cluttered with cables and electronics. To address this problem, we have developed a novel quadruped system augmentation: A lightweight, soft, and compliant tendon-actuated robotic tail mounted on a quadruped robot. The tail features a hollow, flexible backbone and a tendon-actuated soft gripper that enables the robot to pick up sampling tissues, swab contaminated surfaces, and release the tissues at designated collection locations for subsequent beryllium analysis. To enable intuitive teleoperation, a closed-form kinematic model and a singularity-robust task-space controller are developed. Experimental results demonstrate that gripper actuation has a negligible effect on robot shape, while common-mode tendon actuation provides an effective mechanism for stiffness modulation and preload control. Furthermore, experimental validation indicates that the proposed kinematic model provides a suitable basis for real-time task-space control. The proposed system combines the agility of legged locomotion with the compliance of soft robotic manipulation, enabling the complete contamination-survey procedure to be performed without human exposure. While motivated by beryllium contamination surveys at CERN, the proposed quadruped soft-tail concept is broadly applicable to legged robots operating in cluttered, confined, or hazardous environments where conventional rigid-link manipulators are undesirable.

Robots working in unstructured or partially unobservable environments must combine accurate motion with physical compliance that can passively correct contact misalignment. Soft robots provide this compliance but have struggled to precisely control their tip compliance and position. This paper presents a robot architecture designed around that control problem: a 7-link arm whose six articulated joints provide twelve independently driven revolute axes, each actuated by an antagonistic pair of pneumatic muscles, so that every axis can simultaneously change its angle and linearly adjust its stiffness. The rigid articulated backbone makes the tip compliance and position of the arm predictable enough to be commanded quantitatively in real time. The robot employs a unified iterative inverse-kinematics and inverse-compliance controller to achieve simultaneous, quantitative control of both compliance and position. The task-space compliance and kinematics models and the control law are derived and verified on both the physical arm and a matched simulation. Simulation is then used to study how the same framework extends to other arm morphologies. Finally, the arm demonstrates tasks that have been difficult for both rigid and soft arms: rejecting disturbances while writing on a moving whiteboard, and passively correcting hidden misalignment during a key-insertion and drawer-opening task. That these tasks succeed under so straightforward a controller is evidence for the advantage of this algorithm-informed structural design.

Continuum robots offer key advantages in navigating unstructured environments, but their safe operation requires accurate estimation of the external contact forces acting anywhere along the robot body. Estimating these forces at unknown locations is an ill-conditioned problem, particularly for multiple contacts. We propose a unified shape and force estimation framework formulated on a factor graph. By incorporating a Gaussian mixture force parameterization into a discretized probabilistic Cosserat rod model, we reduce the dimensionality of the unknown external forces and mitigate the ill-conditioning of node-wise force estimation. The framework fuses strain, tendon tension, and pose measurements to simultaneously estimate the robot's shape and external forces while accounting for modeling and sensor uncertainties. Numerical simulations demonstrate that the proposed method outperforms existing methods in terms of force location and magnitude estimation for both single and multi-contact scenarios. We further present a progressive variant that introduces basis functions on demand to estimate contact forces sequentially during a simulated confined-navigation task.

Soft robots are challenging to control due to their nonlinear and time-varying dynamics. Data-enabled predictive control (DeePC) offers a model-free alternative by directly leveraging measured input-output trajectories to construct a predictive controller. However, its receding-horizon formulation requires solving a constrained optimization problem at every sampling instant, which can be computationally demanding for real-time deployment on resource-limited robotic platforms. To address this limitation, we propose an adaptive reinforcement-learning-based event-triggered DeePC (RL-ET-DeePC) framework for soft robotic control. A model-free RL policy is trained to determine when to invoke the DeePC optimizer based on the current system state representation, thereby reducing unnecessary optimization calls while preserving closed-loop performance. Simulation results show that RL-ET-DeePC reduces optimization frequency by up to 66% compared to periodic DeePC, while maintaining comparable tracking accuracy. Hardware experiments on a three-dimensional cable-driven soft robotic arm demonstrate zero-shot transfer, achieving a 34% reduction in optimization frequency with tracking accuracy comparable to periodic DeePC and more consistent performance than a static threshold-based event-triggered baseline.

