Contact-Rich Manipulation

This study investigates the kinematic role of palm degrees of freedom (DoF) in enhancing thumb opposability in a five-finger robotic hand. A hand model consisting of a five DoF thumb and four fingers with three to four DoF is analyzed, where palm motion is introduced between adjacent fingers. To quantitatively evaluate thumb-finger interaction, the overlap workspace volume is defined based on voxelized fingertip reachable regions. Seven cases are considered, including configurations with increased total DoF and configurations in which the total DoF is maintained by redistributing DoF from the fingers to the palm. The results show that palm DoF significantly improves opposability, particularly for the ring and little fingers, by repositioning their base locations rather than simply extending their reachable range. However, when the total DoF is constrained, redistributing DoF to the palm leads to trade-offs between overlap workspace expansion and kinematic redundancy. These findings indicate that palm DoF and finger DoF play distinct roles in hand kinematics and should be considered jointly in design. This study provides a quantitative framework for evaluating palm-induced opposability without relying on object or contact models and offers practical design guidelines for incorporating palm motion in robotic hands.

Variable impedance model predictive control (MPC) formulations often treat joint stiffness as an instantaneous decision variable. The resulting feasible set strictly contains the physically realizable set under first-order actuator dynamics. We identify this as a formulation error rather than a modeling approximation, formalize the distinction between the parameter-based feasible set F_param and the realizable set F_real, and characterize the regime of mismatch via the dimensionless parameter α = ωsT (actuator bandwidth times task timescale). For the 1D hopping monoped, we prove that below an analytical threshold α_crit derived in closed form from task physics, no admissible stiffness command realizes the parameter-based prediction. Numerical validation in 1D shows monotonic deviation growth as α decreases, with the predicted scaling holding across ten parameter combinations (log-log R2 = 0.986). Mechanism transfer to planar spring-loaded inverted pendulum dynamics confirms center-of-mass and stance-timing deviation as the primary consequence, with regime-dependent friction effects as a tertiary observable. A second threshold α_infeas < α_crit establishes a floor below which restricting the admissible stiffness range cannot repair realizability, closing the conservative-tuning objection. Augmenting the prediction state with stiffness closes the mismatch by construction.

Sub-gram flapping-wing flying insect robots (FIRs) are challenging to model because of mechanical complexity in their wings, unsteady aerodynamic flow, and the difficulty of making precise measurements at a small scale. Coupling effects between roll and pitch torque actuation have not previously been measured because a two-axis sensor that is sensitive enough has not been realized. To address this shortcoming, we introduce a microfabricated gimbal design capable of precisely and simultaneously measuring roll and pitch torques as well as thrust. We then used it to measure the extent to which a pitch torque command affects roll torque and vice versa on a 180 mg piezo-actuated flapping-wing flying platform. Our results show a high coefficient of determination in the linear regression for both pitch (0.95) and roll (0.98) and low cross-correlation coefficients (-0.001 and -0.085, respectively) across the full range of simultaneous torque commands, indicating negligible cross-axis coupling. Similarly, thrust force deviates by a maximum of only 5.8% from the mean thrust value. These results validate the assumption that pitch and toll can be considered independently in control and will inform future models of how inputs affect the aerodynamics of resonant flapping-wing systems.

An asymmetric two-link robot supported atop a flat platform by wheels that roll and pivot freely, but do not slip laterally, will develop forward momentum if the joint between the links is actuated internally. In particular, oscillations in the joint angle will generate undulatory locomotion suggesting fishlike swimming. If two such robots surmount a common platform that's free to translate with its own inertial dynamics, then the individual robots' dynamics will be coupled so that the locomotion of either robot is affected by that of the other. We develop a mathematical model for this system and present simulations demonstrating its behavior. We then consider a single robot with an unactuated joint rolling atop a platform that moves under control, and show that actuation of the platform is sufficient to dictate the robot's behavior. In particular, with the acceleration of the platform as an input, the robot's heading can be made to track a chosen function of time. This is sufficient to guarantee that the robot can be induced to orbit a fixed point on the platform or to locomote persistently in a desired direction.

Collision avoidance for robotic manipulators requires enforcing full-body safety constraints in high-dimensional configuration spaces. Control Barrier Function (CBF) based safety filters have proven effective in enabling safe behaviors, but enforcing the high number of constraints needed for safe manipulation leads to theoretic and computational challenges. This work presents a framework for full-body collision avoidance for manipulators in dynamic environments by leveraging 3D Poisson Safety Functions (PSFs). In particular, given environmental occupancy data, we sample the manipulator surface at a prescribed resolution and shrink free space via a Pontryagin difference according to this resolution. On this buffered domain, we synthesize a globally smooth CBF by solving Poisson's equation, yielding a single safety function for the entire environment. This safety function, evaluated at each sampled point, yields task-space CBF constraints enforced by a real-time safety filter via a multi-constraint quadratic program. We prove that keeping the sample points safe in the buffered region guarantees collision avoidance for the entire continuous robot surface. The framework is validated on a 7-degree-of-freedom manipulator in dynamic environments.

Evaluating the pinch capability of a robotic hand is important for understanding its functional dexterity. However, many existing grasp evaluation methods rely on object geometry or contact force models, which limits their applicability during the early stages of robotic hand design. This study proposes a kinematic evaluation method for analyzing pinch configurations of robotic hands based on interactions between fingertip workspaces. First, the reachable workspace of each fingertip is computed from the joint configurations of the fingers. Then, feasible pinch configurations are detected by evaluating the relationships between fingertip pairs. Since the proposed method does not require information about object geometry or contact force models, the pinch capability of a robotic hand can be evaluated solely based on its kinematic structure. In addition, analyses are performed on four different kinematic structures of the hand to investigate their impact on the pinch configurations. The proposed evaluation framework can serve as a useful tool for comparing different robotic hand designs and analyzing pinch capability during the design stage.

In the design stage of robotic hands, it is not straightforward to quantitatively evaluate the effect of phalanx length ratios on dexterity without defining specific objects or manipulation tasks. Therefore, this study presents a framework for optimizing the phalanx length ratios of a five-finger robotic hand based on potential dexterity within a kinematic structure. The proposed method employs global manipulability, workspace volume, overlap workspace volume, and fingertip sensitivity as evaluation metrics, and identifies optimal design configurations using a weighted objective function under given constraints. The reachable workspace is discretized using a voxel-based representation, and joint motions are discretized at uniform intervals for evaluation. The optimization is performed over design sets for both the thumb and the other fingers, and design combinations that do not generate overlap workspace are excluded. The results show that each phalanx does not contribute equally to the overall dexterity, and the factors influencing each phalanx are identified. In addition, it is observed that the selection of weighting coefficients does not necessarily lead to the direct maximization of individual performance metrics, due to the non-uniform distribution of evaluation measures within the design space. The proposed framework provides a systematic approach to analyze the trade-offs among reachability, dexterity, and controllability, and can serve as a practical guideline for the kinematic design of multi-fingered robotic hands.

Shared Control methods often use impedance control to track target poses in a robotic manipulator. The guidance behavior of such controllers is shaped by the used stiffness gains, which can be varying over time to achieve an adaptive guiding. When multiple target poses are tracked at the same time with varying importance, the corresponding output wrenches have to be arbitrated with weightings changing over time. In this work, we study the stabilization of both variable stiffness in impedance control as well as the arbitration of different controllers through a scaled addition of their output wrenches, reformulating both into a holistic framework. We identify passivity violations in the closed loop system and provide methods to passivate the system. The resulting approach can be used to stabilize standard impedance controllers, allowing for the development of novel and flexible shared control methods. We do not constrain the design of stiffness matrices or arbitration factors; both can be matrix-valued including off-diagonal elements and change arbitrarily over time. The proposed methods are furthermore validated in simulation as well as in real robot experiments on different systems, proving their effectiveness and showcasing different behaviors which can be utilized depending on the requirements of the shared control approach.

