Robotic Arms

Aerial manipulators represent the forefront of aerial robotics. Although potentially capable of complex interaction tasks, controlling aerial manipulators throughout the dynamic transitions occurring during task execution presents significant challenges. Abrupt or discontinuous changes in system dynamics generated by the transitions suggest the use of a switched approach, yet the available aerial manipulation methods are not designed for coping with switched regimes. In addition, most available methods fall short in coping with the tight couplings between the aerial vehicle and the manipulator, as well as in coping with the state-dependent uncertainties arising from the difficulty in modeling such couplings. We propose a switched-based adaptive control framework for aerial manipulators not relying on a priori knowledge of the vehicle-manipulator couplings and of state-dependent uncertainties. To guarantee stable manipulation despite changes in system dynamics, the framework provides a class of switching signals characterizing those transition phases for which the system is guaranteed to remain stable. Comparative experiments further validate the effectiveness of the proposed switched-based framework over the state of the art.

Unlike conventional rigid-link robots defined by discrete joints, continuum robots pose a fundamental challenge for expressing their complex continuous bending configurations for closed-loop control. Several modelling approaches have been proposed for conventional continuum robots, but tensegrity-based continuum robots remain largely open. Moreover, many of these approaches assume a continuous elastic backbone and are therefore not directly applicable to tensegrity manipulators, whose bodies are networks of rigid struts and tensioned cables. This work presents a reduced-order model for shape and posture control of a tensegrity-based continuum manipulator. The manipulator is modelled as a serially connected parallel-link mechanism. The proposed method is formulated as an optimization problem that uses geometric constraints of the tensegrity structure together with information from the Inertial Measurement Unit (IMU) sensors embedded in the strut elements. To the best of our knowledge, this work presents the first experimental demonstration of a real-time IMU-based shape estimation method on a full-scale tensegrity manipulator and demonstrates posture control using a simple Proportional-Integral (PI) controller. The results show that the proposed method can estimate the shape of both single-module tensegrity structures and multi-module tensegrity manipulators from arbitrary static configurations and achieve desired postures.

Safety and comfort in human-robot physical in-teractions are essential aspects in the development of social technologies, where natural gestures, such as handshakes, represent a challenge due to their direct physical contact. The implementation of series elastic actuators (SEA) to absorb impacts is proposed as a design strategy that favors safer interactions. This paper presents an experimental study aimed at evaluating how the incorporation of SEAs in robotic arms influences perceived safety and the interaction experience dur-ing handshaking. The design allows a direct comparison of the effect of rigidity versus the incorporation of elastic elements, in order to identify the advantages of SEAs in improving the physical safety and social acceptance of robotic systems in everyday contexts. The experiment was carried out with 10 volunteers (6 men and 4 women), who performed two interactions with each robotic arm: one with rigid joints and the other with flexible joints using SEA. During testing, objective data on end-effector trajectories were collected, as well as subjective information through a perception survey focused on safety, naturalness, and confidence during the handshake. The survey results show increased perceptions of safety and comfort with the SEA-equipped arm, supporting its potential to facilitate safer and more socially accepted human-robot interactions.

In recent years, aerial manipulation has attracted increasing attention as a key to expand the application of aerial robots. In this work, we focus on two major research directions for achieving versatile aerial manipulation: (i) acquiring high environmental adaptability using soft manipulators, and (ii) expanding the feasible wrench space by distributing thrusters along the manipulator. However, no aerial robot has simultaneously satisfied these two requirements. Therefore, in this paper, we propose a morphing rotor-distributed aerial robot with flexible continuum links that achieves both high shape adaptability and an expanded wrench space. The flexible continuum links function as soft manipulators, passively conforming to the shape of the environment, while the thrusters distributed along the continuum links expand the feasible thrust wrench space and enable the end-effector to exert large interaction forces. To realize the proposed robot, it is essential to suppress vibrations of the lightweight continuum links. Thus, we develop a composite leaf-spring structure that provides both high torsional and vertical stiffness, and vibration-suppressing control methods. Using these implementations, we demonstrate stable flight and a variety of aerial manipulation tasks. To the best of our knowledge, this is the first work to realize aerial manipulations using flexible links with an integrated thruster.

Self-motion manifold (SMM) characterizes the geometric structure of the infinite inverse kinematic solutions set of a redundant manipulator at a fixed end-effector pose, and its efficient recovery underpins feasible and global optimal motion planning. Existing methods such as null-space continuation and learning-based methods are formulated around the assumption that an SMM is a curve, and do not extend to higher redundancy orders. We instead adopt a probabilistic view: SMMs are the support of the conditional posterior over configurations given a target pose, so that recovering it reduces to sampling from a learned distribution and separating its disjoint components by clustering. The formulation is independent of the manifold dimension and requires no architectural change as the redundancy order grows. In this work, we demonstrate that our method can approximate 1-D SMMs with performance comparable to the latest null-space continuation and learning-based approach, and that it is the first method capable of approximating highly redundant 4-D SMMs in a 7R manipulator for position tasks. Project website: \href{https://github.com/accuracy-maker/high-dimenstional-self-motion-manifold-approximation}{https://github.com/accuracy-maker/high-dimenstional-self-motion-manifold-approximation}

Passive counterweights are simple gravity compensators, but a counterweight selected from a single pose is not generally optimal for the configurations and tasks a manipulator actually executes. This paper develops a task-distribution-aware synthesis framework in which the operating distribution $ρ(q)$ enters the design explicitly. For a counterweight moment $p=m_c r_c$ with gravity torque $-gpφ(q)$, the weighted mean-square residual gravity torque has the closed-form minimizer $p^*=E_ρ[τ_gφ]/(gE_ρ[φ^2])$. If payload gravity torque is affine in payload mass, the optimum is also affine: $p^*(m_p,ρ)=p_0^*(ρ)+m_pK_p(ρ)$. For fixed static moment, added counterweight inertia is $I_c=pr_c$ while mass is $m_c=p/r_c$, so mass-radius selection is underdetermined unless physical constraints are specified. A recovered three-link manipulator is used as a case study. At $r_c=0.20$ m, zero-payload equivalent optima are 0.672 kg for uniform joint-space operation, 0.683 kg for approximately uniform task-space operation, 0.713 kg for a representative pick-and-place family, and 0.952 kg for a high-gravity-biased distribution, a change of more than 40% caused solely by the operating distribution. Nondominated fronts show that preferred mass-radius pairs depend on declared engineering bounds. A rated-torque-referenced all-joint screen increases zero-payload feasible task-space coverage from 78.1% without compensation to 93.7% for the uniform-distribution design. A lumped point-mass trajectory study gives a provisional crossover from no counterweight at very aggressive motion to stronger compensation as motion slows. These actuator and dynamic results are engineering consequence studies rather than physical validation.

Magnetic levitation (MagLev) systems have great potential for application in high-mix, low-volume manufacturing due to their scalability and flexibility, enabling highly reconfigurable in-machine material flow. However, their manipulation capabilities remain largely unexploited, as current applications almost exclusively focus on transportation. To enable grasping and manipulation directly on MagLev systems without requiring additional costly handling equipment, such as industrial robot arms, we present the Gripper MagBot, a low-cost parallel 6-DoF manipulator with an integrated 1-DoF gripper that mechanically couples three MagLev movers. The Gripper MagBot supports two operating configurations: a default mode and a single-track mode, selectable depending on the required stability and workspace footprint. To reconfigure a machine, the MagBot can be autonomously dropped off and picked up using a docking station. We showcase pick-and-place examples in simulation, as well as with the real Gripper MagBot using our inverse kinematics controller. CAD files, assembly instructions, a component list, and videos are available at https://sites.google.com/view/gripper-magbot.

