Contact-Rich Manipulation

We present a Learning from Demonstration (LfD) framework that achieves one-shot generalization in multi-stage, contact-rich manipulation tasks. Central to our approach is the utilization of environmental constraints as the inductive bias. By representing a demonstration as a sequence of behaviors that exploit environmental constraints, the robot separates task-general structure -- the constraint types and their transitions -- from instance-specific details such as exact demonstration trajectories, poses, and local geometries. Our four-stage pipeline builds a complete policy on this representation: the robot first abstracts a single demonstration into environmental-constraint primitives, then disambiguates them through self-guided exploration, next assimilates targeted human corrections that handle out-of-distribution variations, and finally recovers the abstracted-away details online through compliant interaction. Because the resulting policy follows constraints rather than mimics trajectories, it generalizes across object poses, local geometries, and unmodeled contact dynamics. We validate our approach on seven real-world multi-stage contact-rich manipulation tasks and achieve over 90% success. These extensive experimental results establish environmental constraints as fundamental building blocks for efficient generalization in learning from demonstration.

Flexible robotic manipulators (FRMs) offer advantages in lightweight design and large workspace, but their structural flexibility induces vibrations, accelerates fatigue, degrades tracking performance, and limits operational speed. These challenges are further amplified in multi-link serial manipulators, where increased overall length leads to greater structural flexibility. This article presents a backstepping output-feedback framework for fast vibration suppression and tip tracking of an n-degree-of-freedom serial flexible manipulator robot (nDSFMR), with a DeepONet-based approximation for practical deployment. Each link-joint is modeled as a Timoshenko beam coupled with an ODE and transformed into a canonical hyperbolic PDE with boundary dynamics. A backstepping-based boundary controller at the joint is developed to equivalently inject distributed damping along the beam, enabling rapid vibration suppression and trajectory tracking, only using available boundary measurements. To enable real-time implementation and scalability, a DeepONet neural operator is introduced to approximate the backstepping kernels, significantly reducing computational cost and facilitating fast controller updates under varying operating conditions. Experiments on a two-link flexible manipulator demonstrate faster vibration suppression and convergence of the end-effector to the desired trajectory, compared with a linear quadratic regulator (LQR) with feedforward control.

This work introduces a cooperative task capability improvement utilizing additional moments. The manipulators apply forces at the object's grasp point. Applying forces at a point other than the object's center of gravity produces undesired moments. The undesired moment acts as an additional moment. It improves the capability of an individual manipulator and, hence, the entire collaborative group. Any improvements in task capability directly add up to the object and transportation capability. The group's enhanced capability also helps achieve optimal capability, optimal resource allocation, and maximum fault tolerance in object manipulation. Our simulation results show an improvement in the capability of 5.86 % compared to when no moment is used to enhance the capability of the manipulators.

arly identification of motor impairment in infancy relies on expert visual assessment of spontaneous movement, motivating the development of automated, objective alternatives. One promising approach is using computer vision, which benefits from high quality pose estimation from video. In this study, we systematically evaluated three state-of-the-art pose estimation frameworks (MeTRAbs-ACAE, SAM 3D Body, and Sapiens) on 100 videos over 13 sessions of 8 infants recorded with a multi-view markerless motion capture system. We quantified keypoint detection accuracy using reprojection error, geometric consistency, and Procrustes-aligned 3D position error, and demonstrated proof-of-concept for fitting an inverse kinematic framework to infant data. While Sapiens achieved the lowest reprojection error and highest geometric consistency of the methods evaluated (22.8 pixels and 0.82, respectively), SAM 3D Body provided the most comprehensive 3D information for kinematic reconstruction with Procrustes-aligned position errors of 19 to 28 mm. We demonstrate in a case comparison example that biomechanical models fit to SAM 3D estimates distinguish representative movement patterns in infants related to motor development, as identified by a clinical expert. Together, these findings highlight both the promise and current limitations of 3D pose estimation for infant biomechanics and establish preliminary groundwork for scalable, video-based assessment of early motor development.

Open-source mobile manipulators have reached $660 (XLeRobot) but every sub-$1,000 platform shares three limitations: a fixed-height workspace, reactive-only control, and no protection against the stall-induced burn-out that destroys cheap Feetech servos. We present Nori Bot, a 17-DoF dual-arm mobile manipulator at $947 (~3% the cost of comparable commercial platforms) that addresses all three: (1) a 600mm Z-axis lift on the existing servo bus for floor-to-counter reach; (2) a thin-client Raspberry Pi 4 paired with the OpenClaw proactive agent runtime so cron jobs and hooks trigger physical tasks autonomously; and (3) a software safety stack with sensorless grip-force feedback via motor current on a soft TPU finger. Code, CAD, and the skill manifest will be released.

Robotic assembly in architectural construction faces a persistent bottleneck: existing planners are either highly specialized, requiring prohibitive retraining for every new geometric design, or operationally inefficient, treating structural sequencing and kinematic motion as disjoint processes. We present EUPHORIA, a unified framework that achieves universal few-shot adaptability and dynamic efficiency through a hybrid optimization strategy. To overcome the retraining bottleneck, we propose a Meta-Geometric Encoder based on Graph Hypernetworks: unlike standard contrastive learning, which performs only feature-level recognition, our hypernetwork dynamically generates policy parameters from a minimal support set, enabling parameter-level adaptation to complex topologies (e.g., domes, arches) without gradient-based retraining. For structural reasoning, we introduce a Physics-Informed Graph Transformer trained via Soft Actor-Critic (SAC), with a Physics-Bias Attention mechanism that modulates attention scores using contact forces from Discrete Element Model (DEM) simulations, guiding the planner toward structurally critical connections. We further ensure operational efficiency through Kinematics-Aware Sequencing, where the SAC objective penalizes high-energy transitions. Finally, we bridge the Sim2Real gap via Residual Stability Correction, a differentiable optimization layer that fine-tunes coarse assembly actions by minimizing a joint energy-stability cost prior to execution. Experiments show that EUPHORIA significantly reduces energy consumption over decoupled baselines and achieves state-of-the-art success rates on unseen, non-standard geometries with minimal few-shot examples, fusing meta-learning, physics-informed attention, and residual optimization into a cohesive, generalized planner.

This paper presents a novel framework for Jacobian computation in motion optimization problems involving multi-link systems, where physical quantities are represented using higher-order time derivatives. In motion optimization of robots and humans, cost functions may incorporate higher-order time derivatives, such as jerk or the time variation of forces, to capture smoothness and perceptual characteristics, particularly in motion skill analysis and expressive behaviors, thereby necessitating Jacobian computations involving these quantities. However, such Jacobians are typically computed using numerical or automatic differentiation without explicitly exploiting the underlying multi-link structure, which can lead to increased computational cost and numerical instability. To address this limitation, we propose a structured Jacobian formulation for motion optimization, based on the comprehensive motion computation framework, in which physical quantities and their higher-order time derivatives are systematically represented along the multi-link structure. The proposed method systematically derives analytical expressions for Jacobians of kinematic and dynamic quantities, including momentum, forces, and joint torques, with respect to generalized coordinates and their higher-order derivatives. The resulting framework is applicable to both direct and inverse optimization. Through numerical experiments, we demonstrate that the proposed method improves computational efficiency compared to numerical and automatic differentiation, while achieving comparable accuracy. Furthermore, we demonstrate its effectiveness in inverse optimization by recovering cost function weights from motion data. Together, these results indicate that the proposed formulation provides a scalable and structured computational foundation for motion optimization involving higher-order time derivatives in multi-link systems.