Tactile sensors are increasingly integrated into dexterous robotic manipulators to enhance contact perception. However, learning manipulation policies that rely on tactile sensing remains challenging, primarily due to the trade-off between fidelity and computational cost of soft-body simulations. To address this, we present ETac, a tactile simulation framework that models elastomeric soft-body interactions with both high fidelity and efficiency. ETac employs a lightweight data-driven deformation propagation model to capture soft-body contact dynamics, achieving high simulation quality and boosting efficiency that enables large-scale policy training. When serving as the simulation backend, ETac produces surface deformation estimates comparable to FEM and demonstrates applicability for modeling real tactile sensors. Then, we showcase its capability in training a blind grasping policy that leverages large-area tactile feedback to manipulate diverse objects. Running on a single RTX 4090 GPU, ETac supports reinforcement learning across 4,096 parallel environments, achieving a total throughput of 869 FPS. The resulting policy reaches an average success rate of 84.45% across four object types, underscoring ETac's potential to make tactile-based skill learning both efficient and scalable.

Incremental Potential Contact (IPC) guarantees intersection-free simulation but suffers from high computational costs due to the expensive Hessian assembly and linear solves required by Newton's method. While Preconditioned Nonlinear Conjugate Gradient (PNCG) avoids Hessian assembly, it has historically struggled with poor convergence in stiff, contact-rich scenarios due to the lack of effective preconditioners; simple Jacobi preconditioners fail to capture the global coupling, while advanced hierarchy-based preconditioners like Multilevel Additive Schwarz (MAS) are computationally prohibitive to rebuild at every nonlinear iteration. We present MAS-PNCG, a method that unlocks the power of hierarchical preconditioning for nonlinear optimization. Our key technical innovation is a Sparse-Input Woodbury update algorithm that incrementally adapts the fine-level MAS components to rapidly evolving contact sets. This bypasses the need for full preconditioner rebuilds, reducing maintenance cost to near-zero while capturing the complex spectral properties of the contact system. Furthermore, we replace heuristic PNCG search directions with a Hessian-aware 2D subspace minimization that optimally combines the preconditioned gradient and previous direction. We also apply a fast per-subdomain conservative CCD method that ensures penetration-free trajectories while avoiding overly restrictive global step sizes. Experiments demonstrate that our MAS-PNCG outperforms state-of-the-art Newton-PCG solvers, GIPC and StiffGIPC, both preconditioned with MAS up to 5.66$\times$ and 2.07$\times$ respectively.

Unknown payloads can strongly affect compliant robotic manipulation, especially when the payload center of mass is not aligned with the tool center point. In this case, the payload generates an offset wrench at the robot wrist. During motion, this wrench is not only related to payload weight, but also to payload inertia. If it is not modeled, the compliant controller can interpret it as an external interaction wrench, which causes unintended compliant motion, larger tracking error, and reduced transport accuracy. This paper presents a wrench-aware admittance control framework for unknown-payload pick-and-place using a UR5e robot. The method uses force-torque measurements in two different roles. First, a three-axis translational excitation term is used to reduce payload-induced force effects during transport without making the robot excessively stiff. Second, after grasping, the controller first estimates payload mass for transport compensation and then estimates the payload CoM offset relative to the TCP using wrist force-torque measurements collected during the subsequent translational motion. This helps improve object placement and stacking behavior. Experimental results show improved transport and placement performance compared with uncorrected placement while preserving compliant motion.

Many mechanical systems exhibit changes in their kinematic topology altering the mobility. Ideal contact is the best known cause, but also stiction and controlled locking of parts of a mechanism lead to topology changes. The latter is becoming an important issue in human-machine interaction. Anticipating the dynamic behavior of variable topology mechanisms requires solving a non-smooth dynamic problem. The core challenge is a physically meaningful transition condition at the topology switching events. Such a condition is presented in this paper. Two versions are reported, one using projected motion equations in terms of redundant coordinates, and another one using the Voronets equations in terms of minimal coordinates. Their computational properties are discussed. Results are shown for joint locking of a planar 3R mechanisms and a 6DOF industrial manipulator.

Functional fitness movements are widely used in training, competition, and health-oriented exercise programs, yet consistently enforcing repetition (rep) standards remains challenging due to subjective human judgment, time constraints, and evolving rules. Existing AI-based approaches mainly rely on learned scoring or reference-based comparisons and lack explicit rule-based, limiting transparency and deterministic rep-level validation. To address these limitations, we propose KD-Judge, a novel knowledge-driven automated judging framework for functional fitness movements. It converts unstructured rulebook standards into executable, machine-readable representations using an LLM-based retrieval-augmented generation and chain-of-thought rule-structuring pipeline. The structured rules are then incorporated by a deterministic rule-based judging system with pose-guided kinematic reasoning to assess rep validity and temporal boundaries. To improve efficiency on edge devices, including a high-performance desktop and the resource-constrained Jetson AGX Xavier, we introduce a dual strategy caching mechanism that can be selectively applied to reduce redundant and unnecessary computation. Experiments demonstrate reliable rule-structuring performance and accurate rep-level assessment, with judgment evaluation conducted on the CFRep dataset, achieving faster-than-real-time execution (real-time factor (RTF) < 1). When the proposed caching strategy is enabled, the system achieves up to 3.36x and 15.91x speedups on resource-constrained edge device compared to the non-caching baseline for pre-recorded and live-streaming scenarios, respectively. These results show that KD-Judge enables transparent, efficient, and scalable rule-grounded rep-level analysis that can complement human judging in practice.

Kinematic rigs provide a structured interface for articulating 3D meshes but lack any associated pose space, i.e., an explicit representation of the plausible manifold of joint configurations for a given mesh. Without such a pose space, stochastic sampling or manual manipulation of raw rig parameters easily results in semantic and/or geometric violations, such as anatomical hyperextension and non-physical self-intersections. We propose Video-informed Pose Spaces (ViPS), a feedforward framework that discovers the latent distribution of valid articulations for auto-rigged meshes by distilling motion priors from a pretrained video diffusion model. Unlike existing methods that rely on scarce, artist-authored 4D datasets, or focus on reconstructing instances of individual motions, ViPS transfers generative video model priors into a universal distribution over the given rig parameterization. Differentiable geometric validators applied to the skinned mesh enforce shape-specific integrity without requiring manual regularizers. Our feedforward model reveals a smooth, compact, and controllable pose space. This, in turn, supports sampling for diverse shape variations, manifold projection for inverse kinematics, and temporally coherent trajectories for animation and keyframing. Further, the distilled 3D pose samples serve as semantic proxies to guide video diffusion, effectively closing the loop between generative 2D priors and structured 3D kinematic control. Our evaluations show that ViPS, trained solely using video priors, matches the performance of state-of-the-art models trained on synthetic artist-created 4D data in both plausibility and diversity. Additionally, as a universal model, ViPS exhibits robust zero-shot generalization to out-of-distribution species and unseen skeletal topologies.

Generating intelligent robot behavior in contact-rich settings is a research problem where zeroth-order methods currently prevail. Developing methods that make use of first/second order information about rigid-body dynamics in the presence of contact holds great promise in terms of increasing the solution speed and computational efficiency. The main bottleneck in this research direction is the difficulty in obtaining gradients and Hessians that are actually useful for numerical optimization, due to pathologies in all three steps of a common simulation pipeline: i) collision detection, ii) contact dynamics, iii) time integration. This abstract proposes a method that aims to address the collision detection part of the puzzle, via a novel pipeline designed from scratch with smooth (i.e. twice) differentiability and massive vectorizability on GPUs as the main priorities. This is in contrast to standard collision detection routines that are instead optimized for runtime on CPUs and minimal memory footprint, but do employ logic and control flow that hinder differentiability and vectorization. The proposed pipeline consists of the following contributions: i) highly expressive and compute efficient SDF representations, ii) differentiable broad-phase and narrow-phase routines that use these representations to generate vertex-SDF and edge-SDF contacts, iii) a differentiable routine for convex decomposition based contact blending.