Closed kinematic chains complicate modular modeling by coupling active and passive coordinates through nonlinear closure constraints. This paper presents a Path-Assembled Closure Differential Mapping (PACDM) framework for modular closure resolution and kinematic reduction. Each closure element compares two ordered transformation paths with common endpoints, with their mismatch expressed through the logarithm on SE(3) and the corresponding Jacobian assembled from local transformation derivatives. Multi-path modules are constructed from a minimal set of pairwise closure elements, while rank-revealing analysis selects locally independent scalar constraints. A defect homotopy recovers closure-consistent passive coordinates from approximate estimates along a feasible and regular continuation path. At regular configurations, implicit differentiation yields the local active-to-passive differential mapping, which is subsequently used in a predictor-corrector continuation procedure for prescribed motion. The framework is evaluated on a seven-degree-of-freedom heavy-duty manipulator containing two-path and three-path closed-chain modules. Comparison with Simscape Multibody yields trajectory root-mean-square errors below 8.5 x 10^-10 rad, while predictor-corrector continuation is approximately 45.8 times faster than applying defect homotopy at every trajectory sample.

Surface coverage with task-redundant manipulators is challenging because each surface point may admit multiple inverse kinematics (IK) solutions, and configuration choices strongly affect motion quality. This paper extends the classical Spanning Tree Coverage (STC) method to redundant manipulators through offline and online Joint Spanning Tree Coverage (JSTC) algorithms. Offline JSTC samples multiple Inverse Kinematics (IK) solutions per grid cell and formulates the problem as a Generalized Minimum Spanning Tree (GMST), selecting one configuration per cell and tracing the resulting tree to obtain a non-revisiting coverage path. Online JSTC incrementally expands and backtracks a spanning tree with feasibility and cost evaluation while handling dynamic grid updates. Simulation results show that offline JSTC reduces computation time, reconfigurations, and joint motion compared to other methods, while online JSTC achieves fast per-step planning in dynamic scenarios.

Robots operating in physical environments make control decisions based on uncertain sensor measurements, which can lead to unsafe or suboptimal actions. Runtime monitors that check their behavior against safety specifications must represent this uncertainty soundly. Zonotopes are a widely used representation, but continuously incorporating new measurements grows their order unboundedly, so monitors must periodically apply an over-approximating reduction. The choice of the reduction method substantially affects the zonotope's precision, yet existing approaches typically utilize a fixed method throughout the run, even though the optimal choice depends on the current state. This paper presents a Predictive Zonotope Reduction (PZR) approach, which frames reducer selection as an optimal control problem and solves it using beam-search model predictive control. Policy distillation into a small neural policy further provides substantially higher execution speed than model predictive control while maintaining improved performance, enabling uncertainty-aware runtime monitoring on resource-constrained real-time systems. We implement our approach in the RLola runtime monitoring framework and evaluate it on a 5-degree-of-freedom robotic arm simulated in MuJoCo, with sensor uncertainty modeled according to ISO 5725. Experiments on a Raspberry Pi 5 show that dynamic reduction significantly lowers false-positive rates in monitoring compared with static reduction strategies.

This study proposes a novel Model Predictive Path Integral (MPPI)-based task-space control framework. The proposed framework explicitly solves rigid-body dynamics within a real-time MPC formulation and enforces safety constraints, enabling accurate motion and force control that yields compliant behaviors for safe and effective physical interaction of robotic manipulators in unstructured environments. By leveraging MPPI, the proposed framework efficiently handles nonlinear dynamics that are difficult to solve with conventional MPC approaches in real-time. Furthermore, we develop a torque-sampling-based control architecture that enables efficient exploitation of GPU-based parallelization, resulting in effective compliant and force-aware behaviors. As a result, the proposed framework achieves a solver update rate of over 166 Hz with a 0.18 s prediction horizon, and its performance is validated through real-world experiments on a 7-DoF manipulator.

A long-standing open problem in robot manipulator control is whether global regulation can be achieved by classical PID control. This paper provides an answer to this question for classical PID controllers with triple parameters (k_p,k_i,k_d) in R^3. We find and prove that for one-degree-of-freedom manipulators, the classical PID control guarantees global stability and asymptotic regulation under standard structural assumptions, and further derive explicit quantitative design conditions for the PID gains. However, for multi-degree-of-freedom cases, we can construct a robot manipulator satisfying the same structural assumptions for which no choice of PID gains (k_p,k_i,k_d) can achieve global asymptotic regulation. These results provide a fundamental understanding of the abovementioned open problem, revealing both the fundamental capability and intrinsic limitation of the classical PID control for robot manipulator dynamics.

Long-horizon multi-part object disassembly requires robots to compute feasible sequences of collision-free removal motions, even in the presence of tight, narrow escape corridors. To efficiently solve such disassembly problems, we propose Parallel Extraction for Long-Horizon Disassembly (PEEL), an algorithm which efficiently computes disassembly motions for object assemblies and feeds them to a robot manipulator for execution. PEEL uses sampling-based motion planning to compute single-object motions through the use of a scale-invariant sampling scheme, where the object scale is estimated in a burn-in phase and a subsequent directional sampler exploits the scale. This sampling scheme is integrated into a multi-arm bandit rapidly-exploring random tree (MAB-RRT) planner, which switches between different samplers depending on the reward signal received. Using MAB-RRT, the PEEL algorithm runs a batch of planners in parallel to obtain an ordered graph specifying the sequence in which object parts have to be removed. We show that MAB-RRT can efficiently solve single-part disassemblies with 100 percent success rate on 76 assemblies, and that it is robust to its parameters. By integrating MAB-RRT into PEEL, we solve four long-horizon disassembly problems using the Fetch manipulator robot involving 10 to 17 individual object parts.

Large Language Models (LLMs) have significantly revolutionized the modern society with numerous advanced interactions between humans and AI agents, whereas the usage of most large language models including ChatGPT are not friendly open-sourced and must require the users paying a lot for such AI services continuously. Therefore, deploying open-sourced large language models on local servers can be considered as an efficient approach to design and implement creative embodied AI algorithms with lower cost and more stable free usage. Inspired by this ordinary motivation, we originally propose and implement the "Socratic Models-ChatGLM", which is a well-performed algorithm for multi-modal interactive control of robotic arm based on offline large language models via the facile PyBullet platform, even presents extraordinary potential to address complicated text-image integrated multi-step long-horizon robotic manipulation tasks.

We present a MR safe, master-slave robot manipulator for abdominal interventions in the MRI chamber. A human operated 2+1-DoF master controller manipulator transmits motion and force to a 2+1-DoF slave manipulator via fluid transmission. Jointly, a digital master controller provides multimodal control capability beyond common split axis or mode switchable hybrid human-digital controller configurations found in previous studies. High input impedance, low-leakage, elastomeric fluid actuators are delegated to remote angulation control. Low-friction graphite piston cylinders are delegated to needle insertion axis remote actuation given the sub-newton force transparency and sub-millimeter motion transmission over bedside fluid piping lengths. The device enables real-time MRI guided interventions allowing manual, digital, hybrid, and collaborative control modes. Collaborative tasks such as assisted tissue penetration, fault-driven virtual fixture, and motion compensation through feedback control are presented in this paper. Preliminary MR scanner results demonstrate manipulator functional viability for an in-vivo pig experiment in bedside, manual control mode configuration.

Intuitive teleoperation interfaces are crucial for the safe and effective operation of robotic manipulators in challenging environments. In the nuclear industry, surface contact tasks such as swab sampling require precise path and force tracking, obstacle avoidance, and sustained operator attention, which conventional joystick interfaces struggle to support effectively. This study designs and evaluates a novel touchscreen teleoperation interface that maps continuous finger movements directly to robotic manipulator motions, provides finer velocity control, and integrates control with visualization, enabling more natural, precise, and intuitive surface interaction than conventional controllers. A comparative user study with 20 participants evaluated task performance and workload using the proposed touchscreen, a conventional joystick, and a single-click autonomous mode. Tasks simulated realistic surface manipulation using a Franka Emika Panda arm, remotely controlled from another country. Kinematic, physiological, and behavioral data were recorded to comprehensively assess task performance, cognitive load, and operator trust across each control condition. Participants completed teleoperation tasks more efficiently and accurately with the touchscreen interface, achieving a 53.5% reduction in completion time (median: 2.50 vs. 5.38 min), higher in-area coverage on the sinusoidal path (90.7% vs. 84.1%), and lower overshoot on both path geometries compared with the joystick. Cognitive load, quantified via NASA-TLX (0-100), decreased from joystick to touchscreen (mean TLX 52 to 43; -9 points, -17.3%) and was lowest under the autonomous one-click mode (31; -21 points vs. joystick, -40.4%; -12 vs. touchscreen, -27.9%). This research presents an easy-to-implement touchscreen interface that improves performance in teleoperated surface tasks while reducing cognitive load.