Legged manipulators extend robotic capabilities beyond static manipulation by integrating agile locomotion with versatile arm control. However, achieving precise manipulation while maintaining coordinated locomotion remains a major challenge. This work presents a hierarchical reinforcement learning framework for dynamic pick-and-place tasks using a quadruped equipped with a 6-DOF robotic arm. The framework incorporates an explicit mass estimation module enabling adaptive whole-body control for objects with varying weights. In simulation, the system achieves an 86.05% success rate with payloads up to 2.3 kg. The approach is further validated through real-world experiments across six representative scenarios with controlled variations in object physical properties (size and mass) and task heights. Specifically, within a wide vertical workspace ranging from ground level to 1.1~m-high tabletops, the system demonstrates an average success rate of 73.3% for payloads up to 1.3 kg, with an average execution time of 4.06 s. Unlike prior works that handle lightweight objects and execute pick-and-place motions with slow, piecewise motions, the proposed framework exploits concurrent locomotion and manipulation for dynamic, continuous execution. These results demonstrate the potential of quadrupedal mobile manipulators for adaptive, whole-body pick-and-place with heavier payloads and extended workspaces.

This paper presents a quadratic unconstrained binary optimization-based formulation framework for robot design optimization using kinematic structure-level evaluation metrics. In the proposed framework, classical computation is used to evaluate design-dependent metrics while the resulting combinatorial selection problem is formulated in a structure compatible with quantum annealing-based optimization. A robotic hand is adopted as a representative case study, as its performance is determined by both the individual kinematic characteristics of each finger and interaction terms. The proposed formulation incorporates individual design rewards, overlap workspace interactions, one-hot constraint, and structural dependency penalties into a unified quadratic model. A 27-variable robotic hand design problem is constructed, and simulated annealing is used as a classical baseline to verify the feasibility of the formulation. Quantum annealing is further performed to examine the applicability of the proposed formulation to annealing-based hardware execution. The results show that feasible design combinations satisfying both one-hot selection and pairwise constraints can be obtained, with the observed objective-value range becoming narrower as the number of reads increases. In addition, the formulation process is discussed for other robotic systems. The proposed framework provides a generalized approach for transforming kinematic structure-based robot design problems into combinatorial optimization problems.

Stochastic communication delays in teleoperation introduce signal discontinuities that undermine control stability and degrade control performance. Consequently, the conventional reinforcement learning (RL) methods struggle with the delayed observations due to the delay-induced observations, leading to high-frequency chattering. To address this, we propose a hybrid control framework, delay-resilient RL, integrating a state estimator utilizing Long Short-Term Memory (LSTM) with a residual RL policy, which is resilient to stochastic delays. The LSTM reconstructs smooth, continuous state estimates from delayed observations, enabling the RL agent to learn a residual torque compensation policy that balances tracking accuracy with velocity smoothness. Experimental validation on Franka Panda robots demonstrates that our approach significantly outperforms the state-of-the-art baselines, ensuring robust and stable teleoperation even under high-variance stochastic delays.

Robust state estimation for highly dynamic motion of legged robots remains challenging, especially in dynamic, contact-rich scenarios. Traditional approaches often rely on binary contact states that fail to capture the nuances of partial contact or directional slippage. This paper presents CoCo-InEKF, a differentiable invariant extended Kalman filter that utilizes continuous contact velocity covariances instead of binary contact states. These learned covariances allow the method to dynamically modulate contact confidence, accounting for more nuanced conditions ranging from firm contact to directional slippage or no contact. To predict these covariances for a set of predefined contact candidate points, we employ a lightweight neural network trained end-to-end using a state-error loss. This approach eliminates the need for heuristic ground-truth contact labels. In addition, we propose an automated contact candidate selection procedure and demonstrate that our method is insensitive to their exact placement. Experiments on a bipedal robot demonstrate a superior accuracy-efficiency tradeoff for linear velocity estimation, as well as improved filter consistency compared to baseline methods. This enables the robust execution of challenging motions, including dancing and complex ground interactions -- both in simulation and in the real world.

Explicit dynamic finite element (FE) simulations are widely used for large deformation engineering analysis, but repeated simulations remain costly during design space exploration and optimisation. In explicit FE analysis, nodal kinematics and element level deformation measures evolve through coupled node element updates. This motivates graph learned simulators that approximate one step FE state transitions and roll them out autoregressively. However, many mesh based graph surrogates are node centred, which makes element level variables and native nodal elemental exchange less direct to represent. This work proposes CAttBiGNN, a cross attention based bipartite graph neural network for coupled nodal elemental learning. The graph represents FE mesh nodes and elements as distinct entities linked by directed node element edges, enabling nodal displacement increments and element level deformation states to be predicted on their native discretisation domains. An edge aware cross attention processor uses geometric edge embeddings to modulate directional node element message passing. For larger graphs, CAttBiUGNN combines the bipartite processor with graph downsampling and upsampling to improve long-range information propagation. The method is evaluated on dome shaped cold forming and corner shaped hot forming benchmarks. Comparisons with node centred baselines and bipartite and attention ablations show improved accuracy and balance in nodal displacement and elemental thinning prediction during autoregressive rollout. The results indicate that the proposed finite element inspired learned simulator can support manufacturability oriented field prediction and efficient design space exploration in large deformation sheet material forming.

Text- and image-conditioned video generation models have achieved strong visual fidelity and temporal coherence, but they often fail to generate motion governed by kinematic and geometric constraints. In these settings, object parts must remain rigid, maintain contact or coupling with neighboring components, and transfer motion consistently across connected parts. These requirements are especially explicit in articulated mechanical assemblies, where motion is constrained by rigid-link geometry, contact/coupling relations, and transmission through kinematic chains. A generated video may therefore appear plausible while violating the intended mechanism, such as rotating a part that should translate, deforming a rigid component, breaking coupling between parts, or failing to move downstream components. To evaluate this gap, We introduce MechVerse, a benchmark for mechanically consistent image-to-video generation. MechVerse contains 21,156 synthetic clips from 1,357 mechanical assemblies across 141 categories, organized into three tiers of increasing kinematic complexity: independent articulation, pairwise coupling, and densely coupled multi-part mechanisms. Each clip is paired with a structured prompt describing part identities, stationary supports, moving components, motion primitives, direction, speed/extent, and inter-part dependencies. We evaluate proprietary, open-source, and fine-tuned image-to-video models using standard video metrics, instruction-following scores, and human judgments of motion correctness and kinematic coupling. Results show that current models can preserve appearance and smoothness while failing to generate mechanically admissible motion, with errors increasing as coupling complexity grows. MechVerse provides a benchmark for measuring and improving mechanism-aware video generation from image and language inputs.

Kinematic monitoring plays a critical role in long-term rehabilitation for patients with spinal cord injury (SCI), where multi-view markerless motion capture methods have shown significant potential. However, owing to the reliance on calibration and the difficulty of achieving multi-view synchronization, their deployment in patient self-deployed environments remains challenging. In this work, we propose an agentic pipeline for self-synchronized multi-view joint angle monitoring in uncalibrated environments using two cameras without hardware triggers. The Multimodal large language models enable automatic video synchronization and agent-driven self-verification. State-of-the-art monocular 2D pose estimation models are employed to extract candidate poses, where an agent-based selection mechanism is then applied to automatically identify and track the target subject, thereby producing consistent 2D poses in the presence of multiple individuals and occlusions. Such 2D poses are optimized to estimate joint angles from uncalibrated multi-view pose sequences, ensuring interpretability through explicit geometric modeling. Validation against Vicon system demonstrated the strong performance, achieving an MAE of $5.97^\circ \pm 2.36^\circ$ and a Pearson correlation coefficient of $0.962 \pm 0.014$. The proposed method is expected to provide a practical, patient self-deployable system to perform daily kinematic monitoring in uncalibrated home environments.

This paper presents an object manipulation strategy for the Variable Topology Truss (VTT) system, a truss robot that comprises actuated truss members connected by passive spherical joints. Although truss robots were originally proposed as rapidly deployable manipulators, manipulation strategy has not been studied thoroughly. To enable manipulation, we introduce a hybrid control framework that regulates position and force concurrently without explicit decoupling. At the actuator level, each member employs a sensor-based force feedback controller to generate the desired axial forces despite high actuator friction. At the task level, the forces applied at the end-effector nodes are produced by computing the required member forces using a static model of the VTT. We evaluate force-tracking performance through experiments on both a single member module and the full VTT system. Finally, we demonstrate object manipulation using two representative configurations and quantitatively assess combined position and force tracking performance. Experimental results confirm that the proposed approach enables consistent and reliable object manipulation with the VTT system.