This paper investigates the control problem of dual-arm unmanned aerial manipulator systems (DAUAMs). Strong coupling between the dual-arm and the multirotor platform, together with unmodeled dynamics and external disturbances, poses significant challenges to stable and accurate operation. An adaptive event-triggered control scheme with neural network-based approximation is proposed to address these issues while explicitly considering communication constraints. First, a dynamic model of the DAUAM system is derived, and a command-filter-based backstepping framework with error compensation is constructed. Then, a neural network is employed to approximate external frictions, and an event-triggered mechanism is designed to reduce the transmission frequency of control updates, thereby alleviating communication and energy burdens. Lyapunov-based analysis shows that all closed-loop signals remain bounded and that the tracking error converges to a neighborhood of the desired trajectory within a fixed time. Finally, experiments on a self-built DAUAM platform demonstrate that the proposed approach achieves accurate trajectory tracking.

Road traffic accidents are a leading cause of fatalities worldwide. In the US, human error causes 94% of crashes, resulting in excess of 7,000 pedestrian fatalities and $500 billion in costs annually. Autonomous Vehicles (AVs) with emergency collision avoidance systems that operate at the limits of vehicle dynamics at a high frequency, a dual constraint of nonlinear kinodynamic accuracy and computational efficiency, further enhance safety benefits during adverse weather and cybersecurity breaches, and to evade dangerous human driving when AVs and human drivers share roads. This paper parameterizes a Deep Reinforcement Learning (DRL) collision avoidance policy Out-Of-Distribution (OOD) utilizing race car overtaking, without explicit geometric mimicry reference trajectory guidance, in simulation, with a physics-informed, simulator exploit-aware reward to encode nonlinear vehicle kinodynamics. Two policies are evaluated, a default uni-direction and a reversed heading variant that navigates in the opposite direction to other cars, which both consistently outperform a Model Predictive Control and Artificial Potential Function (MPC-APF) baseline, with zero-shot transfer to proportionally scaled hardware, across three intersection collision scenarios, at 31x fewer Floating Point Operations (FLOPS) and 64x lower inference latency. The reversed heading policy outperforms the default racing overtaking policy in head-to-head collisions by 30% and the baseline by 50%, and matches the former in side collisions, where both DRL policies evade 10% greater than numerical optimal control.

Inverse kinematics (IK) is a core operation in animation, robotics, and biomechanics: given Cartesian constraints, recover joint rotations under a known kinematic tree. In many real-time human avatar pipelines, the available signal per frame is a sparse set of tracked 3D joint positions, whereas animation systems require joint orientations to drive skinning. Recovering full orientations from positions is underconstrained, most notably because twist about bone axes is ambiguous, and classical IK solvers typically rely on iterative optimization that can be slow and sensitive to noisy inputs. We introduce IK-GAT, a lightweight graph-attention network that reconstructs full-body joint orientations from 3D joint positions in a single forward pass. The model performs message passing over the skeletal parent-child graph to exploit kinematic structure during rotation inference. To simplify learning, IK-GAT predicts rotations in a bone-aligned world-frame representation anchored to rest-pose bone frames. This parameterization makes the twist axis explicit and is exactly invertible to standard parent-relative local rotations given the kinematic tree and rest pose. The network uses a continuous 6D rotation representation and is trained with a geodesic loss on SO(3) together with an optional forward-kinematics consistency regularizer. IK-GAT produces animation-ready local rotations that can directly drive a rigged avatar or be converted to pose parameters of SMPL-like body models for real-time and online applications. With 374K parameters and over 650 FPS on CPU, IK-GAT outperforms VPoser-based per-frame iterative optimization without warm-start at significantly lower cost, and is robust to initial pose and input noise

Series and parallel elastic actuators offer complementary but mutually exclusive advantages, yet no existing actuator enables real-time transition between these topologies during operation. This paper presents a novel actuator design called the Dual-Topology Elastic Actuator (DTEA), which enables dynamic switching between SEA and PEA topologies during operation. A proof-of-concept prototype of the DTEA is developed to demonstrate the feasibility of the topology-switching mechanism. Experiments are conducted to evaluate the robustness and timing of the switching mechanism under operational conditions. The actuator successfully performed 324 topology-switching cycles under load without damage, demonstrating the robustness of the mechanism. The measured switching time between SEA and PEA modes is under 33.33 ms. Additional experiments are conducted to characterize the static stiffness and disturbance rejection performance in both SEA and PEA modes. Static stiffness tests show that the PEA mode is 1.53x stiffer than the SEA mode, with KSEA = 5.57 +/- 0.02 Nm/rad and KPEA = 8.54 +/- 0.02 Nm/rad. Disturbance rejection experiments show that the mean peak deflection in SEA mode is 2.26x larger than in PEA mode (5.2 deg vs. 2.3 deg), while the mean settling time is 3.45x longer (1380 ms vs. 400 ms). The observed behaviors are consistent with the known characteristics of conventional SEA and PEA actuators, validating the functionality of both modes in the DTEA actuator.

Reconstructing the shape of continuum manipulators from sparse, noisy sensor data is a challenging task, owing to the infinite-dimensional nature of such systems. Existing approaches broadly trade off between parametric methods that yield compact state representations but lack probabilistic structure, and Cosserat rod inference on factor graphs, which provides principled uncertainty quantification at the cost of a state dimension that grows with the spatial discretization. This letter combines the strength of both paradigms by estimating the coefficients of a low-dimensional Geometric Variable Strain (GVS) parameterization within a factor graph framework. A novel kinematic factor, derived from the Magnus expansion of the strain field, encodes the closed-form rod geometry as a prior constraint linking the GVS strain coefficients to the backbone pose variables. The resulting formulation yields a compact state vector directly amenable to model-based control, while retaining the modularity, probabilistic treatment and computational efficiency of factor graph inference. The proposed method is evaluated in simulation on a 0.4 m long tendon-driven continuum robot under three measurement configurations, achieving mean position errors below 2 mm for all three scenarios and demonstrating a sixfold reduction in orientation error compared to a Gaussian process regression baseline when only position measurements are available.

Kalman filter-based algorithms are fundamental for mobile robots, as they provide a computationally efficient solution to the challenging problem of state estimation. However, they rely on two main assumptions that are difficult to satisfy in practice: (a) the system dynamics must be linear with Gaussian process noise, and (b) the measurement model must also be linear with Gaussian measurement noise. Previous works have extended assumption (a) to nonlinear spaces through the Invariant Extended Kalman Filter (IEKF), showing that it retains properties similar to those of the classical Kalman filter when the system dynamics are group-affine on a Lie group. More recently, the counterpart of assumption (b) for the same nonlinear setting was addressed in [1]. By means of the proposed Iterated Invariant Extended Kalman Filter (IterIEKF), the authors of that work demonstrated that the update step exhibits several compatibility properties of the classical linear Kalman filter. In this work, we introduce a novel open-source state estimation algorithm for legged robots based on the IterIEKF. The update step of the proposed filter relies solely on proprioceptive measurements, exploiting kinematic constraints on foot velocity during contact and base-frame velocity, making it inherently robust to environmental conditions. Through extensive numerical simulations and evaluation on real-world datasets, we demonstrate that the IterIEKF outperforms the vanilla IEKF, the SO(3)-based Kalman Filter, and its iterated variant in terms of both accuracy and consistency.