Learning contact-rich, whole-body manipulation for soft continuum robots is held back by the lack of simulation infrastructure that has accelerated rigid-robot manipulation. Existing soft robot simulators are physically grounded but lack the contact handling, actuation support, or learning integration needed for contact-rich manipulation; rigid-body approximations offer these capabilities but sacrifice physical grounding. We bridge this gap for tendon-driven continuum robots (TDCRs) by deriving a continuum-mechanics-informed discretization that places the soft robot natively inside MuJoCo, unifying tendon forces, body contact, and dynamics in a single physics pipeline. We validate the simulator against a Cosserat rod reference (static and dynamic) and real TDCR hardware. We then train state-based imitation learning policies via teleoperation in simulation and deploy them zero-shot to a physical 3-segment TDCR on a 7-DoF Franka arm across two contact-rich manipulation tasks. To our knowledge, this is the first demonstration of sim-to-real transfer for contact-rich manipulation with continuum robots.

Magnetically programmable soft elastomers enable complex shape morphing and locomotion dynamics in small scale soft robots under external magnetic fields. Benefiting from their programmed deformation and wireless actuation capabilities, magnetic soft robots have emerged as promising platforms for targeted drug delivery, especially in human gastrointestinal tract. However, achieving controlled directional liquid cargo release toward desired tissue interface while preserving the encoded shape morphing and locomotion capabilities remain a significant challenge. Here, we report a new design strategy that employs an optimized magnetization profile to enable controlled directional release of aqueous cargo without compromising shape morphing and locomotion capabilities. Magnetic soft robots with a specific spatially distributed magnetization profile allow directional alignment of the release interface with the orientation of the external magnetic field. This orientation control ensures active alignment of the release interface toward the intestinal wall prior to drug release. An interconnected microporous elastomer is embedded within the robot for aqueous cargo storage, while a thin microcrystalline wax layer seals the release opening hole to isolate the stored liquid cargo from external environment during transport. Triggered release is achieved by mechanically rupturing the wax sealing layer under a higher magnitude external magnetic field. Controlled directional flipping, locomotion, and triggered release are decoupled through external magnetic field's direction and strength. The controlled directional release strategy reported here integrates directional targeted liquid cargo release, shape morphing, and locomotion, which establishes the groundwork for target drug delivery in gastrointestinal tract applications.

In this paper, we present a fully discrete approach for the accurate and numerically efficient dynamical modeling and state estimation of continuum robots. The model is based on geometrically exact beams in a minimal, strain-based formulation and derived in the framework of Lie group variational integrators, allowing to preserve important geometric properties that we exploit to achieve high accuracy and numerical efficiency. We then propose a disturbance observer based on an extended Kalman filter formulation that reliably estimates system states as well as model uncertainties and external disturbances. Experiments on a real system validate the accuracy and efficiency of the proposed model and observer.

Modeling soft robot dynamics is challenging due to their continuum structure and typically nonlinear dynamics. Creating models based on first-order principles is typically time-demanding, and their expressiveness is limited, whereas data-driven models lack interpretability and physical consistency. This work aims to overcome these challenges by introducing a port-Hamiltonian Gaussian Process Regression framework for learning and simulating the dynamics of planar, rod-like soft robots. In detail, the proposed model integrates Cosserat rod theory and Hamiltonian physics with data-driven inference to preserve the system's energy structure while accurately learning the rod dynamics. Numerical simulations show that we can achieve accurate and energy-consistent representations of a rod-like soft robot, showing the potential for a robust and interpretable pathway for modeling complex continuum mechanics.