Contact-rich robot dynamics are hybrid: a single observation can match several latent states and contact regimes (free, impact, stick--slip). A standard amortized filter that places no probability on a feasible contact transition will permanently lose the branch the robot actually follows. We introduce VHYDRO, a variational hybrid dynamics learner that prevents this branch loss. At each step, VHYDRO mixes the learned proposal with a feasible transition law before sampling and importance weighting, ensuring that every transition retained by the model-feasible carrier remains covered. VHYDRO jointly infers a continuous latent state and a discrete contact mode, and fits a sparse port-Hamiltonian law to each recovered regime. On top of this, three guarantees connect: support coverage stabilizes filtering, the stabilized filter concentrates the discrete contact posterior on coherent regimes, and mode-pure segments admit sparse port-Hamiltonian recovery. The recovery error separates cleanly into filtering, derivative, mode-impurity, and physics-residual parts. Three empirical findings track the same mechanism. Under heavy occlusion the support-safe filter stays usable while a non-defensive proposal collapses. On ManiSkill demonstrations and on four Sawyer/BridgeData task families the discrete state forms temporally coherent contact-regime segments that the discrete state yields a stronger joint profile across ARI, change-point F1, and segment purity than post-hoc and mode-free baselines. On hybrid systems with known equations the mode-conditioned sparse fit recovers the active physical terms; purely predictive baselines do not.

This paper addresses the Motion Execution Gap, the disconnect between high-level symbolic task descriptions using semantic constraints and executable robot motions. Motion Statecharts are introduced as an executable symbolic representation for complex motions. They allow the arbitrary arrangement of motion constraints, monitors or nested statecharts in parallel and sequence. World-centric motion specification and generalization across embodiments are enabled through the use of a unified differentiable kinematic world model of both, robots and environments. Motion execution is realized through a lMPC-based implementation of the task-function approach, in which smooth transitions during task switches are ensured using jerk bounds. Cross-platform transferability was demonstrated by deploying the method on eight robot platforms, operating in diverse environments. The proposed framework is called Giskard and is available open source: https://github.com/cram2/cognitive_robot_abstract_machine.

This paper presents a kinematics-aware deep reinforcement learning framework based on Rainbow Deep Q-Networks (DQN) for cooperative peg-in-hole manipulation by a Delta parallel robot and a 3-RRS (Revolute--Revolute--Spherical) parallel manipulator. A key contribution is the integration of a geometric design-optimization stage that precedes learning: the 3-RRS geometry is tuned to maximize the singularity-free workspace and improve conditioning, which in turn enlarges the safe region in which the reinforcement learning policy can explore. Together the two manipulators expose a 6~degree-of-freedom (DoF) controllable subspace (three Delta translations, two 3-RRS rotations, and one 3-RRS vertical translation); the peg-in-hole task is invariant to rotation about the peg axis, so the task-relevant manifold is five dimensional. The cooperative insertion problem is cast as a Markov Decision Process with a 12-dimensional state vector and a discrete action set containing $6 \times 2 = 12$ incremental commands (one positive and one negative per controlled DoF). A shaped reward combines dense proximity guidance, penalties for kinematic and workspace violations, and sparse bonuses for successful insertions. The Rainbow DQN -- integrating double Q-learning, dueling architecture, prioritized replay, multi-step returns, noisy linear layers for exploration, and a distributional value head -- is trained with a two-stage curriculum. The co-designed framework is validated in a high-fidelity kinematic simulator, where it achieves stable policy convergence, reliable insertions, and reduced constraint violations compared against a vanilla DQN agent and a classical sampling-based planner.

Discrete-time joint acceleration constraints are widely used to enforce position and velocity limits. However, under voltage-constrained electric actuators, kinematically admissible accelerations may be physically unrealizable, exposing a missing execution-level abstraction. We propose Voltage-Realizable Acceleration (VRA), a joint-level acceleration interface that grounds kinematic acceleration in voltage-constrained actuator physics by restricting commanded accelerations to voltage-realizable constraints. Hardware experiments on electric actuators and a wheel-legged quadruped show that VRA removes unrealizable accelerations, restores consistent near-constraint execution, and reduces constraint-induced oscillations.

Existing imitation learning methods enable robots to interact autonomously with the physical environment. However, contact-rich manipulation tasks remain a significant challenge due to complex contact dynamics that demand high-precision force feedback and control. Although recent efforts have attempted to integrate force/torque sensing into policies, how to build a simple yet effective framework that achieves robust generalization under multimodal observations remains an open question. In this paper, we propose ForceFlow, a force-aware reactive framework built upon flow matching. For contact-stage policy design, we investigate force signal fusion mechanisms and adopt an asymmetric multimodal fusion architecture that treats force as a global regulatory signal, combined with a joint prediction paradigm that enhances the policy's understanding of instantaneous force and historical information, thereby achieving deep coupling between force and motion. For task-level hierarchical decomposition, we divide manipulation into a vision-dominant approach stage (VLM-based pointing for target localization) and a touch-dominant interaction stage (force-driven contact execution), with a Vision-to-Force (V2F) handover mechanism that explicitly decouples spatial generalization from contact regulation. Experimental results across six real-world contact-rich tasks demonstrate that ForceFlow achieves a 37% success rate improvement over the strong baseline ForceVLA while maintaining significantly lower cost. Moreover, ForceFlow exhibits accurate force signal prediction and demonstrates superior performance in contact force self-regulation and zero-shot out-of-distribution (OOD) generalization.

Learning dynamic whole-body motions for legged robots through reinforcement learning (RL) remains challenging due to the high risk of failure, which makes efficient exploration difficult and often leads to unstable learning. In this paper, we propose External Force Guided Curriculum Learning (EFGCL), a guided RL approach based on the principle of physical guidance, in which external assistive forces are introduced during training. Inspired by spotting in artistic gymnastics, EFGCL enables agents to physically experience successful motion executions without relying on task-specific reward shaping or reference trajectories. Experiments on a quadrupedal robot performing Jump, Backflip, and Lateral-Flip tasks demonstrate that EFGCL accelerates learning of the Jump task by approximately a factor of two and enables the acquisition of complex whole body motions that conventional RL methods fail to learn. We further show that the learned policies can be deployed on real robot, reproducing motions consistent with those observed in simulation. These results indicate that physically guided exploration, which allows agents to experience success early in training, is an effective and general strategy for improving learning efficiency in dynamic whole-body motion tasks.

Articulated objects used in simulation and embodied AI are typically specified by geometry and kinematic structure, but lack the fine-grained dynamical effects that govern realistic mechanical behavior, such as frictional holding, detents, soft closing, and snap latching. Existing approaches either ignore the detailed structure of dynamics entirely, or use simple models with limited expressiveness. We introduce JODA, a framework for generating joint-level dynamics as a structured three-channel field over the joint degree of freedom, capturing conservative forces, dry friction, and damping. Instantiated using shape-constrained piecewise cubic interpolation (PCHIP), this formulation defines a compact and expressive function space that is both interpretable and compatible with differentiable simulation. Building on this representation, we develop methods for inferring and refining joint dynamics from multimodal inputs. Given visual observations and joint context, a vision-language model proposes structured dynamical primitives, which are composed into a unified dynamics field. The resulting representation supports both direct manipulation and gradient-based refinement. We demonstrate that JODA enables plausible and controllable modeling of diverse joint behaviors, providing a unified interface for inference, editing, and optimization. Code and example assets with their generated profiles will be released upon publication.