Robotic construction systems often treat the material system and the robot as separate design problems, locating intelligence primarily in hardware, sensing, motion planning, and control. This project instead investigates how geometric intelligence can be encoded within architected material systems to simultaneously address requirements for robotic grasping, self-alignment, reversible connection, structural performance, and three-dimensional aggregation. We introduce a self-aligning compound nested lattice module composed of conjoined cuboctahedral-octahedral units. The cuboctahedral features of the modules provide defined surfaces for robotic grasping and alignment, while the octahedral features incorporate screw-releasable snap-fit connectors and corresponding receptors. Additionally, we present a nested arrangement that enables interlocking aggregation along the x, y, and z axes. We demonstrate the system through furniture and architectural scale structures assembled using both a robotic arm and mobile assembler. The resulting configurations include seating, spanning structures, surfaces, and vertical frames. Compression testing of the compound module produced a stiffness of 4,556 N/mm, a maximum load of 3,445 N, and a compressive modulus of 17.5 MPa. The modules can also be disassembled and reused across different configurations, supporting reconfigurable and circular construction.

Model Predictive Path Integral (MPPI) control is widely used in manipulation for its gradient-free, parallel handling of non-convex costs. Manipulation tasks, however, often impose constraints that hold throughout the motion: a closed kinematic chain that two grasping arms keep exactly, or joint limits and obstacle clearances that are never crossed. MPPI handles such constraints only through the cost, as soft penalties that hold approximately and fail under a strong task cost. To address this, we propose Projection-Retraction MPPI (PR-MPPI), which enforces the constraints inside the sampled dynamics. At every rollout step, the sampled velocity is projected to satisfy both constraint types: the equality restricts it to a subspace, and each inequality to a half-space within that subspace, so inequality handling never breaks the equality. This projection, however, satisfies the constraints only to first order, and a finite step leaves a small drift off the equality. Therefore, we retract the returned command back onto the constraint to numerical tolerance and independent of task weighting. We validate PR-MPPI on 14-DoF dual-arm systems. In simulation, the returned commands satisfy the closed-chain equality to numerical tolerance through a joint-limit stress test and randomized obstacle avoidance. On real hardware, the arms of a Unitree H1-2 humanoid reactively avoid a moving obstacle. Code and experiment videos are available at https://rcilab.github.io/prmppi.

This research proposes a constrained motion planning framework for robot manipulators in human-robot interaction (HRI). For a non-redundant manipulator with a fully specified end-effector pose, additional requirements such as collision avoidance and self-collision avoidance are difficult to handle as simple null-space secondary tasks. This limitation makes it challenging to generate feasible joint-space trajectories in HRI environments where safety and kinematic constraints must be considered simultaneously. To address this limitation, collision- and self-collision-aware trajectories are generated using Rapidly-exploring Random Tree (RRT) and RRT* algorithms, and the resulting dataset is used to train a diffusion model that generates constraint-satisfying trajectories through guided sampling. To reduce the inference time required for iterative diffusion sampling, consistency distillation is applied, and a joint-weighted jerk regularization term is incorporated into the loss function to promote smoother trajectories by penalizing abrupt changes in joint acceleration. Simulation results show that the consistency model generates 150 trajectory candidates in less than 100 ms, maintains a high episode success rate, and substantially reduces joint and end-effector jerk when jerk regularization is applied.

We propose a workspace-fibered decomposition framework for motion planning in nR planar redundant manipulators operating in cluttered environments. Rather than planning directly in the full n-dimensional configuration space, the method incrementally constructs obstacle-constrained reachable workspaces of lower-dimensional non-redundant sub-chains and recursively lifts them through redundant orientation fibers. This yields a sequence of reduced planning manifolds that preserve branch-consistent reachability structure while avoiding explicit construction of the full configuration-space obstacle geometry. We first establish that, for planar position-only manipulators, the obstacle-constrained reachable workspace induced by the minimal non-redundant sub-chain provides an exact characterization of feasibility with respect to the connected component of the start configuration, enabling early infeasibility detection prior to introducing redundant degrees of freedom (DOF). We then introduce an incremental fiber-lifting procedure that propagates reachable workspace structure through successive redundant links while enforcing local inverse-kinematic branch consistency using Jacobian determinant continuity constraints. The resulting representation admits efficient reduced-space planning directly on recursively-constructed workspace-fiber manifolds. Experimental results on redundant nR planar manipulators demonstrate that the proposed construction preserves collision-free connectivity structure across successive lifting stages while substantially reducing collision checking complexity relative to direct configuration space reasoning.

Mainstream plan-then-track approaches to multifingered grasp execution entail selecting a grasp, planning a collision-free trajectory, and tracking the resulting trajectory via a feedback controller. Pose-estimation error during execution or scene motion can invalidate this open-loop commitment and trigger replanning. We thus present Grasp Distance Fields (GDFs), smooth softmin distances to finite sets of arm-hand grasp configurations. Using their negative gradients as feedback, we jointly select and execute grasps without planning a trajectory. A CBF-CLF quadratic program (QP) enforces self-collision, workspace, object, and obstacle-clearance constraints, while its CLF slack quantifies obstruction of task progress. We bound the softmin approximation error by $\log N/ρ$ and prove forward invariance of the filtered safe set. To handle changes in contact topology, we combine a hysteretic contact-mode transition with a wrench-quality CBF that limits degradation of the realized force-closure margin relative to hold onset. Using our method, a fixed-base manipulator and a Unitree G1 equipped with the same underactuated hand grasp and lift 46 of 50 test objects amid clutter and moving obstacles. The realized grasps also retain a median 94% of their synthesized quality margin, and each QP solve requires 0.09 ms within a 20 ms control interval. Project page: www.clintonenwerem.com/gdf.

Cable-Driven Parallel Robots (CDPRs) are a type of parallel mechanism in which cables are used as actuators. Due to the two levels of redundancy and numerous constraints within the CDPR actuation, joint and operational spaces (together known as the tri-space), tracking a given trajectory in the operational space while satisfying constraints in tri-space simultaneously is challenging. To the best of the authors' knowledge, there does not exist any tri-space control framework, which is robust, effective, and directly applicable to several architectures of redundantly actuated CDPRs. This paper proposes a tri-space control framework that combines Reactive Control (RC) and Iterative-Learning Control (ILC) to perform repetitive tasks in the operational space. The framework allows the tracking of operational space trajectories online with feasible cable forces, while avoiding undesirable situations such as cable-link interference, joint interference, and loss of manipulability. On the other hand, by finding an optimal parameter in the null space using a novel parameterization of a null space vector, the performance can be improved through ILC when the task is repeatedly executed. Simulation and hardware results on various Multilink Cable-Driven Robot (MCDRs) and Hybrid Cable-Driven Robots (HCDRs) show that the proposed tri-space control framework can be conveniently and effectively applied to the real-time control of different CDPRs.

Cable-driven manipulators exhibit strong nonlinearities and low structural stiffness, which make precise control challenging under time-varying uncertainties and external disturbances. This paper presents a time-delay-estimation (TDE)-based adaptive fractional-order nonsingular terminal sliding mode (AFONTSM) control strategy for cable-driven robots. A robust controller is constructed within a TDE-based model-free framework by combining fractional-order nonsingular terminal sliding mode error dynamics with a fast terminal sliding mode reaching law. The main contribution is a new adaptive law that introduces an adaptive exponential term into the update gain to form a nonlinear adaptive mechanism. This design improves adaptive regulation under different operating conditions by suppressing noise-induced chattering during smooth tracking while preserving or enhancing the adaptive gain during trajectory reversal. Lyapunov analysis proves the ultimate uniform boundedness of the tracking error. Experimental results show that, compared with the baseline method, the proposed controller reduces RMSE by 34.52% and 31.11%, ITAE by 33.79% and 32.97%, and ISCT by 6.69% and 17.77% for the two joints, respectively. Further comparisons with recently reported adaptive laws demonstrate that the proposed law provides faster adaptive response, more stable gain evolution, and improved chattering suppression. Additional payload tests further verify the robustness and repeatability of the proposed method.