This paper presents an experimental study of motion planning for resilient continuum robots. In this study we mainly focused on multi-criteria decision-making, its application for path-planning algorithms, impact on the generated path and execution time. To do this, we used two well-known algorithms for path planning, namely Genetic algorithm and A star algorithm, and modified them by adding the Analytical Hierarchy Process algorithm to evaluate the quality of the paths generated. In our experiment the Analytical Hierarchy Process considers four different criteria, i.e. distance, motors damage, mechanical damage of the robot's arm and accuracy, each considered to contribute to the resilience of a continuum robot. The use of different criteria is necessary to increase the time to maintenance operations of the continuum robot. We conducted the experiments using two different simulated environments of the robot. Although we significantly simplified the robot's model and its environment, we still implemented some of the features of the environment based on the real robot prototype. In particular, one of the environments has single- as well as multi-path points, and other consists of the multi-path points only. The results show that, in contrast to A star, the performance time of Genetic algorithm does not depend on the environment's cardinality. It generates more diverse paths, which increases the robot's resilience.

Continuum robots offer strong potential for manipulation tasks due to their high degrees of freedom, compliant structures, and operational safety. However, their adoption in both research and practical applications has been hindered by reproducibility issues arising from complex fabrication and assembly processes, challenging kinematic modeling, and a lack of intuitive control interfaces. To address these challenges, we present a novel open-source continuum robot design. The platform features a simplified fabrication pipeline enabled by multi-material 3D printing, allowing the arm to be fabricated as a monolithic compliant structure with minimal assembly. Control is achieved through an isomorphic teleoperation interface that establishes a direct actuator-level mapping, eliminating the need for explicit kinematic modeling and providing a singularity-free mapping. Building on this hardware design, the platform further supports imitation-learning-based autonomous control. The proposed system is evaluated through hardware characterization and a set of manipulation tasks. Experimental results demonstrate that the platform provides a reproducible, learning-ready continuum robot system, accelerating algorithmic development and systematic benchmarking for the continuum robotics community.

Continuum robots offer a promising approach for minimally invasive and natural-orifice surgical procedures due to their inherent compliance and dexterity. However, this flexibility also makes estimating the current shape of the robot challenging. Several approaches have been used to reconstruct the shape of these robots, including imaging, optical sensing, magnetic sensing, and resistive sensing. Strain sensors fabricated using direct laser writing (DLW) could provide an alternative sensing method. This technique involves using a laser to induce carbonization of certain polymers to create graphene patterns, such as strain sensors. In this paper, we demonstrate how a flexible continuum joint and a DLW sensor can be machined as one monolithic structure using the same laser and the same setup. The fabricated sensors are characterized using linear and nonlinear models, which are used to predict the joint angle with error as low as 1.76 degrees. Furthermore, we demonstrate how a DLW sensor can be used to implement closed-loop control in a robotic joint, achieving tracking error under 3 degrees.

Soft lattice structures are increasingly used in robotics to tailor compliance and guide deformation; however, actuation is typically introduced at the device or module level, with actuators inserted into otherwise passive architectures. In this work, we move actuator-lattice co-design to the unit-cell scale. We present an embedded pneumatic unit cell that integrates curved-strut lattice geometry with a bidirectional bellow actuator within a single monolithic element. When tessellated, the lattice functions as a distributed actuation field in which global morphology is governed by spatial actuation patterns rather than uniform pressurization. Experimental characterization of 1x1, 2x2, and 3x3 tessellations demonstrates scalable displacement and force generation with repeatable cyclic performance. Selective actuation of unit cells in a 3x3x3 array produces distinct global deformation modes, including bending and directional grasping, without altering hardware configuration. Additionally, coupling active and passive unit cells enables bending-driven crawling locomotion, demonstrating that heterogeneous tessellations can translate through asymmetric deformation. These results establish unit-cell-level actuation as a strategy for distributed morphing in lattice-based soft robots and provide a foundation for scalable, monolithic robotic architectures.