Accurate hand and finger tracking from video has significant clinical applications for monitoring activities of daily living and measuring range of motion, yet monocular video approaches for obtaining hand biomechanics remain under-developed. We present a method that combines the SAM 3D Body foundation model with inverse kinematics optimization in a full-body biomechanical model to extract anatomically-constrained finger joint angles from single-view video. We port SAM 3D Body from PyTorch to JAX for integration with MuJoCo-MJX, enabling GPU-accelerated optimization, and develop a novel mapping between the Momentum Human Rig (MHR) outputs and biomechanical model markers. Validation against 8-camera multiview reconstruction on 4,590 frames from 7 participants performing a variety of hand poses and object manipulation tasks shows finger joint angle errors of approximately 10 degrees and hand position errors of approximately 6 mm, after Procrustes alignment. Results were consistent across camera viewpoints and robust to different methods for producing reference values from multiview video. This work extends monocular biomechanical analysis to detailed finger tracking, expanding access to quantitative characterization of hand movement from readily available video.

Predicting the shape of tendon driven continuum robots (TDCRs) at steady state from actuation remains challenging due to continuous deformation, complex tendon routing, compliance, friction, and fabrication variability. In this paper, we address this problem as kinematic self modeling conditioned on action. We present a lightweight 3D printed TDCR hardware platform and an RGB-D data collection pipeline with multiple cameras, and we learn a point cloud flow matching model that maps motor actuation states to the robot's settled 3D geometry. The model is trained from randomly sampled quasi static configurations and evaluated on test motor commands within the same TDCR design family and actuation range. We compare against prior 3D deformable object and robot self modeling approaches in both MuJoCo simulation and real hardware experiments. Experiments on simulated 2-, 3-, and 5-module TDCRs and real 2- and 3-module robots show improved shape prediction accuracy under CD and EMD metrics. We further show in simulation that the same conditional formulation generalizes to tip payload as a conditioning input, enabling payload conditioned steady-state shape prediction. These results demonstrate a data driven self modeling framework for quasi static TDCR geometry prediction.

This paper introduces a low-cost experimental mockup to simulate the laser cutting process of containers in nuclear decommissioning. It is composed of a three-axis table supporting a cuboid container with ultraviolet-sensitive faces, a six-degree-of-freedom serial manipulator holding an ultraviolet torch that simulates the laser, and a visual system based on cameras and fiducial markers. The system employs a constrained task-space adaptive motion controller that compensates for inaccurate parameters and eliminates the need to calibrate the system. Furthermore, as the motion controller explicitly accounts for geometric constraints, the robot reactively avoids collisions with obstacles while handling the ultraviolet torch. To improve the tracking of the laser-cutting path, we control the ultraviolet beam, which requires only four degrees of freedom, instead of the full end-effector pose. Experiments show that, despite an initially uncalibrated system, the overall system is capable of tracking different trajectories with an overall mean accuracy of 3.9 (sd 2.5) mm when the end-effector pose is controlled and 2.4 (sd 1.3) mm when the ultraviolet beam is controlled.

We present a visuo-tactile data-collection system that generates temporally structured, contact-rich demonstrations for imitation learning. Conventional systems often decouple the operator from contact forces, which hinders the demonstration of subtle force modulation. Our system introduces a direct-drive gripper that the operator actuates with the fingers, preserving natural haptic feedback. Integrated visual sensors and custom tactile arrays capture image streams and contact geometry. A handle-mounted push button enables the operator to annotate the task's temporal structure in real time by marking task-critical regions. By fusing in-hand force perception with in-situ temporal annotation, the system produces multimodal datasets designed for coarse-to-fine learning algorithms that exploit structural task knowledge, enabling the development of high-quality manipulation policies.

Action-conditioned surgical video generation is a critical yet highly challenging problem for robotic surgery. The core difficulty is that low-dimensional control vectors must precisely govern complex image-space evolution. In this work, we propose a kinematic-to-visual lifting paradigm that converts articulated kinematics into a unified set of five image-aligned control modalities. Building on this representation, we introduce a hierarchically routed visual control framework that selectively activates the most relevant control modalities and motion scales. Instead of uniformly applying all control signals, our model performs hierarchical routing to dynamically allocate conditioning capacity. We further design kinematic-prior-guided routing loss functions to ensure physically meaningful, temporally stable, and efficient expert utilization. To improve efficiency, we propose a budgeted training and inference scheme that leverages routing-induced sparsity. By selectively discarding low-significance control pathways during training and execution, our approach enables adaptive computation that is complementary to standard distillation. We additionally construct a new benchmark with curated articulated annotations, obtained through human-in-the-loop semantic labeling and differentiable pose tracking, providing realistic supervision for action-conditioned surgical video generation. Extensive experiments demonstrate that our method consistently improves action faithfulness, visual fidelity, and cross-domain generalization over diverse baselines. Moreover, our efficient variant achieves substantial reductions in latency while maintaining strong control accuracy.

Reconstructing dynamic 3D scenes from blurry monocular videos is challenging as motion-induced blur entangles object motion and geometry, hindering geometric consistency. We present Kinematics-GS, a kinematics-aware framework that models blur as motion-aligned deformation and introduces a kinematic prior to reparameterize Gaussian shapes along motion trajectories, thereby mitigating degenerate shape collapse without auxiliary motion supervision. To stabilize optimization, we decompose scenes into dynamic and static components using temporal deformation variance and employ a coarse-to-fine deformation strategy to capture both global motion and fine-grained details. We also introduce a challenging real-world dataset of deformable and elastic objects exhibiting non-rigid motion with spatially non-uniform motion blur that obscures geometric cues. Extensive experiments on real-world benchmarks with realistic motion blur demonstrate that Kinematics-GS outperforms prior methods by a clear margin in monocular dynamic scene reconstruction, highlighting its effectiveness in handling complex and non-rigid motion scenarios.

The ability to derive precise spatial and physical insights is a cornerstone of vision-language models (VLMs), yet their poor performances in related spatial intelligence tasks such as physical reasoning remain a fundamental barrier. The community critically lacks a scientific analysis revealing whether VLMs faithfully reach answers or plausibly make guesses. This work aims to provide a fundamental understanding of how VLMs perceive the physical world, and utilize physical laws, while assessing the reliability of model confidence. We propose NICE and FACT, a dual-diagnostic paradigm that explicitly decomposes quantitative reasoning for kinematic physics: FACT diagnoses visual fidelity, physical law comprehension, and temporal grounding. NICE studies our novel neighborhood-informed calibration method and novel metrics to evaluate and calibrate confidence reliability. Evaluated across 6 latest state-of-the-art VLMs, we uncover that models fail to identify visual preconditions or utilize necessary physical laws to reach answers. This work highlights and establishes a standardized diagnostic paradigm to guide the development of faithful, physically-grounded VLMs.

We prove that aerodynamic co-contraction in a redundant dual-rotor actuator can tune a passive, trim-defined aero-mechanical damping while keeping the commanded net force constant. In particular, we define an incremental damping coefficient as the local sensitivity of net thrust to air-relative velocity at a trim and prove that it increases monotonically along constant-force fibers under a mild aerodynamic hardening condition. We then validate the required damping and hardening properties from a first-principles Blade Element Theory derivation, which yields a minimal thrust model affine in inflow and explicitly reveals the speed--inflow coupling driving the effect. The resulting mechanism is formalized as a Variable Aerodynamic Damping Actuator (VADA) and shown to be dynamically isomorphic to stiffness modulation in antagonistic variable-stiffness actuation (VSA), similar to the co-contraction of tendons by muscle co-activation. The same fiber-density principle also enhances the active aerodynamic promptness measure of redundant multirotors. Finally, an impedance-form representation clarifies the roles of common-mode and differential-mode actuation in the control of passive impedance and the equilibrium velocity of the VADA system.