Many ceiling construction tasks still rely on heavy serial manipulators that are difficult to deploy in cluttered interiors, motivating lightweight, field-ready alternatives that reach ceiling height while maintaining millimeter-level accuracy and the stiffness demanded by overhead tool loads. We introduce Tripody, a wheeled 3-DoF parallel robot for high-reach tasks that replaces the base spherical joints of a classical 3-SPR (3 legs; S: base spherical joint; P: actuated prismatic joint; R: end-effector revolute joint) morphology with universal joints, intentionally overconstraining the mechanism; small, distributed elastic deflections absorb the resulting incompatibilities, preserving predominantly translational motion. The 33kg system extends from 1.7m to 3.4m in height, supports a continuous 32kg payload, and offers a modular end-effector interface for ceiling operations. We detail the mechanical design - including custom linear actuators and a kinematic-compatibility analysis - and a control stack for accurate positioning that combines SE(3) state estimation, forward kinematics, and task-space control. In experiments, Tripody exhibits similar in-plane stiffness to a spherical-base variant but substantially higher torsional stiffness - an increase of 67% at 1.7m, 196% at 2.6m, and 454% at 3.4m - while maintaining negligible cross-axis coupling. Closed-loop positioning with a total station converges below 0.6mm across the entire workspace; pure model extrapolation achieves a 95th-percentile error of 2.7mm (max 3.6mm). Finally, we demonstrate task-level ceiling-drilling feasibility in an open-loop study by drilling a 15-hole pattern with 4.5mm maximum relative hole-position error after rigid alignment. These results support overconstrained, compliance-absorbing 3-SPR-like architectures as a practical path to lightweight, high- reach, millimeter-accurate construction robots.

Safety inflation can cause nearby obstacles to overlap, violating the disjoint-obstacle assumptions used by many modulation-based reactive planners. We investigate Star-World workspace reshaping for three-dimensional reactive control of a Franka Emika Panda manipulator. At each update, intersecting inflated obstacles are clustered and replaced by star-shaped proxies before a dynamical-system-based end-effector controller is evaluated. A null-space artificial-potential-field term provides complementary arm-body avoidance. We compare reshaped and unreshaped obstacle representations in six PyBullet scenarios using goal attainment, path-length ratio, and computation time. In this preliminary 12-trial evaluation, reshaping reaches the goal in five of six scenarios, compared with four of six for the unreshaped baseline. It resolves the canonical overlapping-wall case and requires 0.68--8.70,ms per workspace update for scenes containing one to seven obstacles. However, it also increases path length, produces near-equilibria in two cases, and closes a navigable corridor through over-aggressive merging. These results show both the promise and the practical limitations of transferring Star-World guarantees from workspace geometry to a redundant manipulator controlled through inverse kinematics.

The paper proposes a robot-agnostic compliant-control framework that extends the ROS control ecosystem with standardized joint and Cartesian command interfaces. It addresses a key limitation of existing control software: no reusable infrastructure for implementing compliant-control algorithms across different manipulators while preserving a common interface to higher-level applications. A plugin-based architecture separates controller infrastructure from control-law implementation. Generic wrappers use existing hardware abstractions to interface with different manipulators, while runtime-loaded plugins implement only the control law. Command interfaces support joint- and Cartesian-space references, stiffness and damping gains, nullspace targets, and feedforward terms, enabling variable impedance and diverse compliant-control formulations. Robot kinematics and dynamics are computed from URDF models using Pinocchio. The architecture facilitates the development of compliant-control strategies and enables the same implementation to be deployed across platforms unchanged. The complete framework, including reference controllers, high-level task interfaces, and example configurations for various manipulators, is open-sourced. The reference Cartesian impedance controller supports task-dependent compliance by rotating translational and rotational stiffness and damping, allowing the principal compliance directions to be updated online according to local task geometry rather than remaining fixed in the robot base or TCP frame. This is particularly important in contact-rich manipulation, where the desired directions of motion, constraints, and compliance directions may vary throughout task execution. Real-robot experiments demonstrate task-dependent compliance in contact-rich manipulation, while simulations show portability across manipulators with distinct kinematic and dynamic characteristics.

Nociception is a protective biological mechanism that links harmful stimulation to a reaction. This paper investigates artificial nociception for a robotic arm with whole-body tactile sensing. We present a complete pipeline that maps pressure changes from sensitive skin on a robot manipulator to bio-inspired withdrawal motions. The system first converts skin pressure into a scalar pain gain using a nonlinear continuous model. We compare three reflexes: (i) uniform reflex moves four robot joints by a fixed amount, whereby the withdrawal is approximated by a movement of the arm "toward the base", independent of where the robot was touched; (ii) biologically motivated location-dependent joint-space withdrawal derived from human withdrawal reflex characteristics; (iii) Cartesian space withdrawal along the surface normal of the contacted skin pad. All behaviors are integrated in a reflex controller that interrupts the task, executes the withdrawal, and returns to a pre-contact pose. A user study with 15 participants compared the strategies using Godspeed questionnaire subscales, custom perceived-naturalness and safety items, forced-choice comparisons, and qualitative feedback. Interestingly, participants rated more highly the uniform reflex behavior over one or both competitors on the anthropomorphism, animacy, and likeability Godspeed subscales and on the Naturalness and Realism custom scale. When asked to compare the conditions, the uniform reflex was scored best in "felt safest", "most human-like", and "most natural". This suggests that predictability of the robot behavior is key for user acceptance. The Cartesian reflex was judged the most appropriate reaction to touch. The bio-inspired reflex did not lead any evaluated measure. This may be partly attributed to the embodiment gap between the robot arm and human arm and participants having different expectations from a robot manipulator.

Learned manipulation policies increasingly predict motions for abstract "hands" and are attractive in practice because they rely on easily collected demonstrations and transfer across robot platforms. Executing these trajectories on multi-arm robots, however, is not trivial. Multi-hand policy outputs must be assigned to physical arms, each arm must realize a configuration-space motion that tracks its prescribed end-effector trajectory, and all arms must respect kinematic limits and avoid collisions. In the absence of algorithms that directly address this problem, practitioners typically extend single-arm inverse-kinematics (IK) pipelines in an ad hoc way, with no guarantees of feasibility or safety. In this work, we close this execution gap with a search-based framework that is theoretically complete for grounding policy-generated multi-hand trajectories onto physical multi-arm systems. Building on Conflict-Based Search, our method explicitly searches over both the discrete assignment of trajectories to arms and the continuous Jacobian null spaces of redundant manipulators, using redundancy to avoid inter-arm collisions while tracking the prescribed motions. This unified treatment of assignment and null-space motion yields a practically efficient planner that safely realizes coordinated manipulation-policy outputs on multi-arm robots. See omcbsa.github.io for more.

We provide a novel end-to-end framework for the execution of an assembly operation by two robotic arms, given the digital CAD models of the parts and their desired relative placement in their assembled state. We analyze and demonstrate the advantages of using two robotic arms simultaneously in tight assembly operations, compared to single-arm systems. Our method is implemented in both simulation and using physical robots. It provides theoretical guarantees on execution time and trajectory accuracy, supported by empirical evidence. In particular, we show that coordinated movement of two arms reduces average execution time by more than 50% compared to using a single arm only, produces higher-quality trajectories, and accelerates the search for valid robot placements. Furthermore, we establish bounds on the required dimensions of the robotic cell. Our open source software together with real-life video demonstrations are available in our project page.