Adaptation to damages and in-situ physical repairs is essential for long-term robot autonomy, yet challenging outside of narrowly defined and well-anticipated bounds. In this work we proprioceptively adapt to catastrophic damage in soft-actuated systems in under one minute. Architected materials are well equipped for adaptation: actuator failure occurs gradually rather than acutely, and damage can be described in a low-dimensional, discrete coordinate space. Surprisingly, latent damage representations plus a simple yet robust ensemble method is sufficient for adapting to unseen damage in real-time. Moreover, we identify conditions under which exponential sample complexity collapses to linear sample complexity for learned representations of architected materials, a concrete advantage over rigid components or continuum soft mechanisms. We demonstrate LEAP, our method for adaptive proprioception, via a tracing task for a 6DoF soft wrist based on Handed Shearing Auxetic (HSA) actuators. Our algorithm is able to adapt to cuts, burns, and actuator repairs, enabling simulation-free real-time adaptation that is critical for realizing the promise of soft robots outside the lab. Videos and more information are available at https://murpheylab.github.io/leap.

Soft robots leverage compliant materials to generate motion through controlled elastic deformation, making them ideal for delicate tasks such as underwater exploration and biomimetic marine systems. Although hydraulic/pneumatic actuation remains pivotal for such systems, the lack of systematic design frameworks has hindered the development of robots capable of complex 3D motion, such as fish-like swimming. This work introduces a topology optimization method to automate the design of a hydraulic soft fish tail, explicitly addressing the design-dependent coupling between fluidic actuation and structural deformation. We use a Darcy law-based model augmented with a drainage term to simulate spatially varying hydraulic pressure loads, translating these into consistent nodal forces via finite element analysis. The employed robust multi-criteria optimization formulation balances deformation efficiency, fluid-structure interaction, geometric manufacturability, and required stiffness for optimizing a bioinspired soft fish tail for 3D swimming kinematics. The optimized tail topology is incorporated into a pneumatic network actuator and computationally validated under various hydraulic loads, achieving tunable undulatory amplitudes and multiaxis bending for depth adjustment. The optimized 2D tail outperforms its rectangular counterpart. By cascading optimized tail segments, we demonstrate programmable swimming patterns in soft robotic fish tails at different hydraulic loads. This work advances the systematic codesign of hydraulic actuators and soft structures, offering a pathway to automate underwater robots with optimized design and vertebrate-like agility in confined aquatic environments. Our implementations and simulations are publicly available at 'https://github.com/PrabhatIn/TO-SoFiT'.

This document proposes a novel approach to hardware-aware neural architecture search (HW NAS) that considers the resources available on the computing platform running it, enabling its execution on various embedded devices. The presented HW NAS produces tiny convolutional neural networks (CNNs) targeting low-end microcontroller units (MCUs), typically involved in the Internet of Things (IoT) or wearable robotics, opening new use cases. A gateway could run it to tailor CNNs' architecture on the acquired data without using external servers, ensuring privacy. The proposed technique achieves state-of-the-art results in the human-recognition tasks on the Visual Wake Word dataset, a standard TinyML benchmark, on several embedded devices.

Existing stretch and touch sensors for robots are generally expensive with respect to at least one of material costs, required manufacturing equipment, or manufacturing time. We present and experimentally characterize a conductive fiber made using only inexpensive commercial off-the-shelf parts (conductive thread at $0.07/ft, silicone tubing at$0.94/ft) and tools (loop-style needle threader at $2), which can be manufactured quickly (20 cm length in 2 minutes.) We demonstrate its use as a resistive strain sensor with three applications: Triggering a grasp in a pneumatically actuated assistive finger, sensing the pose of a pneumatically actuated robotic strap, and estimating the pose of a flexible solid. We also demonstrate that it can be used as a capacitive sensor with two applications: First, as a touch sensor which triggers a commercial robot arm to move, and second, as a near-field sensor enabling the robot arm to follow a moving hand. The capacitive sensors are knitted, showcasing the high flexibility of the fiber. We discuss methods for improving manufacturing scalability and their cost trade-offs. Finally, we demonstrate a method for repairing a cut fiber.