The performance of legged robots depends strongly on both mechanical design and control, motivating co-design approaches that jointly optimize these parameters. However, most existing co-design studies focus on link dimensions and transmission ratios while neglecting detailed actuator design, particularly motor and gearbox parameter optimization, and are largely limited to serial open-chain mechanisms. In this work, we present a co-design framework for a planar closed-chain five-bar monoped that jointly optimizes mechanical design, motor and gearbox parameters, and control parameters for dynamic jumping. The objective is to maximize jump distance while minimizing mechanical energy consumption. The framework employs a two-stage optimization approach, where actuator optimization generates a mapping from gear ratio to actuator mass, efficiency, and peak torque, which is then incorporated into CMA-ES-based co-design optimization of the robot design and control parameters. Simulation results demonstrate an improvement of approximately 30.4% in jump distance and an 11.5% reduction in mechanical energy consumption compared to a nominal design, highlighting the effectiveness of the proposed framework for high-performance and energy-efficient planar jumping.

Research on mobile manipulation systems that physically interact with humans has expanded rapidly in recent years, opening the way to tasks which could not be performed using fixed-base manipulators. Within this context, developing suitable control methodologies is essential since mobile manipulators introduce additional degrees of freedom, making the design of control approaches more challenging and more prone to performance optimization. This paper proposes a control approach for a mobile manipulator, composed of a mobile base equipped with a robotic arm mounted on the top, with the objective of minimizing the overall kinetic energy stored in the whole-body mobile manipulator in physical human-robot interaction applications. The approach is experimentally tested with reference to a peg-in-hole task, and the results demonstrate that the proposed approach reduces the overall kinetic energy stored in the whole-body robotic system and improves the system performance compared with the benchmark method.

Underground mining robots are increasingly modeled for planning, operator training, and digital-twin workflows, where reliable actuator-level kinematics is needed to reduce hazardous in situ trials. Unlike typical open-chain industrial manipulators, representative mining machines are often linear-actuator-driven closed-chain mechanisms with planar four-bar linkages, making reusable kinematic modeling and real-time FK/IK solving challenging. We present \textit{\hl{MineRobot}}, an actuator-centered framework for modeling and solving the kinematics of this representative mechanism class. MineRobot introduces the Mining Robot Description Format (MRDF), a domain-specific representation that parameterizes mining-robot kinematics with native semantics for actuators and loop closures. It then contracts planar four-bar substructures into generalized joints and extracts, for each actuator, an Independent Topologically Equivalent Path (ITEP) classified into four canonical types. Based on this decomposition, per-type solvers are composed into a sequential forward-kinematics (FK) pipeline, while inverse kinematics (IK) is formulated as a bound-constrained actuator-length optimization solved by a Gauss--Seidel-style update scheme. By converting coupled closed-chain kinematics into small topology-aware solves, MineRobot reduces robot-specific hand derivations and supports efficient repeated FK/IK computation without treating each query as a full coupled constraint-solving problem. Experiments on representative underground mining robots demonstrate real-time FK performance and robust IK convergence within the tested operating ranges, supporting the use of MineRobot as an actuator-centered kinematic layer for planning, training, and digital-twin workflows.

Skeleton-based action recognition is widely applied in sensor-based systems, including human-computer interaction and intelligent surveillance. However, typical sensors produce sparse and discrete joint coordinates, often leading to the loss of fine-grained spatiotemporal information during dynamic movements. Furthermore, predefined physical topologies restrict modeling potential long-range dependencies. To address these challenges, we propose KGS-GCN, which integrates kinematics-driven Gaussian splatting and probabilistic topology within a graph convolutional network. A Gaussian splatting module constructs anisotropic covariance matrices by extracting instantaneous joint velocity vectors, rendering sparse skeleton sequences into multi-view continuous heatmaps rich in spatiotemporal semantics. Additionally, a probabilistic topology construction strategy transcends physical connectivity limitations by utilizing the Bhattacharyya distance to quantify statistical correlations between joint Gaussian distributions, generating an adaptive prior adjacency matrix. Finally, the lightweight multi-view rendering branch and topological GCN backbone are unified through a visual context gating mechanism, enabling seamless fusion of continuous dynamic cues with structural priors while maintaining high computational efficiency, requiring only 1.4M parameters and 1.3 GFLOPs. Extensive experiments on multiple benchmark datasets demonstrate that KGS-GCN significantly enhances the modeling of complex spatiotemporal dynamics and achieves competitive performance at low computational cost, establishing an efficient paradigm for improving the perceptual robustness of low-fidelity sensor data.

We propose TacFiLM, a lightweight modality-fusion approach that integrates visual-tactile signals into vision-language-action (VLA) models. While advances in VLAs have introduced robot policies that are both generalizable and semantically grounded, these models mainly rely on vision-based perception. Vision alone, however, cannot capture the complex interaction dynamics that occur during contact-rich manipulation, including contact forces, surface friction, compliance, and shear. While recent attempts to integrate tactile signals into VLA models often increase complexity through token concatenation or large-scale pretraining, the heavy computational demands of behaviour models necessitate lightweight fusion strategies. To address these challenges, TacFiLM outlines a post-training finetuning approach that conditions intermediate visual features on pretrained tactile representations using feature-wise linear modulation (FiLM). Experimental results on insertion and drawer opening tasks demonstrate consistent improvements in success rate, direct task performance, completion time, and force stability across both in-distribution and out-of-distribution tasks. Together, these results support our method as an effective approach to integrating tactile signals into VLA models, improving contact-rich manipulation behaviours. Project page: https://charliem7.github.io/projects/TacFilm/

We introduce CRAFT hand, a tendon-driven anthropomorphic hand with hybrid hard-soft compliance for contact-rich manipulation. The design is based on a simple idea: contact is not uniform across the hand. Impacts concentrate at joints, while links carry most of the load. CRAFT places soft material at joints and keeps links rigid, and uses rollingcontact joint surfaces to keep flexion on repeatable motion paths. Fifteen motors mounted on the fingers drive the hand through tendons, keeping the form factor compact and the fingers light. In structural tests, CRAFT improves strength and endurance while maintaining comparable repeatability. In teleoperation, CRAFT improves handling of fragile and low-friction items, and the hand covers 33/33 grasps in the Feix taxonomy. The full design costs under $600 and will be released open-source with visionbased teleoperation and simulation integration. Project page: http://craft-hand.github.io/

Existing aerial-robotics benchmarks target vehicles from hundreds of grams to several kilograms and typically expose only high-level state data. They omit the actuator-level signals required to study nano-scale quadrotors, where low-Reynoldsnumber aerodynamics, coreless DC motor nonlinearities, and severe computational constraints invalidate models and controllers developed for larger vehicles. We introduce NanoBench, an open-source multi-task benchmark collected on the commercially available Crazyflie 2.1 nano-quadrotor (takeoff weight 27 g) in a Vicon motion capture arena. The dataset comprises 172 flight recordings spanning multi-frequency excitation, geometric trajectory tracking at three speed regimes, and long-duration battery-drain hover. Each recording provides synchronized Vicon ground truth, raw IMU data, onboard extended Kalman filter (EKF) estimates, PID controller internals, and motor PWM commands at 100 Hz, alongside battery telemetry at 10 Hz, crossaligned by gyroscope-based correlation on a 1 ms search grid. NanoBench defines standardized evaluation protocols, train/test splits, and open-source baselines for three tasks: nonlinear system identification, closed-loop controller benchmarking, and onboard state estimation assessment. To our knowledge, it is the first public dataset to jointly provide actuator commands, controller internals, and estimator outputs with millimeter-accurate ground truth on a commercially available nano-scale aerial platform.