Adaptive control of Euler-Lagrange systems is challenging when friction is governed by a finite-horizon internal state that is not directly observable from joint measurements. In this setting, the measured closed-loop state is no longer Markovian, and standard certainty-equivalence adaptive laws may lose their convergence guarantees. The paper proposes a meta-control architecture in which the gains of a computed-torque controller are generated by a self-attention block processing a short window of recent motion history. The number of attention heads is selected before policy training through a surrogate analysis of the autocovariance of the memory-state gradient along the temporal window. This surrogate is based on a temporal adaptation of an incremental rank-tracking framework previously developed by the authors. The selected head count is then fixed and used as an architectural hyperparameter in a reinforcement-learning stage, where the policy is trained under a shielded admissibility constraint. The approach is tested on a 2-DOF manipulator with nonlinear friction and variable payload. In the short and matched memory regimes, the single-layer attention-only meta-controller outperforms a deeper Transformer baseline, with tracking-error reductions of 12 and 19 percentage points, respectively. The reported effect sizes are large, with d approximately -1.1 and -2.1, and Mann-Whitney p < 0.05 in both cases. In the long memory regime, however, the advantage disappears. Four out of ten training runs show either divergence or payload-invariant policy collapse, revealing a weakness in the static Phase-1 head-count prescription. This motivates moving rank-tracking inside the reinforcement-learning loop, allowing attention heads to be pruned or grown at runtime instead of fixed before training.

Generating realistic 3D Human-Object Interactions (HOI) is a fundamental task for applications ranging from embodied AI to virtual content creation, which requires harmonizing high-level semantic intent with strict low-level physical constraints. Existing methods excel at semantic alignment, however, they struggle to maintain precise object contact. We reveal a key finding termed \textit{Geometric Forgetting}: as diffusion model depth increases, semantic feature tend to overshadow object geometry feature, causing the model to lose its perception to object geometry. To address this, we propose MaMi-HOI, a hierarchical framework reconciling \textbf{Ma}cro-level kinematic fluidity with \textbf{Mi}cro-level spatial precision. First, to counteract geometric forgetting, we introduce the Geometry-Aware Proximity Adapter (GAPA), which explicitly re-injects dense object details to perform residual snapping corrections for precise contact. Nevertheless, such aggressive local enforcement can disrupt global dynamics, leading to robotic stiffness. In response, we introduce the Kinematic Harmony Adapter (KHA), which proactively aligns whole-body posture with spatial objectives, ensuring the skeleton actively accommodates constraints without compromising naturalness. Extensive experiments validate that MaMi-HOI simultaneously achieves natural motion and precise contact. Crucially, it extends generation capabilities to long-term tasks with complex trajectories, effectively bridging the gap between global navigation and high-fidelity manipulation in 3D scenes. Code is available at https://github.com/DON738110198/MaMi-HOI.git

LIPM is everywhere in legged-locomotion control, but almost always as a modeling choice rather than as something the controller's cost actually prefers. This note tries to make that link more explicit. Working from a small centroidal OCP that penalizes the rate of angular momentum, we look at what its optimum tends to look like. Three things come out. With full-rank stance, the optimum drifts toward a pendular force pattern at a rate determined by the SVD of the moment Jacobian; the constant is set by foot-span geometry and matches the experiments to within 16%. With N=2 stance, as in trot, the friction cone introduces a lower bound on $\|\dot{H}_G\|$ that no amount of weight tuning fixes; we also see a non-smooth feasibility kink at a critical horizontal acceleration that we can write in closed form. Adding a task term that asks for a nonzero $\dot{H}_G$ moves the optimum off the pendular set in a predictable way. None of this is far from the classical ZMP/DCM picture. We test these claims on a point-mass quadruped and on the Unitree Go1 in MuJoCo (open-loop QP and a torque-level closed-loop controller), and we note where the asymptotic story stops being a good description of what the closed loop actually does.

This paper presents a subsystem-based adaptive control framework for serial flexible manipulators with an arbitrary number of links, in which the elastic deformation PDE of each link is carried through the entire control design without spatial discretization or modal truncation. All dynamic quantities -- rigid-body motion, elastic deformation, and inter-link constraint forces -- are expressed uniformly as body-fixed twists and wrenches within the se3 Lie-algebraic structure. A controllable form of the per-link dynamics is derived by substituting the strain-based deformation PDE into the dynamic equation, eliminating distributed elastic acceleration and yielding a model governed by the body-fixed twist acceleration and deformation field. Desired subsystem twist trajectories are generated via a deflection-compensating inverse kinematics procedure. A nominal per-link controller is proven to produce exponential twist error decay via a per-subsystem Lyapunov function. An adaptive modification replaces exact physical parameters with online estimates governed by a projection-based law, augmenting with a parameter estimation error term. Upon summing over all links, the interaction power terms telescope to zero by Newton's third law and the frame invariance of the natural power pairing on se3se(3), establishing exponential convergence of all twist errors and bounded elastic deformation under both nominal and adaptive controllers. The screw-theoretic structure renders interaction term cancellation exact, making the stability certificate modular and scalable to chains of arbitrary length. The framework is validated numerically on a two-link flexible manipulator in three-dimensional motion.

Gap-closing rate and visual looming swap discriminative dominance depending on deceleration intensity - a finding that reconciles a long-standing conflict in the car-following literature and challenges spacing-centered assumptions in traditional driver behavior models. This study presents a two-stage analytical framework that distinguishes between information availability (kinematic variables measurable in the environment) and information utilization (variables that demonstrably separate driver behavioral patterns), applied to 1,060,119 valid car-following observations from the NGSIM trajectory dataset (2,932 vehicles). Six kinematic features are extracted, and deceleration events are detected under two threshold conditions (-0.5 m/s^2 and -0.3 m/s^2). K-means clustering identifies behavioral modes, and one-way ANOVA with eta-squared effect sizes ranks each feature's discriminative power. Three key findings emerge: (1) threshold selection fundamentally shapes behavioral inference - the stricter threshold yields three interpretable modes while the permissive threshold collapses these to two; (2) hard braking prioritizes gap-closing rate (eta^2 = 0.715) while moderate braking emphasizes visual looming (eta^2 = 0.574); and (3) spacing headway is negligible (eta^2 <= 0.014) across both thresholds. These findings provide empirically grounded candidates for perceptual cue prioritization and have direct implications for ADAS warning system design and autonomous vehicle control.

Generating realistic reactive motions, in which one person reacts to the fixed motions of others, is challenging due to strict interaction constraints and a limited feasible solution space. This paper focuses on a typical scenario: duet dance, where high-quality data is scarce, motion patterns are complex, and the details of human interactions are both intricate and abundant. To tackle these challenges, we propose a novel two-stage framework. In the first stage, we introduce a motion VQ-VAE with separate body-part encoders and a joint decoder, enabling specialized codebooks to enhance representation capacity while dynamically modeling dependencies across body parts during decoding, thereby preventing inconsistencies in the generated motions. In the second stage, we propose a contact-aware diffusion model for reactive motion generation that jointly generates motion and a contact matrix between individuals, enabling explicit interaction modeling and providing guidance toward more precise and constrained interaction dynamics during sampling. Experiments show that our method outperforms Duolando with lower $\text{FID}_k$ (8.89 vs. 25.30) and $\text{FID}_{cd}$ (8.01 vs. 9.97), as well as a higher BED (0.4606 vs. 0.2858), indicating improved interaction fidelity and rhythmic synchronization.

This paper presents a multi-phase whole-body model predictive control (MPC) approach for bipedal walking, combining a detailed whole-body model in the near horizon with a simplified single-rigid-body model in the later prediction steps. This reduces computational complexity while retaining prediction capabilities. The resulting nonlinear optimal control problem is solved entirely within the general-purpose, off-the-shelf nonlinear MPC framework acados, using sequential quadratic programming (SQP). Given a contact schedule and a target walking speed, the controller optimizes joint torques without depending on preselected footstep locations. The controller is validated in MuJoCo simulation on the 18-DoF bipedal robot HyPer-2.