Contact-rich manipulation requires force sensitivity, but many robot arms lack dedicated force sensors due to their high cost. We present Neural External Torque Estimation (NEXT), a data-driven method that estimates external joint torques without needing any dedicated force sensors. NEXT trains in 1 minute from only 10 minutes of free-motion data, yet achieves estimates comparable to dedicated joint-torque sensors. NEXT enables force-feedback teleoperation on low-cost arms and improves policy learning through Force-Informed Re-Sampling Training (FIRST), which up-samples pre-contact and contact segments during behavior cloning. Across five long-horizon tasks, FIRST outperforms prior force-aware policies by over 17% in task progress. Together, NEXT and FIRST bring force-aware teleoperation and policy learning to off-the-shelf robots without additional sensing hardware. Video results and code are available at https://jasonjzliu.com/factr2

Soft robots are valuable robophysical platforms for studying body-caudal undulatory locomotion, but their compliant bodies are difficult to control precisely under changing hydrodynamic loading. Conventional proportional-integral-derivative (PID) feedback stabilizes periodic undulation in static water, but can accumulate flow-dependent tracking delay and increasing inter-trial variability when environmental flow becomes non-trivial. Here, we evaluate whether augmenting PID control with a Linear Repetitive Learning Estimation Scheme (PID-LRLES) recovers tracking accuracy and repeatability under dynamic flow. The LRLES generalizes classical integral action from constant to periodic, non-constant references, while using a stable transfer-function realization whose poles have negative real parts to avoid the long-term instability issues of classical repetitive control. Closed-loop experiments were carried out in a recirculating flow tank at five bulk flow speeds spanning 0 to 32.6 cm s^-1, using an embedded soft capacitive bending sensor at a 1 kHz control-loop rate. With controller gains tuned once in static water and then held fixed across all conditions, PID-LRLES tracked the periodic bending-envelope reference more closely than the PID baseline and significantly reduced the inter-trial spread of the per-trial RMSE (paired Wilcoxon signed-rank test, p = 1.8 x 10^-4, n = 25). Embedded soft proprioception and cycle-to-cycle learning act as complementary contributors to robustness: the sensor exposes the periodic hydrodynamic bias in body deformation, while the learning term absorbs it over recent oscillation cycles. By reducing flow-dependent control-induced variability, the approach provides an enabling layer for future robophysical studies seeking to isolate the effects of morphology, sensing, and environmental flow on aquatic locomotion.

In this paper, we introduce the Soft Lamprey-Inspired Dual Environment Robot (SLIDER) and a proper modeling and optimization procedure employed to design the robot. We represent the primary fluid environment actions - inertial effects, vortex forces, and viscous dissipation - using Lighthill's theory for large-amplitude elongated bodies. For structural design parameters such as internal pressure, tail size, and body stiffness, a fast, geometrically and materially nonlinear model is developed and validated. The fluid-structure interaction equations are solved implicitly with an efficient second-order box method. A pneumatic manifold robotic system is employed to actuate SLIDER in a quiescent water tank environment, allowing cross-comparison of computational and experimental results. We find that low-frequency swimming is dominated by resistant environmental forces, whereas higher-frequency swimming is primarily affected by inertial fluid forces. Using our efficient model alongside a genetic algorithm, we co-optimize a swimming control pattern and caudal fin design (subject to SLIDER's climbing morphology) to achieve a tethered swimming speed of 21.7 +/- 0.4 cm/s (0.59 Bl/s). Furthermore, we investigate the optimization procedure for a multimodal robot performing both swimming and climbing tasks.