Efficient, collision-free, and time-optimal motion planning is a fundamental requirement for autonomous forestry cranes operating under hydraulic pump-flow constraints. The Via-Point-based Stochastic Trajectory Optimization (VP-STO) algorithm has demonstrated near-time-optimal hybrid motion planning in this domain, but requires a fixed terminal joint configuration specified prior to optimization. For kinematically redundant manipulators such as forestry cranes, this pre-commitment to a single inverse kinematics solution restricts the planner's ability to exploit redundancy, particularly under the nonlinear, globally coupled pump-flow constraint where admissible joint velocities depend on their combined hydraulic demand. This paper presents TSC-VP-STO, a task-space-constrained extension of VP-STO that replaces the strict terminal joint-space constraint with a task-space constraint, jointly optimizing the trajectory and the redundant degrees of freedom of the terminal configuration. This enables the planner to adapt end configurations to the environment-dependent motion and hydraulic flow allocation, yielding more balanced pump utilization and shorter trajectory durations. We formalize the approach through a configuration space decomposition and derive a concrete reachability constraint for the forestry crane kinematics. Experimental evaluations across multiple planning targets and via-point configurations demonstrates a reduction on trajectory durations by 12-15% on average and improved pump-flow utilization compared to the baseline VP-STO. The practical applicability of TSC-VP-STO is validated through real-world deployment on a forestry crane, including a full log-loading cycle.

Deep reinforcement learning (DRL) has a longstanding tradition in addressing the reach-avoid task problem, especially for controlling robotic arms. While this task serves as a baseline environment within the research community, the ability of DRL to effectively learn the each-avoid task in complex and realistic scenarios beyond simplified and restricted tabletop settings remains uncertain. In this paper, we present, for the first time, a comprehensive benchmark for the reachavoid task that accurately captures real-world complexities without simplifications. We demonstrate a diverse range of settings for robotic arm reach-avoid task, which can be used for evaluating DRL research. We achieved this by utilizing the MuJoCo MJX physics engine and parallelizing both the simulation environment and DRL algorithms using the Brax library. We achieved state-of-the-art results with success rates of 96.1% (UR5e) and 98.8% (Franka Emika Robot) for the reach task and 86.8% (UR5e) and 95.2% (Franka) for the static reachavoid task. Our results indicate that while in previous works DRL agents could solve, for example, a reach task in a simplified setting perfectly, their agents performance collapses when evaluated in realistic scenarios. Overall, this work identifies that additional research is still required to claim the successful resolution of the robotic arm reach-avoid task using DRL. The environment and benchmarking code is available as open source at the following link

Soft continuum robots require embedded sensing for proprioception and contact detection, yet integrating sensors into sparse, highly deformable architected structures remains challenging. We present a model-based strategy that decouples proprioceptive and contact signals from a common set of fluidic pressure sensors embedded in a soft architected segment. Each segment of the Innervated Trimmed Helicoid (ITH) contains six air channels routed in a localized zigzag pattern along the circumference. With only three principal kinematic degrees of freedom (axial compression, bending in x, bending in y), the six pressure readings form an overdetermined system. A piecewise constant curvature model maps pressures to shape, and Huber regression identifies outlier channels whose residuals indicate external contact. On a single ITH segment, this approach achieves proprioceptive shape estimation with a relative bending error of 0.11 +/- 0.02 and a contact detection rate of 97% across 178 trials. We integrate eight ITH segments into Air-Helix, a tendon-driven soft continuum manipulator, and present exploratory whole-arm demonstrations that include tactile teaching by demonstration, admittance-controlled force regulation, and tactile object reconstruction. The results suggest that localized fluidic innervation combined with model-based redundancy resolution is a practical path toward concurrent proprioception and contact sensing in architected soft robots.

Model-based control of flexible joint robots with position-controlled actuators relies on accurate knowledge of the joint compliance. In practice, precise stiffness models are often unavailable as the properties of physical elastic elements vary with operating conditions and slowly change over time due to wear and aging. To improve model-based control of these systems, we propose an adaptive control approach in this work, which updates an estimate of the uncertain, nonlinear torque-deflection relation of each joint. As opposed to classical adaptive control approaches for non-elastic robots, we rely on an implicit control law and a control-input-dependent regressor matrix to account for the uncertain joint stiffness. We analyze robustness of the approach against errors induced by the motor position controller. Experimental results on a flexible joint with nonlinear stiffness characteristics demonstrate the effectiveness of the proposed approach.

Collisions of rigid-link robots and rigid environments are often modeled as instantaneous events. Under this idealization, the impact forces become impulsive and the system velocities nonsmooth. In this work, we systematically analyze pre- and post-impact velocities focusing on what we refer to as the nonsmooth impact direction (NSID). We show that it is a characteristic direction of a robotic impact and largely independent of contact properties. The results are directly applicable to large classes of backdrivable robotic systems with rigid links. We address particularities of systems with nonelastic and flexible joints, unconstrained as well as constrained systems. Further, we show that the approach direction w.r.t the NSID sets the direction of the impulsive force in frictional, inelastic impacts. The comprehensive theoretical analysis of this work supported by an experimental validation may serve as a foundation for future planning and control algorithms for various robotic impact applications. These can include humanoid locomotion on a slippery surface or repetitive hammering.

Multi-robot-arm motion planning is a key challenge in deploying multiple manipulators for industrial tasks such as manufacturing. Existing search-based and sampling-based solvers often require significant computation time to produce collision-free, high-quality motions suitable for safe real-world execution. In this work, we introduce a new suite of multi-robot-arm motion planners capable of near real-time motion generation, combining classical planning algorithms with state-of-the-art vectorized collision-checking techniques. Based on CPU SIMD instructions, our new planners accelerate their primary bottleneck, collision checking, and achieve up to two orders of magnitude speedup in both motion planning and execution postprocessing for multi-arm manipulation tasks. We also release our implementation to lower the barrier for research and development of multi-robot-arm planning and manipulation problems. Code is available at https://vamp-mr.github.io/vamp-mr

Spacecraft attitude control is traditionally achieved using momentum exchange devices or propellant-consuming thrusters. Meanwhile, a growing number of missions require robotic manipulators, which are typically treated as disturbance sources to be rejected rather than as actuators for spacecraft reorientation. This work investigates the use of manipulator motions for propellant-free attitude control by formulating a trajectory optimization problem with critical joint and collision avoidance constraints. Using an interior point solver for the resulting nonlinear program, complex slew and detumble trajectories are demonstrated for a range of spacecraft-manipulator systems with varying kinematic complexity and mass properties. The achievable control authority is compared directly with that of reaction wheel arrays via momentum and torque envelopes, demonstrating the potential for manipulators to serve as redundant or even primary attitude control systems. This work provides a framework for using manipulators as multipurpose attitude control actuators, with particularly promising applications in in-space assembly and manufacturing when grasping payloads with high relative mass fractions.

We propose an algorithm and its implementation for trajectory planning and certification for 3-DOF robot manipulators. The method uses Real Quantifier Elimination (QE) based on Comprehensive Gröbner Systems (CGS), also known as the CGS-QE method. The main advantage of the proposed method is its efficiency in trajectory planning and solution certification. This efficiency comes from the effective use of the CGS. First, for trajectory planning, we solve the inverse kinematics problem at each point along the trajectory via Gröbner basis computation. This usually requires recalculating the Gröbner basis at every point, which is time-consuming. We avoid this by computing the CGS for a parametric system. Here, the end-effector coordinates are parameters. This approach streamlines the algorithm. Second, for solution certification, the CGS-QE method certifies that an inverse kinematics solution exists at any point along the end-effector's trajectory. Our method also certifies solutions for trajectories composed of line segments and cubic natural splines. The algorithm is implemented within the computer algebra system Risa/Asir.

We aim to address the challenge of teleoperating robotic arms for high-degree-of-freedom (high-DoF) manipulation tasks, which is cognitively demanding and error-prone, particularly when relying on low-bandwidth interfaces. We propose Robot Trajectron V3 (RT-V3), a probabilistic shared control framework designed for $SE(3)$ grasping tasks. RT-V3 formulates shared control as Bayesian inference by learning a prior over user intent and combining it with real-time user commands to estimate the posterior intent distribution. The prior models user intent as a distribution over future trajectories conditioned on past robot dynamics and visual scene context. The intent prior is parameterized by a transformer-based conditional generative model that reasons over point clouds and candidate grasp poses, together with a factorized translation-rotation representation that improves learning efficiency in high-dimensional action spaces. During execution, RT-V3 continuously estimates the posterior distribution over future trajectories by combining the learned intent prior with a user-command likelihood derived from the observed control input, enabling continuous intent refinement and shared assistance. Comprehensive experiments demonstrate that RT-V3 achieves high accuracy in trajectory prediction and competitive performance in reactive planning. Furthermore, real-world user studies indicate that RT-V3 significantly outperforms baseline methods in terms of success rate and efficiency, while substantially reducing the user's physical and mental workload.