Aerodynamic promptness quantifies how rotor-speed variations generate multirotor wrench variations, but its Euclidean formulation assigns the same local cost to a given rotor acceleration at every operating speed. This work develops a capacity-aware extension for redundant multirotors with arbitrary numbers of heterogeneous rotors and wrench components. Under bounded motor torque and aerodynamic drag, each generally asymmetric instantaneous rotor-acceleration interval contains a largest zero-centered subset whose radius defines the symmetric acceleration capacity (SAC). The SAC induces a Riemannian metric on the positive-capacity rotor-speed region. Propagating its co-metric through the nonlinear rotor-speed-to-wrench differential yields a state-attached task-rate capability matrix and ellipsoid. The corresponding inverse quadratic form equals the minimum normalized rotor-acceleration effort required to realize a prescribed wrench rate, while the ellipsoid volume defines the drag-aware aerodynamic manipulability (DAAM) index. Fiberwise DAAM maximization provides a task-coordinate-invariant criterion for selecting task-equivalent actuator states; its maximizing set exists on compact regular domains and can be nonconvex and set valued. Low-dimensional two- and three-rotor studies make the resulting fiberwise geometry and parameter dependence directly visible. A complementary two-rotor use case shows how DAAM can inform a continuous allocation section subject to directional motor-torque feasibility. For two heterogeneous propulsion systems, the resulting sections reduce saturation-induced force-tracking degradation relative to the pseudoinverse in the faster command bands

Autonomous driving in off-road environments presents significant challenges due to the dynamic and unpredictable nature of unstructured terrain. Traditional kinodynamic models often struggle to generalize across diverse geometric and semantic terrain types, underscoring the need for real-time adaptation to ensure safe and reliable navigation. We propose VertiAdaptor (VA), a novel online adaptation framework that efficiently integrates elevation with semantic embeddings to enable terrain-aware kinodynamic modeling and planning via function encoders. VA learns a kinodynamic space spanned by a set of neural ordinary differential equation basis functions, capturing complex vehicle-terrain interactions across varied environments. After offline training, the proposed approach can rapidly adapt to new, unseen environments by identifying kinodynamics in the learned space through a computationally efficient least-squares calculation. We evaluate VA within the Verti-Bench simulator, built on the Chrono multi-physics engine, and validate its performance both in simulation and on a physical Verti-4-Wheeler platform. Our results demonstrate that VA improves prediction accuracy by up to 23.9% and achieves a 5X faster adaptation time, advancing the robustness and reliability of autonomous robots in complex and evolving off-road environments.

Cooperative transport and manipulation of heavy or bulky payloads by multiple manipulators requires coordinated formation tracking, while simultaneously enforcing strict safety constraints in varying environments with limited communication and real-time computation budgets. This paper presents a distributed control framework that achieves consensus coordination with safety guarantees via hierarchical event-triggered control barrier functions (CBFs). We first develop a consensus-based protocol that relies solely on local neighbor information to enforce both translational and rotational consistency in task space. Building on this coordination layer, we propose a three-level hierarchical event-triggered safety architecture with CBFs, which is integrated with a risk-aware leader selection and smooth switching strategy to reduce online computation. The proposed approach is validated through real-world hardware experiments using two Franka manipulators operating with static obstacles, as well as comprehensive simulations demonstrating scalable multi-arm cooperation with dynamic obstacles. Results demonstrate higher precision cooperation under strict safety constraints, achieving substantially reduced computational cost and communication frequency compared to baseline methods.

Accurate relative localization is critical for multi-robot cooperation. In robot groups, measurements from different robots arrive asynchronously and with clock time-offsets. Although Continuous-Time (CT) formulations have proved effective for handling asynchronous measurements in single-robot SLAM and calibration, extending CT methods to multi-robot settings faces great challenges in achieving high-accuracy, low-latency, and high-frequency performance. In particular, existing CT methods suffer from the inherent query-time delay of unclamped B-splines and high optimization latency. This paper proposes CT-RIO, a novel Continuous-Time Relative-Inertial Odometry framework. We adopt Clamped Non-Uniform B-splines (C-NUBS) to represent states, eliminating the query-time delay. We further augment C-NUBS with closed-form extension and shrinkage operations that preserve the spline shape, making it suitable for online estimation and enabling flexible knot management. This flexibility leads to the concept of a knot-keyknot strategy, which supports spline extension at high frequency while retaining sparse keyknots for adaptive relative motion modeling. We then formulate a reference-centric sliding-window relative localization problem that operates purely on relative kinematics and inter-robot constraints. To enable low-latency and high-frequency estimation, we decompose the tightly coupled optimization into robot-wise subproblems and solve them in parallel using asynchronous block coordinate descent. Extensive experiments show that CT-RIO converges from time-offsets as large as 264 ms to sub-millisecond within 3 s, and achieves RMSEs of 0.046 m and 1.8 degree. It consistently outperforms evaluated published methods, with improvements of up to 60% under high-speed motion.

Flexible endoscopic continuum manipulators offer high dexterity and access to complex anatomy, but nonlinear hysteresis limits feedforward control accuracy. Closed-loop control can compensate for these errors but requires accurate six-degree-of-freedom (6D) end-effector pose feedback. We present MarUco, a markerless 6D pose estimation framework for closed-loop control using only stereo vision during operation. A photorealistic pseudo-rigid-body simulation pipeline generates large-scale annotated training data without manual labeling. A multifeature fusion network integrates masks, keypoints, heatmaps, and bounding boxes from both stereo views to estimate an initial pose, followed by a learned single-pass render-and-compare module that refines the pose without iterative optimization. Kinematics-free hand-eye calibration estimates camera-to-robot-base extrinsics, and self-supervised adaptation uses unlabeled real stereo pairs to mitigate sim-to-real pose error. Across 1,000 real samples, MarUco achieves translation and rotation errors of 0.78 $\pm$ 0.50 mm and 3.07 $\pm$ 1.25°, respectively, with a total processing time of 52.4 ms per stereo pair. In closed-loop experiments over eight reference paths, MarUco achieves a mean terminal translation error of 1.8 mm, an 88% reduction relative to uncompensated open-loop control. To the best of our knowledge, this is the first markerless position-based visual servoing framework for continuum manipulators.

Contact-rich teleoperation logs expose a policy I/O design choice: demonstrations may contain the robot execution (E), leader command (C), or both. These signals are not interchangeable: E2E may discard contact-generating command offsets, whereas E2C preserves these offsets but omits the robot's execution response. We propose Dual-State Conditioning (EC2C), which conditions on both E and C while predicting future C, exposing command-execution mismatch as a cue for contact, latency, payload, and operator compensation; in quasi-static contact, this cue is often force-correlated. On a low-cost setup without force, tactile, or motor-current policy input, EC2C outperforms E2E and a strong E2C baseline across several real-world contact-rich, force-sensitive, and dynamic tasks. These results support EC2C as a practical default I/O setting for contact-rich imitation learning. We further formulate latency-adaptive inpainting as a temporal extension of this I/O choice for action-chunking policies, and discuss when long histories help dynamic inference or introduce causal confounding.

Continuum soft robots are inherently underactuated and subject to intrinsic input constraints, making dynamic control particularly challenging, especially in hybrid rigid-soft robots. While most existing methods focus on quasi-static behaviors, dynamic tasks such as swing-up require accurate exploitation of continuum dynamics. This has led to studies on simple low-order template systems that often fail to capture the complexity of real continuum deformations. Model-based optimal control offers a systematic solution; however, its application to rigid-soft robots is often limited by the computational cost and inaccuracy of numerical differentiation for high-dimensional models. Building on recent advances in the Geometric Variable Strain model that enable analytical derivatives, this work investigates three optimal control strategies for underactuated soft systems -- Direct Collocation, Differential Dynamic Programming, and Nonlinear Model Predictive Control -- to perform dynamic swing-up tasks. To address stiff continuum dynamics and constrained actuation, implicit integration schemes and warm-start strategies are employed to improve numerical robustness and computational efficiency. The methods are evaluated in simulation on three Rigid-Soft and high-order soft benchmark systems -- the Soft Cart-Pole, the Soft Pendubot, and the Soft Furuta Pendulum -- highlighting their performance and computational trade-offs.