When deploying reinforcement learning policies to physical robots, actuator rate constraints -- hard limits on how fast each joint can move per control step -- are unavoidable. These limits vary substantially across joints due to differences in motor inertia, power bandwidth, and transmission stiffness, creating pronounced heterogeneity that existing methods fail to handle geometrically: the per-joint feasible region forms a high-dimensional box in action-increment space, yet QP projection and spherical parameterization methods impose isotropic ball-shaped constraints, exponentially under-covering the true feasible set as heterogeneity grows. This paper proposes Dynamic Decoupled Spherical Radial Squashing (DD-SRad), which resolves this mismatch by computing a position-adaptive radius independently for each actuator, achieving tight alignment with the true per-joint feasible region. DD-SRad satisfies per-step hard constraints with probability~1, preserves well-conditioned gradients throughout training, and admits exact policy gradient backpropagation with zero runtime solver overhead. MuJoCo benchmark experiments demonstrate the highest task return at zero constraint violation -- matching the unconstrained upper bound -- with 30%--50% improvement in constraint-space coverage over spherical baselines. High-fidelity IsaacLab simulations with Unitree H1 and G1 humanoid robots confirm end-to-end optimality parameterized directly from official joint specifications, validating a systematic pathway from hardware datasheets to safe deployment.

This paper mainly studies the accurate height jumping control of wheeled-bipedal robots based on torque planning and energy consumption optimization. Due to the characteristics of underactuated, nonlinear estimation, and instantaneous impact in the jumping process, accurate control of the wheeled-bipedal robot's jumping height is complicated. In reality, robots often jump at excessive height to ensure safety, causing additional motor loss, greater ground reaction force and more energy consumption. To solve this problem, a novel wheeled-bipedal jumping dynamical model(W-JBD) is proposed to achieve accurate height control. It performs well but not suitable for the real robot because the torque has a striking step. Therefore, the Bayesian optimization for torque planning method(BOTP) is proposed, which can obtain the optimal torque planning without accurate dynamic model and within few iterations. BOTP method can reduce 82.3% height error, 26.9% energy cost with continuous torque curve. This result is validated in the Webots simulation platform. Based on the torque curve obtained in the W-JBD model to narrow the searching space, BOTP can quickly converge (40 times on average). Cooperating W-JBD model and BOTP method, it is possible to achieve the height control of real robots with reasonable times of experiments.

Domain randomization (DR) is widely used in policy learning to improve robustness to modeling error, but remains underexplored in contact-rich sampling-based predictive control (SPC), where rollout quality is highly sensitive to uncertainty. In this work, we take the first step by studying risk-aware DR in predictive sampling on a simple yet representative Push-T task, comparing average, optimistic, and pessimistic rollout aggregations under randomized model instances. Our initial results suggest that DR affects not only robustness to model error, but also the effective cost landscape seen by the sampling-based optimizer, by reshaping the basin of attraction around contact-producing actions. This opens up potential for exploring better grounded risk-aware contact-rich SPC under model uncertainty. Video: https://youtu.be/f1F0ALXxhSM

Purpose: Six million people use crutches as mobile aids in the US. Rigid designs with no axial mobility limit sensory feedback and lead to secondary injury on the upper joints. Spring-loaded designs offer compliance but may compromise stability. We designed a biologically inspired tensegrity crutch with a compliant module aiming to achieve favorable mechanical properties. The terminal module was a pre-stressed self-tensile two-cell tensegrity structure. We compared the tensegrity crutch to commercial rigid and spring-loaded crutches in mechanical tests using axial loading, in overground straight and turning walking, and in participant experience. Methods: In human trials, healthy young adults (N=18) with no recent lower-body injury performed straight walking and turning trials at a comfortable self-selected pace. A knee blocker simulated unilateral injury of the dominant leg. After using each type of crutch, participants reported their perceived levels of effort, comfort, pain, stability, and usability. Results: Compared to the rigid design, both spring-loaded and tensegrity conditions reduced peak loading rates. The tensegrity design improved effort, comfort, pain, and usability. Spring-loaded crutches reduced perceived stability and walking speed. Conclusion: The biologically inspired tensegrity crutches were an overall improvement to existing designs. Simulations and mechanical testing suggest that nonlinear stiffness, ground-following, and force feedback are among the beneficial mechanical properties that underlie this improvement.

While Large Language Models (LLMs) and Vision-Language Models (VLMs) demonstrate remarkable capabilities in high-level reasoning and semantic understanding, applying them directly to contact-rich manipulation remains a challenge due to their lack of explicit physical grounding and inability to perform adaptive control. To bridge this gap, we propose CoRAL (Contact-Rich Adaptive LLM-based control), a modular framework that enables zero-shot planning by decoupling high-level reasoning from low-level control. Unlike black-box policies, CoRAL uses LLMs not as direct controllers, but as cost designers that synthesize context-aware objective functions for a sampling-based motion planner (MPPI). To address the ambiguity of physical parameters in visual data, we introduce a neuro-symbolic adaptation loop: a VLM provides semantic priors for environmental dynamics, such as mass and friction estimates, which are then explicitly refined in real time via online system identification, while the LLM iteratively modulates the cost-function structure to correct strategic errors based on interaction feedback. Furthermore, a retrieval-based memory unit allows the system to reuse successful strategies across recurrent tasks. This hierarchical architecture ensures real-time control stability by decoupling high-level semantic reasoning from reactive execution, effectively bridging the gap between slow LLM inference and dynamic contact requirements. We validate CoRAL on both simulation and real-world hardware across challenging and novel tasks, such as flipping objects against walls by leveraging extrinsic contacts. Experiments demonstrate that CoRAL outperforms state-of-the-art VLA and foundation-model-based planner baselines by boosting success rates over 50% on average in unseen contact-rich scenarios, effectively handling sim-to-real gaps through its adaptive physical understanding.

Lower limb exoskeletons (LLEs) present the potential to make motor-impaired individuals walk again. Their application in real-world environments is still limited by the lack of effective adaptive gait planning. Indeed, current exoskeletons are meant to walk only on a flat and even terrain. Generating environment-aware, physiologically consistent gait trajectories in real-time is an open challenge. To overcome this, we propose a novel Kernelized Movement Primitives (KMP)-based framework for adaptive gait generation (AGG) across multiple indoor terrains. The proposed approach learns a probabilistic representation of human gait in both the joint and task spaces from a limited number of human demonstrations, representing natural gait characteristics and ensuring kinematic feasibility. In addition, the learned trajectories are adapted using environmental information extracted from an onboard RGB-D camera by treating the AGG as a linearly constrained optimization problem with via-points. The proposed method has been thoroughly validated first in simulations for gait generation in different scenarios, such as flat-ground walking, slopes, stairs, and obstacles crossing. Finally, the effectiveness and robustness of the method have been demonstrated with experiments on a commercial LLE in real-world scenarios. The results obtained demonstrate the feasibility of an environment-aware gait planning system for a new generation of intelligent lower limb exoskeletons for assisting people with disabilities in their every-day life.

This paper investigates singular configurations of planar 3-RPR parallel manipulators, which result from applying the averaging technique to solution pairs of their direct kinematic problem. Without computing the zeros of the corresponding degree 6 polynomial we parametrize the input pairs and determine their relative orientation in a way that the flexion order of the averaged configurations increases. Moreover, the obtained results are visualized for concrete examples. The presented methodology can also be used for studying the spherical and spatial analogues of planar 3-RPR parallel manipulators.

This paper presents a novel model predictive control (MPC) approach for autonomous pick-and-place between moving platforms with a hook-equipped aerial manipulator. First, for accurate and rapid modeling of the complex dynamics, a digital twin model of the quadcopter equipped with a hook-based gripper, implemented in MuJoCo, is constructed and used as the predictive model for the MPC. To handle uncertainties of the predictive model (e.g. due to aerodynamics and uncertain payloads), a robust adaptive MPC approach is proposed. By systematic integration of zero-order robust optimization (zoRO) based uncertainty propagation and an extended Kalman filter (EKF) for parameter estimation, the MPC algorithm ensures robust constraint satisfaction, high performance, and computational efficiency. The effectiveness of the proposed method is evaluated in complex simulated scenarios and in real-world flight experiments.