Trajectory planning strongly influences tracking accuracy, actuator demand, and overall execution behavior in robotic manipulators. Classical planners such as cubic, quintic, and trapezoidal profiles are widely used for their simplicity and smoothness, yet they remain purely kinematic and ignore system dynamics and control effort during trajectory generation. As a result, nominally smooth trajectories can lead to inefficient nonlinear execution and increased corrective control action. This paper presents a control-aware optimal trajectory planning framework that explicitly incorporates manipulator dynamics and actuator effort within a finite-horizon formulation. A midpoint linearization strategy is introduced to improve approximation accuracy for large point-to-point motions. In contrast to prior comparisons, the proposed approach enables fair, isolated evaluation of trajectory generation effects under identical closed-loop nonlinear execution conditions. To this end, a unified evaluation framework is developed in which all planners are executed under identical nonlinear dynamics, controller structure, and actuator constraints. Simulations on a nonlinear simplified UR5 manipulator show that the proposed approach consistently reduces tracking error, corrective torque, and closed-loop execution cost compared to classical methods, achieving substantial reductions in actuator effort and execution cost across all evaluated scenarios, demonstrating that kinematic smoothness alone does not ensure dynamically efficient execution.

Employing multiple manipulators can boost efficiency and accomplish tasks that a single manipulator cannot do. However, real-time planning for multiple manipulators in a cluttered workspace still poses significant challenges for planning algorithms. This article proposes a new planning algorithm called Conflict-Based Lazy Search (CBLS) for multimanipulator planning. CBLS is built on Conflict-Based Search (CBS), an efficient multiagent pathfinding (MAPF) algorithm that has shown an order of magnitude speedup over previous approaches [1], [2]. CBS addresses MAPF by solving many single-agent pathfinding (SAPF) problems. Thus, its planning time directly depends on the efficiency of the SAPF algorithm adopted. Our CBLS algorithm enhances CBS with precomputation and lazy search. First, a lazily evaluated graph with controlled sparsity is precomputed for a single manipulator. Second, we propose the Lazy Edged-based A* (LEA*) for efficient SAPF. Since edge evaluation is the computational bottleneck of manipulator planning, LEA* uses lazy search and an edge queue to reduce the number of edge evaluations. We show that LEA* is optimally vertex efficient and has improved edge efficiency compared to A*. We apply the proposed CBLS to multi-manipulator planning problems and show its superior performance by comparing it with CBS and a sampling-based algorithm, namely, RRT-Connect.

Continuum manipulators mounted on multi-rotor UAVs enable compliant aerial manipulation, but payloads and propeller downwash amplify out-of-plane bending and twisting that degrade end-effector pose accuracy. To address this problem, we present a universal-joint-based continuum manipulator designed to improve resistance to out-of-plane deformation during aerial manipulation. The proposed design uses a tubular backbone with spring-reinforced universal joints and an integrated conduit for internal routing and fluid delivery. We evaluate the design in still air and under peak propeller downwash across varying payloads, and benchmark it against a prior Nitinol-backbone CM. Bench tests show improved resistance to out-of-plane deformation across all conditions. Under peak downwash, the proposed design reduces mean error by 2.5-4x in yaw, 2-45x in y-axis, and up to 5x in roll compared to the NiTi-backbone design. We further analyze hover stability through in-flight coupled-disturbance tests over varying payloads and actuation speeds, and demonstrate the system in water sampling, spot spraying, and object transport.

Infrastructure maintenance, contact-based inspection, and emergency response can benefit from aerial vehicles that act as a flying human hand with extreme maneuverability, manipulation, and resiliency (MMR): maneuverability to fly in arbitrary orientations to reach remote and tight locations; manipulation to point sensors, turn valves, and press tools at arbitrary orientations; resiliency to maintain accurate motion and force control despite disturbances from arbitrary directions, such as wind, ground effects, and friction. Realizing MMR on aerial vehicles requires not only omnidirectional flight; it also requires (I) vectoring of maximum thrust in any direction, to maximize capacity for contact-force application and disturbance rejection, (II) global stability, to enable control over any orientation/position, and (III) compact, standard designs that build upon platforms such as quadrotors to inherit technological know-how. No current aerial vehicle simultaneously enables I--III, due to structural and control limitations that constrain actuation. We present MorphQuad: a morphable quadrotor that enjoys MMR. Key to our approach is a hardware and control co-design: on hardware, we independently articulate each of the four rotor systems via two-axis gimbals; on control, we introduce globally-stable control, and energy-optimal thrust allocation that permits inter-rotor thrust cancellations only to avoid downwash interference and gimbal lock. With fully-onboard autonomy, MorphQuad demonstrates multi-revolution rotation while translating or hovering, for pipe inspection and target tracking (maneuverability); valve turning, perching, and object pressing and pushing with human-level strengths (manipulation); and wind rejection from any direction, even directed to a single rotor, and push-pull recovery (resiliency).

This paper presents an intelligent control framework for trajectory tracking of robotic manipulators using radial basis function (RBF) neural networks for online disturbance estimation. The proposed control structure combines model-based nonlinear control with an adaptive neural approximator that compensates for parametric uncertainties, friction, and unmodeled dynamics. A Lyapunov-based adaptation law with projection guarantees boundedness of the closed-loop signals and convergence of the tracking error to a compact region. The primary objective of this work is to investigate how the choice of activation function within the RBF network influences transient behavior, steady-state accuracy, and control smoothness. The controller is implemented on a robotic manipulator. Experimental results demonstrate that although stability is preserved for all kernels, activation function selection significantly affects adaptation dynamics and practical tracking performance. These findings demonstrate that activation function selection acts as a structural design parameter in intelligent control, directly shaping adaptation dynamics and practical closed-loop performance.

We present STT-LfD, a unified Learning from Demonstration (LfD) framework that integrates motion learning with control for unknown Euler-Lagrange systems. Unlike traditional decoupled approaches that track a fixed reference, the proposed method treats demonstrations as a data-driven safety specification. Using heteroscedastic Gaussian Processes, STT-LfD learns Spatiotemporal Tubes (STTs) as an intent envelope that capture time-varying precision requirements of a task. A closed-form feedback controller then enforces these learned constraints while respecting actuator limits, without requiring explicit system identification. The approach preserves the temporal structure of demonstrations, remains computationally efficient, and avoids explicit system identification. Hardware experiments on a mobile robot and a 7-DOF manipulator show that it outperforms baselines in robustness to disturbances and computational speed.

Redundant robotic manipulators operating in constrained and human-interactive environments require accurate task-space tracking together with rigorous safety guarantees under dynamic uncertainties. Classical operational space computed torque controller (OSCTC) relies on accurate dynamic models and degrades in the presence of disturbances. In contrast, the data-driven paradigm of residual learning approximates disturbances as functions learned from full-state measurements, which are often noisy in practice, lack rigorous theoretical guarantees, and introduce additional design complexity. This paper proposes a robust OSCTC framework that integrates an extended state observer (ESO) with conformal prediction to combine model-based robustness and data-driven adaptability. The ESO estimates lumped disturbances directly in operational space without requiring full-state measurements as in residual learning, and a robust control barrier function (CBF) is constructed to enforce safety under uncertainty. However, robust CBFs require a known disturbance-variation bound to guarantee absolute safety, which often leads to conservatism in practice. To address this limitation, we further employ a sliding-window conformal prediction mechanism to estimate the bound online in a distribution-free manner, thereby achieving practical probabilistic safety guarantees. Experiments on a 7-DoF Franka Research 3 manipulator demonstrate millimeter-level tracking accuracy and real-time safe control at 1~kHz under various disturbances.