Articulation modeling enables robots to learn joint parameters of articulated objects for effective manipulation which can then be used downstream for skill learning or planning. Existing approaches often rely on prior knowledge about the objects, such as the number or type of joints. Some of these approaches also fail to recover occluded joints that are only revealed during interaction. Others require large numbers of multi-view images for every object, which is impractical in real-world settings. Furthermore, prior works neglect the order of manipulations, which is essential for many multi-DoF objects where one joint must be operated before another, such as a dishwasher. We introduce PokeNet, an end-to-end framework that estimates articulation models from a single human demonstration without prior object knowledge. Given a sequence of point cloud observations of a human manipulating an unknown object, PokeNet predicts joint parameters, infers manipulation order, and tracks joint states over time. PokeNet outperforms existing state-of-the-art methods, improving joint axis and state estimation accuracy by an average of over 27% across diverse objects, including novel and unseen categories. We demonstrate these gains in both simulation and real-world environments.

In this work, we present Tilt-Ropter, a fully actuated hybrid aerial-terrestrial vehicle (HATV) that integrates tilt rotors with passive wheels to enable efficient multi-modal locomotion. Unlike conventional underactuated HATVs, the fully actuated design of Tilt-Ropter allows decoupled force and torque control, improving maneuverability and ground locomotion efficiency. A unified nonlinear model predictive controller (NMPC) is developed to track reference trajectories, enforce non-holonomic constraints, and accommodate contact effects across locomotion modes, while ensuring actuator feasibility through dedicated control allocation. To address complex wheel-ground dynamics, an external wrench estimator is incorporated to provide real-time interaction wrench estimates. The system is validated through simulation and real-world experiments, including seamless air-ground transitions and trajectory tracking tasks. Experimental results demonstrate low tracking errors in both modes and reveal a 92.8% reduction in power consumption during ground locomotion compared with flight, highlighting the platform's potential for long-duration missions where energy efficiency is critical.

Tactile feedback is important for contact-rich robotic manipulation, yet effective use of tactile observations remains challenging when tactile signals are image-like, hardware-dependent, and only weakly aligned with external visual observations. This study addresses this representation-learning problem by proposing a visuo-tactile contrastive learning framework for imitation-based manipulation. The method aligns external RGB observations and calibrated tactile images in a shared embedding space using a CLIP-style objective, and integrates the resulting representation into an Action Chunking Transformer (ACT) policy. A low-cost visuo-tactile gripper (LVTG) is proposed to provide a modular and durable sensing platform for reproducible data collection, supplying tactile observations that can be used by downstream manipulation algorithms. Experiments on contact-rich manipulation tasks show that tactile feedback improves the average task completion rate from 30% for a vision-only ACT baseline to 42%, and that the proposed contrastive pretraining further increases the completion rate to 54%. These results indicate that explicitly aligning visual and tactile observations provides more useful contact-aware features for downstream policy learning than directly adding tactile images without pretraining.

A key challenge in contact-rich dexterous manipulation is the need to jointly reason over global geometry and nonsmooth contact dynamics. End-to-end policies bypass this complexity, but often require large amounts of data and transfer poorly from simulation to reality. We address the limitations with a simple insight: dexterous manipulation is inherently hierarchical--at a high level, a robot decides where to touch (geometry); at a low level it determines how to move the object through contact dynamics. Building on this insight, we propose a hierarchical RL--MPC framework in which a high-level reinforcement learning (RL) policy predicts a contact intention, a novel object-centric interface that specifies (i) an object-surface contact location and (ii) a post-contact object subgoal pose. Conditioned on the contact intention, a low-level contact-implicit model predictive control (MPC) optimizes local contact modes and real-time (re)plans through contact dynamics to generate robot actions that robustly move the object toward each subgoal. We evaluate the framework on non-prehensile tasks, including geometry-generalized pushing across diverse object shapes, pivoting/flipping-based object reorientation, and environment-assisted object repositioning. It achieves high success rate with substantially reduced data (10 times less than end-to-end baselines), highly robust performance, and zero-shot sim-to-real transfer.

Reconstructing biomechanically realistic 3D human motion - recovering both kinematics (motion) and kinetics (forces) - is a critical challenge. While marker-based systems are lab-bound and slow, popular monocular methods use oversimplified, anatomically inaccurate models (e.g., SMPL) and ignore physics, fundamentally limiting their biomechanical fidelity. In this work, we introduce MonoMSK, a hybrid framework that bridges data-driven learning and physics-based simulation for biomechanically realistic 3D human motion estimation from monocular video. MonoMSK jointly recovers both kinematics (motions) and kinetics (forces and torques) through an anatomically accurate musculoskeletal model. By integrating transformer-based inverse dynamics with differentiable forward kinematics and dynamics layers governed by ODE-based simulation, MonoMSK establishes a physics-regulated inverse-forward loop that enforces biomechanical causality and physical plausibility. A novel forward-inverse consistency loss further aligns motion reconstruction with the underlying kinetic reasoning. Experiments on BML-MoVi, BEDLAM, and OpenCap show that MonoMSK significantly outperforms state-of-the-art methods in kinematic accuracy, while for the first time enabling precise monocular kinetics estimation.

With the explosive growth of rigid-body simulators, policy learning in simulation has become the de facto standard for most rigid morphologies. In contrast, soft robotic simulation frameworks remain scarce and are seldom adopted by the soft robotics community. This gap stems partly from the lack of easy-to-use, general-purpose frameworks and partly from the high computational cost of accurately simulating continuum mechanics, which often renders policy learning infeasible. In this work, we demonstrate that rapid soft robot policy learning is indeed achievable via implicit time-stepping. Our simulator of choice, DisMech, is a general-purpose, fully implicit soft-body simulator capable of handling both soft dynamics and frictional contact. We further introduce delta natural curvature control, a method analogous to delta joint position control in rigid manipulators, providing an intuitive and effective means of enacting control for soft robot learning. To highlight the benefits of implicit time-stepping and delta curvature control, we conduct extensive comparisons across four diverse soft manipulator tasks against one of the most widely used soft-body frameworks, Elastica. With implicit time-stepping, parallel stepping of 500 environments achieves up to 6x faster speeds for non-contact cases and up to 40x faster for contact-rich scenarios. Finally, a comprehensive sim-to-sim gap evaluation--training policies in one simulator and evaluating them in another--demonstrates that implicit time-stepping provides a rare free lunch: dramatic speedups achieved without sacrificing accuracy.

Maintaining whole-body stability and motion tracking under large interaction forces remains challenging for humanoids. We present Thor, a reinforcement learning framework for forceful humanoid loco-manipulation. Thor jointly trains lower-body, waist, and upper-body policies with shared whole-body observations and body-specific rewards to coordinate locomotion and force adaptation, waist posture regulation, and upper-body motion tracking. We further introduce a force-adaptive torso-tilt (FAT2) objective that derives a load-dependent horizontal center-of-mass offset reference from quasi-static moment balance. Capacity-matched simulation blations show that the three-policy architecture improves tracking under large external force disturbances, while real-world ablations demonstrate that FAT2 increases peak pulling capability. On the Unitree G1, Thor achieves mean peak dual-hand pulling forces of 167.7 N and 145.5 N during backward and forward locomotion, exceeding the best-performing baseline by 68.9% and 74.7%, respectively. Real-world demonstrations include opening a fire door with one hand using approximately 60 N of pulling force and towing a 1.7-ton passenger car.

Inverse Kinematics (IK) is a core problem in robotics, in which joint configurations are found to achieve a (collision-free) desired end-effector pose. Modern IK solvers face a fundamental trade-off: analytical methods are fast but lack generality, while numerical optimization-based methods are broadly applicable but prone to local minima and high computational costs. To overcome this challenge, we introduce HJCD-IK, a GPU-accelerated, sampling-based hybrid solver. By pairing a novel orientation-aware greedy coordinate descent initialization with Jacobian-based polishing and a parallel collision filter, our method achieves up to order-of-magnitude gains in speed and accuracy over state-of-the-art solvers, consistently finding collision-free solutions on the accuracy-latency Pareto frontier, while producing a diverse distribution of high-quality samples. We validate our solver on a physical Franka manipulator and release our code open-source.