Multimodal resources for non-periodic court sports with laboratory-grade sensing remain scarce: few publicly pair instrumented ground reaction force (GRF) with high-frame-rate multi-view video, limiting markerless load estimation in realistic training settings. BadmintonGRF records eight synchronized RGB views at ~120 FPS, four Kistler force plates, and Vicon motion capture (C3D) without hardware genlock across modalities; alignment combines human-verified events, automated quality assurance, and per-camera time offsets with uncertainty metadata. Tier 1 distributes pose, time-aligned GRF, metadata, and splits under CC BY-NC 4.0, enabling the primary benchmark without raw RGB or C3D; we report a Tier 1 task that maps 2D pose to GRF. Tier 2 provides raw RGB and C3D under controlled access for studies that require appearance or full kinematics. The public release contains 17,425 impact-segment archives in the 10-subject benchmark tree (156 instrumented trials; raw multi-view RGB alone exceeds 1 TB); benchmark loader gates retain 12,867 view-specific instances and 1,732 unique impacts after multi-view deduplication. We are not aware of prior public badminton corpora that combine this sensing layout with audited video--GRF alignment for impact-centric GRF estimation. We distribute preprocessing code, leave-one-subject-out splits, ten reference baselines, and optional late fusion (one deterministic test-time pass per instance; no test-time augmentation), with a within-trial diagnostic in the supplementary material.

In this paper, we design feedback control laws for soft robots modelled using the Cosserat rod, which is spatially discretised using the Piecewise Constant Strain (PCS) approach. The PCS approach transforms the nonlinear PDEs describing the Cosserat rod to a system of nonlinear ODEs. This simplification results in a model describing soft robots which is similar to the serial rigid-link manipulators. We design feedback control laws for the quasi-static PCS model by using external wrenches as control inputs. The control laws are designed based on state-feedback linearisation in strain and task spaces. An extensive set of numerical results demonstrates the performance of the control laws for end-effector trajectory tracking and shape control of soft robots.

Quadrupedal locomotion plays a critical role in enabling agile, versatile movement across complex terrains. Understanding and estimating the underlying physical dynamics are essential for achieving efficient and stable quadrupedal locomotion. We propose a novel training framework for quadrupedal locomotion that enables the Control Policy to understand and reason about physical dynamics. In simulation, we concurrently train an Intrinsic Dynamics (ID) Head that learns state-to-torque dynamics alongside the Control Policy, and we define a dynamics reward enabled by the ID Head that encourages the Policy toward more predictable dynamical behavior. We also provide a mechanism to tune the learned dynamics in the resulting Policy by controlling the training coefficients of the ID Head. Our simulation experiments show that this mechanism drives convergence to better optima across a wide range of standard quadrupedal locomotion rewards, yielding more efficient and smoother policies. Our real-robot experiments demonstrate sim-to-real transfer of these improvements, with significant gains in torque efficiency (16.8%), action rate (18.6%), and mechanical power (12.8%), while improving safe torque occupancy by 6.4%.

Grasp force estimation can help prevent robots from damaging delicate objects during manipulation and improve learning-based robotic control. Integrating force sensing into deformable grippers negotiates trade-offs in cost, complexity, mechanical robustness, and performance. With the growing integration of RGB-D wrist cameras into robotic systems for control purposes, camera-based techniques are a promising solution for indirect visual force estimation. Current approaches mostly utilize end-to-end deep learning, which can be brittle when generalizing to new scenarios, while existing model-based approaches are unsuited to grasping and modern grasper geometries. To address these challenges, we developed a model-based visual force sensing approach integrating an iterative contact localization with generalization to unseen objects. The system extracts structural key points from wrist camera RGB-D images of deforming fin-ray-shaped soft grippers, and uses these key points to define parameters of an inverse finite element analysis simulation in Simulation Open Framework Architecture. The iterative contact localization sub-system utilizes a deep learning-based online 3D reconstruction and pose estimation pipeline to dynamically update contact location, and is robust to visual occlusion and unseen objects. Our system demonstrated an average root mean square error of 0.23 N and normalized root mean square deviation of 2.11% during the load phase, and 0.48 N and 4.34% over the entire grasping process when interacting with different objects under various conditions, showcasing its potential for real-time model-based indirect force sensing of soft grippers.

Robotic-assisted surgery offers significant clinical advantages but largely eliminates direct haptic feedback, increasing the risk of excessive tool-tissue interaction forces. Although recent commercial systems have begun to introduce force feedback, their high cost limits accessibility, particularly for surgical training. This paper presents a modular experimental robotic laparoscopic instrument integrated with a real-time haptic feedback framework. The proposed instrument employs a wrist-mounted force/torque (F/T) sensor to estimate tool-tissue interaction forces while avoiding the durability and integration challenges of tip-mounted sensors. A haptic feedback framework is developed to extract the external contact forces, render them to the haptic device, and generate stable and perceptually meaningful feedback. The instrument is integrated into the robotic surgery training system (RoboScope) and evaluated through a controlled user study involving a force regulation task. Experimental results demonstrate that haptic feedback significantly improves task success rate, force regulation accuracy, and task efficiency compared to visual-only feedback. The proposed instrument enables stable, high-fidelity haptic interaction, supporting effective robotic surgery training.

Contact-rich manipulation is challenging due to its high dimensionality, the requirement for long time horizons, and the presence of hybrid contact dynamics. Sampling-based methods have become a popular approach for this class of problems, but without explicit mechanisms for global exploration, they are susceptible to converging to poor local minima. In this paper, we introduce Global-MPPI, a unified trajectory optimization framework that integrates global exploration and local refinement. At the global level, we leverage kernel sum-of-squares optimization to identify globally promising regions of the solution space. To enable reliable performance for the non-smooth landscapes inherent to contact-rich manipulation, we introduce a graduated non-convexity strategy based on log-sum-exp smoothing, which transitions the optimization landscape from a smoothed surrogate to the original non-smooth objective. Finally, we employ the model-predictive path integral method to locally refine the solution. We evaluate Global-MPPI on high-dimensional, long-horizon contact-rich tasks, including the PushT task and dexterous in-hand manipulation. Experimental results demonstrate that our approach robustly uncovers high-quality solutions, achieving faster convergence and lower final costs compared to existing baseline methods.

This paper discusses null-space wrench components in parallel manipulators. We examine the adaptation of the two most common characterizations of these components in grasp-like systems, namely, interaction forces and internal loads, to parallel manipulators with actuation redundancy. We identify critical oversights in the existing literature on the subject, resolve ambiguities related to the definitions of interaction forces and internal loads, and provide explicit methods for synthesizing equilibrating and manipulating joint torque vectors. A case study is also provided to justify the validity of our novel methods and correct erroneous results reported in the literature.

This paper presents a planning pipeline framework for locomotion in rope-assisted robots climbing vertical surfaces. The proposed framework is formulated as a bi-level optimization scheme that addresses a mixed-integer problem: selecting feasible terrain regions for landing while simultaneously optimizing the control inputs, namely rope tensions and leg forces, and landing location. The outer level of the optimization is solved using the Cross-Entropy Method, while the inner level relies on gradient-based nonlinear optimization to compute dynamically feasible motions. The approach is validated on a novel climbing robot platform, ALPINE, across a variety of challenging terrain configurations.

Articulation modeling aims to infer movable parts and their motion parameters for a 3D object, enabling interactive animation, simulation, and shape editing. In this paper, we present Sketch2Arti, the first sketch-based articulation modeling system for CAD objects. Our key observation is that designers naturally communicate articulation intent through lightweight sketches (e.g., arrows and strokes) that indicate how parts should move, yet translating such sketches into articulated 3D models remains largely manual. Sketch2Arti bridges this gap by enabling users to specify articulation through simple 2D sketches drawn from a chosen viewpoint. Given a CAD model and user sketches, our approach automatically discovers the corresponding movable parts and predicts their motion parameters, allowing iterative modeling of multiple articulations on complex objects with fine-grained control. Importantly, Sketch2Arti is trained in a category-agnostic manner without requiring object category information, leading to strong generalization to diverse objects beyond existing articulation datasets. Moreover, for shell models lacking interior structures, Sketch2Arti supports controllable internal completion guided by user sketches, generating plausible internal components consistent with the existing geometry and predicted motion constraints. Comprehensive experiments and user evaluations demonstrate the effectiveness, controllability, and generalization of Sketch2Arti. The code, dataset, and the prototype system are at https://arlo-yang.github.io/Sketch2Arti.