Robots deployed in safety-critical environments must execute motions that are simultaneously robust to disturbances and provably safe from collisions. Dynamic Movement Primitives (DMPs) offer inherent stability, temporal flexibility, and efficient trajectory generalization from single demonstrations, but they lack formal safety certificates. Conversely, Hamilton-Jacobi (HJ) Reachability analysis provides a principled framework for computing worst-case safety margins and forward-invariant safe sets, but classical grid-based methods suffer from the curse of dimensionality and are impractical for real-time control. This paper introduces HJ-SafeDMP, a framework that integrates DMPs with learned HJ Reachability-based safety value functions to achieve provably safe, robust, and computationally efficient robot motion. We learn a Control Barrier Value Function (CBVF) from offline demonstration data using a model-free, finite-difference HJ recursion and deploy it as a real-time safety filter via a closed-form control law that modulates the DMP output. Unlike optimization-based CBF-QP approaches, our method achieves safety filtering without online quadratic program solves, preserving the computational efficiency of DMPs. We further incorporate an expectile-based offline learning objective that avoids querying out-of-distribution actions, and a conformal prediction calibration step that provides finite-sample probabilistic safety coverage. Experimental evaluation on a 7-DOF robot manipulator demonstrates that HJ-SafeDMP achieves formal safety guarantees with orders-of-magnitude faster execution than optimization-based baselines, while maintaining the robustness and adaptability of DMPs for human-robot interaction.

Motion feasibility prediction plays a central role in robotics, particularly in task and motion planning and manipulation. A major bottleneck for this problem in cluttered environments is that infeasible planning attempts by Sampling-based motion planners (SBMPs) can incur substantial computational cost. Also existing approaches for infeasibility certification are limited to low-dimensional configuration spaces and often assume simplified geometric environments represented by primitive objects with known parameters. We study the complementary problem of learning motion feasibility prediction directly from raw RGB-D observations for a 7-DOF manipulator operating in realistic cluttered scenes. We introduce the first large-scale benchmark for this setting, comprising 2.7M grasp feasibility labels over 88 scanned objects and 190 cluttered tabletop scenes. We benchmark three representative classifier families spanning MLP- based, volumetric-CNN, and point-cloud-based Transformer architectures under matched training conditions. Our best model, GRASPFC-PTX (a point-cloud transformer), achieves an AUROC of 0.996 on Novel objects while providing predictions significantly faster than SBMPs.

Robotic manipulators operating in unstructured environments face significant challenges in safely executing goal-directed tasks due to dynamic and unforeseen obstacles, while traditional methods rely on prior knowledge or fixed perception pipelines, limiting adaptability. We propose a framework for safe task execution with effective obstacle avoidance. The environment module performs real-time obstacle detection, 3D localization, and ground surface geometry estimation. It then generates a structured semantic report that includes obstacle positions, object geometry and shape, and whether obstacles lie inside, outside, or within critical interaction zones. A central coordination module manages the overall system by handling tool invocation (e.g., memory and MoveIt collision scene updates), facilitating communication between modules, and continuously monitoring task progress until completion. Furthermore, a planning module selects an appropriate motion planning algorithm, such as RRTConnect, RRT*, or BiTRRT, based on the current environment configuration and goal requirements. The trajectory generated by the planner is further analyzed and refined to ensure safe and collision-free task execution. The proposed approach is evaluated in Gazebo Classic , demonstrating robustness in dynamic scenarios.

Legged manipulators combine the mobility of legged platforms with the manipulation capability of robotic arms. However, arm-induced Center-of-Mass shifts and dynamic disturbances make the system more prone to instability under actuator failures, potentially leading to falls, task failures, or safety risks. Existing fault-tolerant control methods mainly focus on locomotion alone, leaving the coupled problem of whole-body stability and arm reachability in fault-tolerant loco-manipulation largely unaddressed. To bridge this gap, we propose FT-WBC, a fault-tolerant loco-manipulation framework for robust whole-body control of legged manipulators under actuator failures. FT-WBC adopts a decoupled upper- and lower-body policy architecture and introduces two key modules: a Fault Estimator (FE) and a Posture Adaptation Module (PAM). The FE predicts faulty joints from lower-body proprioceptive histories, while the PAM uses this fault information to adapt the base posture plan generated by the arm policy, converting potentially unstable posture requests into safe and executable base posture commands. Through this fault-aware posture adaptation mechanism, FT-WBC synthesizes compensatory gaits under actuator failures and preserves as much arm workspace as possible while maintaining whole-body stability. Simulation and real-world experiments show that FT-WBC significantly improves survival rate and workspace under weakening or locked failures, and transfers zero-shot to a real legged manipulator in the real world.

An invariant extended Kalman filter (IEKF) is developed for state estimation of serial rigid manipulators with an arbitrary number of links, formulated entirely within the Lie group SE(3). The group-affine property of the kinematic equations makes the linearised error dynamics autonomous, so the Riccati equation governs the true error covariance rather than a local approximation. A physically separated noise model treats gyroscope and accelerometer channels independently: the accelerometer provides translational twist via gravity-compensated integration, yielding a measurement covariance that scales with the sample interval in exact analogy with process noise discretisation; a state-dependent Coriolis noise term captures gyroscope noise propagating through the nonlinear dynamics, vanishing at rest and growing with twist magnitude. The filter is structured as a modular chain of per-link IEKFs in which the predicted covariance of each link depends on its predecessor only through the Adjoint-transformed posterior, giving linear computational cost in link count. Exponential ultimate boundedness in mean square is established via a Lie algebra Lyapunov function, with per-link bounds chained through the Adjoint operator norm to yield a stability certificate that is modular and scalable to arbitrary chain length. Numerical results validate the design.

Deformable linear objects (DLOs) such as wires, cables, and ropes are common in robotic manipulation tasks, yet simulating them with both visual realism and physical accuracy remains challenging. Existing visual simulation methods typically rely on procedural geometric primitives that lack physically grounded deformation behavior, while physics-based approaches with robot learning support often approximate DLOs as rigid-link chains or generic soft bodies, failing to accurately capture the bending, twisting, and shear mechanics of slender elastic structures. In this work, we introduce DeformX, a co-simulation framework that integrates a dedicated Cosserat rod physics engine with NVIDIA Isaac Sim, enabling DLO simulations that are both physically faithful and visually realistic. Our Cosserat rod engine simulates the dynamics and self-collisions of DLOs, and contact interactions with arbitrary free-form meshes. To achieve high-fidelity visualization, we employ mesh skinning to map discrete rod deformations onto imported CAD models. To the best of our knowledge, DeformX is the one of the first frameworks for DLO simulation that unifies realistic visualization, principled physics, and compatibility with robot learning pipelines. We demonstrate its versatility across synthetic data generation and policy learning for DLO manipulation, and validate visual and physical fidelity through comparisons against real-world experiments. Notably, fine-tuning Segment Anything Model 3 (SAM3) on DeformX-generated data yields a 10.2% mAP@75 improvement in real-image wire segmentation, and a rope-swinging policy trained entirely in DeformX achieves a mean target-hitting error of 6.6 cm on a UR5e manipulator in real-world trials, highlighting its strong sim-to-real transfer capability.

Manipulation in confined environments, such as threading a manipulator through narrow apertures, remains a fundamental challenge, especially for conventional rigid robots. Hybrid rigid-soft manipulators offer promise but face two compounding planning challenges: backbone shapes feasible in free space become infeasible under environmental contact, and planning rigid and soft segments independently ignores their kinematic coupling. We present THREAD, the first diffusion-based trajectory planner for hybrid manipulation, learning a generative prior over physically realizable backbone trajectories conditioned on local environment geometry, with physics-inspired losses encoding curvature, smoothness, and collision constraints jointly across both segments. Trained in simulation, THREAD achieves 92.4% task success with 5x fewer collisions than the strongest baseline. We show cross-embodiment real-world transfer with minimal online updates, successfully threading through apertures as small as 1.3x the soft segment diameter.