Robotic fabric manipulation remains challenging due to fabric deformability and occlusions from wrinkles and the manipulator. This paper defines Random-to-Target Fabric Flattening (RTFF) as the task of bringing a randomly wrinkled fabric to an arbitrary user-specified wrinkle-free target pose. RTFF requires simultaneous flattening and pose alignment, where the two objectives are inherently coupled since flattening the fabric displaces its pose, while realigning it tends to introduce wrinkles. To solve this task, this paper anchors both the current and target fabric states to the same template mesh, enabling direct vertex-level wrinkle and pose assessment without registration. Building on this representation, a hybrid Imitation Learning--Visual Servoing (IL--VS) RTFF policy is proposed. A novel Mesh Action Chunking Transformer (MACT) leverages structured mesh observations to achieve goal-conditioned coarse alignment from a compact demonstration set, after which VS ensures precise convergence to the target. The policy is validated on a real dual-arm teleoperation system, demonstrating precise alignment to unseen target poses, fabric types, and scales. Code and videos: https://kaitang98.github.io/RTFF_Policy/

We present a learnable physics-based model that predicts motion of the robot end effector and reaction force-torque in contact-rich manipulation. The model represents the end effector and the environment as interacting meshes in a graph structure, and conditions its prediction explicitly on the applied control input. It predicts object-level pose update directly, while the reaction torque emerges from a per-vertex force field. Training is self-supervised using only joint encoder and force-torque data while the robot is randomly touching the environment without task context. In simulation, our model transfers to peg insertion with unseen concave geometry, where an MPC agent using it reaches up to 98% success rate, and after fine-tuning on self-collected data matches an agent planning with the ground truth dynamics at the tightest 1 mm clearance. In the real world, it outperforms the system-identified MuJoCo model by 45% in position and by 74% and 63% in force and torque error.

In physical human-robot collaboration (pHRC) settings, humans and robots collaborate directly in shared environments. Robots must analyze interactions with objects to ensure safety and facilitate meaningful workflows. One critical aspect is human/object detection, where the contacted object is identified. Past research introduced binary machine learning classifiers to distinguish between soft and hard objects. This study improves upon those results by evaluating three-class human/object detection models, offering more detailed contact analysis. A dataset was collected using the Franka Emika Panda robot manipulator, exploring preprocessing strategies for time-series analysis. Models including LSTM, GRU, and Transformers were trained on these datasets. The best-performing model achieved 91.11% accuracy during real-time testing, demonstrating the feasibility of multi-class detection models. Additionally, a comparison of preprocessing strategies suggests a sliding window approach is optimal for this task.

This paper presents an immersive bilateral teleoperation framework for beyond-human-scale manipulators, combining motion/force transparency with enhanced operator embodiment through virtual reality (VR) and distributed haptic feedback. The platform integrates a full-scale industrial hydraulic manipulator, a 7-DoF haptic exoskeleton, and head-tracked visual feedback to reinforce operator agency and self-location. A force-sensorless adaptive controller incorporates an augmented human-robot dynamic model to address master-surrogate asymmetries, input nonlinearities, model uncertainties, and communication delays. Rigorous analysis establishes semi-global uniform ultimate boundedness of the closed-loop system. Extensive full-scale experiments demonstrate precise motion and force tracking with scaling up to 1:13 and 1:1000, respectively, and fixed or time-varying delays up to 150 ms. Coordinated 6-DoF pick-and-place and multi-axis contact tasks further validate system performance. A ten-participant user study supports system usability and indicates approximately 50% higher normalized embodiment scores with VR than with monitor-based feedback. These results advance intuitive, force-reflected remote manipulation at industrial scale.

This paper investigates whether sequential context improves goal-conditioned Reinforcement Learning in sparse-reward manipulation tasks. While Hindsight Experience Replay (HER) addresses reward sparsity through goal relabeling, its operation on isolated transitions limits its ability to capture temporal dependencies inherent in joint-space control. We hypothesize that incorporating motion history can enhance policy learning and introduce CONTHER, which integrates a Transformer-based architecture with a modified HER replay buffer. The Transformer encodes sequences of prior states and goals to provide temporal awareness, while the buffer populates experience with artificially successful trajectories. Two architectural variants are analyzed to examine how contextual information should be integrated. In simulated point-reaching tasks with a UR3 manipulator, CONTHER achieves a 38.46% higher average success rate compared to baselines and outperforms the strongest baseline by 28.21%, with faster convergence and more stable learning. The framework is further evaluated on three dynamic tasks requiring complex trajectory following and obstacle avoidance, where temporal context is critical. By operating directly on joint velocities, the approach provides a foundation for transfer to physical systems. The primary contribution is a systematic investigation into fusing sequential context with goal relabeling, offering insights into how temporal awareness benefits policy learning.

This paper presents a novel approach to real-time safety monitoring in human-robot collaborative manufacturing environments through a wrist-mounted Inertial Measurement Unit (IMU) system integrated with a Predictive Safety Model (PSM). The proposed system extends previous PSM implementations through the adaptation of a spring-damper-mass model specifically optimized for wrist motions, employing probabilistic safety assessment through impedance-based computations. We analyze our proposed impedance-based safety approach with frequency domain methods, establishing quantitative safety thresholds through comprehensive comparative analysis. Experimental validation across three manufacturing tasks - tool manipulation, visual inspection, and pick-and-place operations. Results show robust performance across diverse manufacturing scenarios while maintaining computational efficiency through optimized parameter selection. This work establishes a foundation for future developments in adaptive risk assessment in real-time for human-robot collaborative manufacturing environments.

Loss of hand function due to conditions like stroke or multiple sclerosis significantly impacts daily activities. Robotic rehabilitation provides tools to restore hand function, while novel methods based on surface electromyography (sEMG) enable the adaptation of the device's force output according to the user's condition, thereby improving rehabilitation outcomes. This study aims to achieve accurate force estimations during medium wrap grasps using a single sEMG sensor pair, thereby addressing the challenge of escalating sensor requirements for precise predictions. We conducted sEMG measurements on 13 subjects at two forearm positions, validating results with a hand dynamometer. We established flexible signal-processing steps, yielding high peak cross-correlations between the processed sEMG signal (representing meaningful muscle activity) and grip force. Influential parameters were subsequently identified through sensitivity analysis. Leveraging a novel data-driven Koopman operator theory-based approach and problem-specific data lifting techniques, we devised a methodology for the estimation and short-term prediction of grip force from processed sEMG signals. A weighted mean absolute percentage error (wMAPE) of approx. 5.5% was achieved for the estimated grip force, whereas predictions with a 0.5-second prediction horizon resulted in a wMAPE of approx. 17.9%. The methodology proved robust regarding precise electrode positioning, as the effect of sensing position on error metrics was non-significant. The algorithm executes exceptionally fast, processing, estimating, and predicting a 0.5-second sEMG signal batch in just approx. 30 ms, facilitating real-time implementation.

The motions of mechanisms can be described in terms of screw coordinates by means of an exponential mapping. The product of exponentials (POE) describes the configuration of a chain of bodies connected by lower pair joints. The kinematics is thus given in terms of joint screws. The POE serves to express loop constraints for mechanisms as well as the forward kinematics of serial manipulators. Besides the compact formulations, the POE gives rise to purely algebraic relations for derivatives wrt. joint variables. It is known that the partial derivatives of the instantaneous joint screws (columns of the geometric Jacobian) are determined by Lie brackets the joint screws. Lesser-known is that derivative of arbitrary order can be compactly expressed by Lie brackets. This has significance for higher-order forward/inverse kinematics and dynamics of robots and multibody systems. Various relations were reported but are scattered in the literature and insufficiently recognized. This paper aims to provide a comprehensive overview of the relevant relations. Its original contributions are closed form and recursive relations for higher-order derivatives and Taylor expansions of various kinematic relations. Their application to kinematic control and dynamics of robotic manipulators and multibody systems is discussed.