Training machine learning models for robotic tactile sensing requires vast amounts of data, yet obtaining realistic interaction data remains a challenge due to physical complexity and variability. Simulating tactile sensors is thus a crucial step in accelerating progress. This paper presents SPLIT, a novel method for simulating image-based tactile sensors, with a primary focus on the DIGIT sensor. Central to our approach is a latent space arithmetic strategy that explicitly disentangles contact geometry from sensor-specific optical properties. Unlike methods that require recalibration for every new unit, this disentanglement allows SPLIT to adapt to diverse DIGIT backgrounds and even transfer data to distinct sensors like the GelSight R1.5 without full model retraining. Beyond this adaptability, our approach achieves faster inference speeds than existing alternatives. Furthermore, we provide a calibrated finite element method (FEM) soft-body mesh simulation with variable resolution, offering a tunable trade-off between speed and fidelity. Additionally, our algorithm supports bidirectional simulation, allowing for both the generation of realistic images from deformation meshes and the reconstruction of meshes from tactile images. This versatility makes SPLIT a valuable tool for accelerating progress in robotic tactile sensing research.

Wearable sensor-based human gait analysis holds great promise in healthcare, rehabilitation, clinical diagnosis and monitoring, and sports activities. Specifically, ground reaction force (GRF) provides essential insights into the body's interaction with the ground during movement and is typically measured using instrumented treadmills equipped with force plates. However, such equipment is expensive and restricted to laboratory environments. To enable a more portable solution, wearable insole sensors have been used to measure GRF. These sensors, however, are prone to noise and external interference, which reduces measurement accuracy. Deep learning methodologies could be adopted to address these issues, but they often require significant computing resources to achieve high accuracy, limiting their applicability for real-time analysis on portable devices. To overcome these limitations, we propose Selective Correlation Based Knowledge Distillation (SCKD) for estimating GRF from data collected by insole sensors. Our proposed method utilizes selected features considering temporal characteristics in the process of extracting correlation maps for knowledge transfer, enhancing interpretability and mitigating issues in high dimensional data processing. We demonstrate the effectiveness of the compact models generated by our distillation framework through comparison with existing methods. Various configurations of teacher-student architectures and training approaches are examined based on multiple evaluation criteria, utilizing data collected at different walking speeds and with different window sizes. Experimental results confirm that our approach outperforms existing methods in estimating GRF from wearable insole sensor data. Therefore, our approach offers a reliable and resource-efficient solution for human gait analysis.

Humanoid robots operating in human-centered environments (e.g., homes, hospitals, and offices) must mitigate foot--ground impact transients, as impact-induced vibration and noise degrade user experience and repeated impacts accelerate hardware wear. However, existing low-noise locomotion training often relies on kinematic proxy objectives or fragile force sensors, and footwear-induced changes in contact dynamics introduce distribution shifts that hinder policy generalization.We present QuietWalk, a physics-informed reinforcement learning framework for ground-reaction-force-aware humanoid locomotion under diverse footwear conditions. QuietWalk employs an inverse-dynamics-constrained physics-informed neural network (PINN) to estimate per-foot vertical ground reaction forces (GRFs) from proprioceptive signals, and integrates the frozen predictor into the RL training loop to penalize predicted impact forces without requiring force sensors at deployment.On a held-out real-robot dataset, enforcing inverse-dynamics consistency reduces vertical GRF prediction errors by 82%-86% compared with a purely supervised predictor and improves the coefficient of determination from 0.39/0.67 to 0.99/0.99 for the left/right feet. On hardware at 1.2 m/s (barefoot; averaged over four floor materials), QuietWalk reduces mean A-weighted noise level by 7.17 dB and peak noise level by 4.98 dB under a consistent recording setup. Cross-footwear experiments (barefoot, skate shoes, athletic sneakers, and high heels) across multiple surfaces further demonstrate robust adaptation to footwear-induced contact variations.

Haptic feedback has been a long-missed feature in robotic-assisted surgery, one that would allow surgeons to perceive tissue properties and apply controlled forces during delicate procedures. Although commercial robotic systems have begun to integrate haptic technologies, their high costs limit accessibility for training and research purposes. To address this gap, we extend our previously developed low-cost robotic surgery training setup, RoboScope, by incorporating a wrist-mounted force/torque (F/T) sensor for haptic feedback training. Wrist-mounted sensing avoids many challenges associated with tip-mounted sensors but introduces additional non-contact forces, such as gravity, sensor bias, installation offsets, and associated torques, which compromise measurement accuracy. In this paper, we propose a robust real-time compensation method based on recursive least squares (RLS). This method eliminates the need for dataset collection and frequent recalibration while adapting to changing operating conditions. Experimental validation demonstrates that the proposed approach achieves over 95% error reduction in non-contact force compensation and more than 91% in non-contact torque compensation, significantly outperforming existing methods. These results highlight the potential of our approach for providing reliable haptic feedback in robotic surgery training and research.

Contact-rich manipulation is central to many everyday human activities, requiring continuous adaptation to contact uncertainty and external disturbances through multi-modal perception, particularly vision and tactile feedback. While imitation learning has shown strong potential for learning complex manipulation behaviors, most existing approaches rely on action chunking, which fundamentally limits their ability to react to unforeseen observations during execution. This limitation becomes especially critical in contact-rich scenarios, where physical uncertainty and high-frequency tactile feedback demand rapid, reactive control. To address this challenge, we propose Tube Diffusion Policy (TDP), a novel reactive visual-tactile policy learning framework that bridges diffusion-based imitation learning with tube-based feedback control. By leveraging the expressive power of generative models, TDP learns an observation-conditioned feedback flow around nominal action chunks, forming an action tube that enables fast and adaptive reactions during execution. We evaluate TDP on the widely used Push-T benchmark and three additional challenging visual-tactile dexterous manipulation tasks. Across all benchmarks, TDP consistently outperforms state-of-the-art imitation learning baselines. Two real-world experiments further validate its robust reactivity under contact uncertainty and external disturbances. Moreover, the step-wise correction mechanism enabled by action tube significantly reduces the required denoising steps, making TDP well suited for real-time, high-frequency feedback control in contact-rich manipulation.

Continuous estimation of high-dimensional finger kinematics from forearm surface electromyography (EMG) could enable natural control for hand prostheses, AR/XR interfaces, and teleoperation. However, the complexity of human hand gestures and the entanglement of forearm muscles make accurate recognition intrinsically challenging. Existing approaches typically reduce task complexity by relying on classification-based machine learning, limiting the controllable degrees of freedom and compromising on natural interaction. We present an end-to-end framework for continuous EMG-to-kinematics regression using only consumer-grade hardware. The framework combines an 8-channel EMG armband, a single webcam, and an automatic synchronization procedure, enabling the collection of the EMG Finger-Kinematics dataset (EMG-FK), a 10-h dataset of synchronized EMG and 15 finger joint angles from 20 participants performing rich, unconstrained right-hand motions. We also introduce the Temporal Riemannian Regressor (TRR), a lightweight GRU-based model that uses sequences of multi-band Riemannian covariance features to decode finger motion. Across EMG-FK and the public emg2pose benchmark, TRR outperforms state-of-the-art methods in both intra- and cross-subject evaluation. On EMG-FK, it reaches an average absolute error of $9.79 °\pm 1.48$ in intra-subject and $16.71 °\pm 3.97$ in cross-subject. Finally, we demonstrate real-time deployment on a Raspberry Pi 5 and intuitive control of a robotic hand; TRR runs at nearly 10 predictions/s and is roughly an order of magnitude faster than state-of-the-art approaches. Together, these contributions lower the barrier to reproducible, real-time EMG-based decoding of high-dimensional finger motion, and pave the way toward more natural and intuitive control of embedded EMG-based systems.