The Manipulider is a buoyancy-actuated underwater robot that enables thrusterless, glide-like locomotion and attitude-based manipulation, while providing a magnetic modular interface for rapid payload swapping (e.g., a gripper or sensors). Four syringe-based buoyancy engines distributed around the body jointly regulate net buoyancy and the center of buoyancy, allowing the vehicle to maintain large tilt angles through static force balance without continuous thrust and to avoid propeller entanglement risks. We present the mechanical and electrical design, calibration procedure, and control architecture. Experiments with a gripper attached (no external payload) show a controllable buoyancy-displacement range of 40 mL per engine ({\approx}160 g total buoyancy authority), maximum statically stable tilts of 64.6° (single-engine) and 61.8° (dual-engine), and representative vertical and tilt-transition dynamics. We further demonstrate tilt regulation, controlled ascent/descent primitives, and a proof-of-concept gripper-based payload-transport sequence without thrusters.

This study presents a method for modeling diverse plant branches by iteratively estimating material parameters to support delicate branch manipulation. Branch manipulation is necessary in agricultural robotics for plant repositioning, stabilizing, and clearing visual obstructions in dense foliage. The proposed method builds a tetrahedral branch model from point-cloud data and simulates its behavior using the finite element method. Using real observed deformation data, it iteratively estimates branch parameters and then computes an optimal path with a deformation-aware motion planner to move and stabilize branches within another robot's field of view. Across 30 trials on branches with varying geometries and material properties, the proposed method reduced the deformation energy by 35.69% while increasing the path length by 8.10% on average.

Sampling-based Model Predictive Control (SMPC) is a promising strategy for contact-rich robotic manipulation, combining gradient-free optimization with massively parallel GPU simulation. Yet, most prior work relies on simplified dynamics or remains confined to simulation. We present an MPC framework that leverages JAX for large-scale parallelization and efficient computation, coupled with the high-fidelity MuJoCo MJX simulator, and deploy it on a Franka Research 3 executing the Push-T manipulation task through a complete real-to-sim-to-real pipeline. The MTP variant with structured global sampling outperforms unimodal baselines such as CEM, MPPI, and PS across tasks that require mode switching, both in simulation and on hardware. Furthermore, we evaluate online domain randomization within the MPC sample budget, showing that contact-initiation parameters yield interpretable adaptation signals, whereas global physics parameters provide feedback that is too weak for reliable exploitation at typical replanning frequencies. These findings highlight key challenges for sampling-based MPC in contact-rich manipulation-contact sensitivity, tight compute budgets, and the difficulty of obtaining informative domain-randomization signals in real time.

We present CORD-SLS, a real-time control method for safe deformable object manipulation, with a focus on ropes and cloth. At its core is a GPU-parallel differentiable simulator with contact smoothing which enables efficient gradient-based planning through intermittent contact. To robustly satisfy constraints under model and sensing uncertainty, we develop a real-time, GPU-parallel output-feedback robust model predictive control (MPC) algorithm that plans with this simulator. We further show that the simulator accelerates model-based RL for training neural manipulation policies. To improve real-world robustness, we use conformal prediction to calibrate visual-feedback and perception-error bounds for MPC, producing reachable tubes that enable high-probability safe control. We evaluate CORD-SLS on high-dimensional, contact-rich rope and cloth manipulation tasks in simulation and hardware, including obstacle avoidance, routing, folding, and smoothing. Across settings, CORD-SLS achieves millisecond-speed planning, exceeding baselines in safety, speed, and task success.

We consider the nonprehensile object transportation task known as the waiter's problem, in which a robot must move an object balanced on a tray from one location to another. In contrast to prior works on the robotic waiter's problem, which make the robot tilt a tray rigidly held by its end effector (EE), we use a tray suspended from the EE by ropes, such that it behaves like a three-dimensional pendulum. Some prior works have actuated the robot so that the EE simulates the behavior of a pendulum, because pendular motion reduces the shear forces acting on the transported objects, minimizing the sliding of rigid objects and sloshing in containers of liquid. In contrast, our use of a real hanging tray allows us to obtain the benefits of pendular motion while only actuating a 3 degree-of-freedom (DOF) mobile base, rather than requiring a full 6-DOF manipulator arm. Our experiments in simulation and on real hardware show that the hanging tray substantially reduces both sliding and sloshing compared to a static, rigidly-grasped tray. Furthermore, we integrate the hanging tray into an interactive robot waiter demonstration, which uses computer vision to identify people with a raised hand and visual servoing to steer toward them and allow them to access the tray.

Non-prehensile object manipulation skills are important for real-world robot interactions, enabling highly dynamic tasks such as balancing a glass on a tray or the controlled sliding of items on a table. Among such tasks, those characterised by high-speed manipulation requirements and general sensitivity of the resulting hybrid dynamics are particularly hard to accomplish. Within these, juggling can be seen as a highly challenging maneuver to be solved. The key to robotic juggling is achieving dynamic stabilisation of an underactuated object. Since the object does not possess the ability of self-correction, its stability is entirely dependent on the forces applied to it. This creates a system that is sensitive to control inputs, where timing is critical to continuously counteract deviations and maintain the desired behavior. We develop a systematic method to control a 7-degree-of-freedom manipulator performing non-prehensile ball juggling with a tool. Our primary contribution is a model-based framework for generating juggling trajectories and stabilizing a periodic juggling motion for this hybrid system. The framework incorporates a two-stage optimal control approach to compute the underlying feasible motion patterns required for stable juggling. Offline-computed trajectories are then organised to enable real-time error correction without solving optimal control problems online. We demonstrate the effectiveness of the resulting controller by first evaluating its performance in a simulation environment and performing an experiment using a Franka Emika Panda robot.

Robotic arms capable of traversing arbitrary spatial paths, especially in highly obstructed workspaces, are highly desired across several industries. Quaternion-joints have recently empowered a specific class of robotic arms -- cable-driven redundant manipulators -- beyond its prior capabilities. Specifically, quaternion-joints reduce the number of required motors per degree of freedom, paving the way for more compact solutions.An ongoing challenge is that the complexity of the kinematic model of quaternion joints challenges a priori decisions on manipulator configurations and imposes higher computational demands on the control system and its non-linearities amplify all discrepancies between design and physical artifact arising from fabrication imprecision. Here we show a that a 4-segment, 8-joint manipulator can achieve a broader workspace than extant configurations, at lower hardware cost, and that Residual Reinforcement Learning outperforms extant state-of-the-art methods -- specifically, the FABRIK algorithm -- on the control of such manipulator. Our results show that this configuration is more workspace-effective than prior designs, and that Residual Reinforcement Learning outperforms FABRIK by three orders of magnitude on positional and orientational accuracy, effecting precise control of the novel 4-segment, 8-joint manipulator. Additionally, the control implementation is simpler: we describe the complete FABRIK process for control and corresponding learning implementation. Our methodology is applicable to the design of new systems, providing designers with further tools for the development of this class of manipulators and corresponding control systems for novel configurations.

This work studies ``extreme motion generation'', which aims to maximize the Cartesian path length along a pre-defined trajectory within the manipulator's workspace. This objective is important in industry as long as path-following is fundamental to a large variety of tasks such as surface coating and welding. More critically, extreme motion enables a fixed-base manipulator to exploit the kinematic capability under limited reachability. However, such exploitation is challenging in practice, as the manipulator must actively avoid the safety boundary through execution, which is inherently a long-horizon problem. Accordingly, we claim that long-horizon decision-making should be delegated to a learning-based policy to maximize exploitation, while a classical model-based controller covers the near-boundary region, where the learning policy degrades sharply due to sparse data coverage. In detail, our proposed method is a step-level hybrid controller that switches between an RL-based and a model-based controller according to the normalized joint-limit distance. The initial joint configuration is sampled through conditional diffusion-based sampling, which improves the achievable path length based on the learned motion prior. We evaluate the proposed framework on 10,000 straight-line path-following tasks with a 7-DoF Franka FR3, extending the average rollout length by 27% over the model-based baseline. Notably, certain tasks yield a pronounced extension toward the motion extreme, as reflected in the maximum improvement reported in the statistical results. The project website and related videos of this paper can be found at https://yuan-xinyi.github.io/extreme-motion-generation/.