Precision reducers couple contact geometry, bearing support, structural deformation, and loading history. This paper presents a dynamic toolkit connecting distributed local contacts to the complete mechanical reaction path. Work-conjugate maps transfer displacement, reaction, and tangent contributions between contacts and rigid or reduced coordinates, with explicit allocation of contact and body elasticity. An implicit generalized-alpha solution distinguishes trial evaluations from accepted history. Contact records then support performance protocols and configured geometric or constitutive feedback. The numerical studies focus on mechanical coupling and pressure recovery. An idealized annular housing retains physical interfaces while its structural coordinates are reduced. Two reductions with similar static errors have cross-port response errors of 24.975 and 0.312 percent over the same frequency band relative to a common parent model. In a shared-pin example, a 20 micrometer radial displacement of one wheel changes the load on a second, fixed wheel by approximately 75 N. Removing cross-station compliance removes this incremental transfer on the tested sleeve-seating branch. A double-wheel cycloidal assembly relates torsional branch response to aggregate contact-load variation and normalized pressure fields. The pressure maxima remain sensitive to resolution despite small discrete force residuals. Further formulations specify how motion and contact records support precision, vibration, heat, wear, and durability models with their required inputs. The framework separates model representation and numerical resolution while retaining common definitions of motion, force, and observation.

The COVID19 pandemic had enormous economic and societal consequences. Contact tracing is an effective way to reduce infection rates by detecting potential virus carriers early. However, this was not generally adopted in the recent pandemic, and privacy concerns are cited as the most important reason. We substantially improve the privacy guarantees of the current state of the art in decentralized contact tracing. Whereas previous work was based on statistical inference only, we augment the inference with a learned neural network and ensure that this neural augmentation satisfies differential privacy. In a simulator for COVID19, even at epsilon=1 per message, this can significantly improve the detection of potentially infected individuals and, as a result of targeted testing, reduce infection rates. This work marks an important first step in integrating deep learning into contact tracing while maintaining essential privacy guarantees.

This paper outlines the specifications and design approach used to construct a full body imaging scanner capable of capturing skin lesions at a dermatoscopic level using cameras mounted on the end-effectors of four UR10 manipulators. The system possesses a view-planning algorithm capable of appropriately selecting the best camera position to acquire images of moles, a high-level controller to allow the manipulators to work simultaneously and a collision-detector that halts the manipulators when they make contact with an object or a person. We evaluate the system through real-patient full-body scans, comparing acquired images against contact dermoscopy and an existing total-body photography system (Vectra) across clinically relevant lesion features, and quantify true optical resolving power using a USAF 1951 resolution target, yielding a smallest resolvable feature size of 22.1 microns for our scanner compared to 8.8 microns for contact dermoscopy. Results show the scanner consistently outperforms Vectra across most clinically relevant features and achieves comparable performance to contact dermoscopy for the majority of features assessed. By acquiring dermatoscopic-quality images automatically and without contact, and without requiring a separate manual dermoscopic examination, the scanner closes part of the gap between total-body photography and handheld dermoscopy, suggesting potential for future integration into screening workflows.

The pandemic in 2020 and 2021 had enormous economic and societal consequences, and studies show that contact tracing algorithms can be key in the early containment of the virus. While large strides have been made towards more effective contact tracing algorithms, we argue that privacy concerns currently hold deployment back. The essence of a contact tracing algorithm constitutes the communication of a risk score. Yet, it is precisely the communication and release of this score to a user that an adversary can leverage to gauge the private health status of an individual. We pinpoint a realistic attack scenario and propose a contact tracing algorithm with differential privacy guarantees against this attack. The algorithm is tested on the two most widely used agent-based COVID19 simulators and demonstrates superior performance in a wide range of settings. Especially for realistic test scenarios and while releasing each risk score with epsilon=1 differential privacy, we achieve a two to ten-fold reduction in the infection rate of the virus. To the best of our knowledge, this presents the first contact tracing algorithm with differential privacy guarantees when revealing risk scores for COVID19.

How to endow aerial robots with the ability to operate in close proximity remains an open problem. The core challenges lie in the propulsion system's dual-task requirement: generating manipulation forces while simultaneously counteracting gravity. These competing demands create dynamic coupling effects during physical interactions. Furthermore, rotor-induced airflow disturbances critically undermine operational reliability. Although fully-actuated unmanned aerial vehicles (UAVs) alleviate dynamic coupling effects via six-degree-of-freedom (6-DoF) force-torque decoupling, existing implementations fail to address the aerodynamic interference between drones and environments. They also suffer from oversized designs, which compromise maneuverability and limit their applications in various operational scenarios. To address these limitations, we present FLOAT Drone (FuLly-actuated cOaxial Aerial roboT), a novel fully-actuated UAV featuring two key structural innovations. By integrating control surfaces into fully-actuated systems for the first time, we significantly suppress lateral airflow disturbances during operations. Furthermore, a coaxial dual-rotor configuration enables a compact size while maintaining high hovering efficiency. Through dynamic modeling, we have developed hierarchical position and attitude controllers that support both fully-actuated and underactuated modes. Experimental validation through comprehensive real-world experiments confirms the system's functional capabilities in close-proximity operations.

Text-driven motion editing and intra-structural retargeting, where skeletons share topology but may differ in bone lengths and rest pose, are traditionally handled by fragmented pipelines with incompatible inputs and representations: editing relies on specialized generative steering, while retargeting is deferred to geometric post-processing. We present a unified conditional-flow framework that casts generation, semantic editing, and intra-structural retargeting as condition-modulated transport within one text- and skeleton-conditioned rectified-flow model. Under this formulation, editing changes the semantic condition while preserving skeletal structure, whereas retargeting changes the skeletal condition while preserving motion semantics. This makes FlowEdit-style transport a unified inference rule for motion manipulation rather than a task-specific editor. To instantiate this for articulated 3D motion, we develop a text- and skeleton-conditioned rectified-flow transformer. The model uses per-joint tokenization and explicit joint self-attention to capture spatial kinematic dependencies. We further inject text conditions at both joint and frame levels, while residual multi-condition classifier-free guidance balances text adherence and skeletal conformity. Experiments on SnapMoGen and a multi-character Mixamo subset show that one trained model supports text-to-motion generation, zero-shot editing, and zero-shot intra-structural retargeting without task-specific fine-tuning. This unified framework replaces separate pipelines with a single conditional motion transport model while keeping the same-topology retargeting scope explicit.

Accurate tactile forecasts need not improve force-constrained control. We study a 652,157-parameter action-conditioned visuotactile world model with matched behavior cloning, policy learning in imagination, independent reactive implicit Q-learning, and model-assisted force feedback. A fixed protocol executes 34 policies on 120 fresh MuJoCo environments spanning geometry and physical-parameter shifts, plus 324 independently replayed action branches on 12 additional ID environments. Visuotactile dynamics reduce force action-effect MAE from 0.413 N for persistence to 0.338 N. Model-assisted feedback raises ID force-budgeted success from 73.3% to 93.3%, with paired difference +20.0 [+6.7,+33.4] percentage points (95% CI), with the difference occurring during scripted lowering. Its pooled difference is +3.9 [-4.5,+11.7] points. Imagined RL achieves 11.9% pooled joint success versus 25.0% for reactive IQL. An empirical tactile-residual stress test adds 330 executions. The evidence concerns rigid-box lifting after a common approach, without physical-robot transfer or a closed-loop safety guarantee.